• 동력기계공학회지
• /
• 제16권4호
• /
• pp.44-50
• /
• 2012

The present numerical study was performed to determine how the two perforated baffles( Inclined angle=$5^{\circ}$; perforation diameter=2cm) placed at a rectangular duct affect heat transfer and associated friction factors. The parametric effects of perforated baffles(3, 6 and 12 holes) and flow Reynolds number ranging from 28,900 to 61,000 on the heated target surface are explored. As for the investigation of heat transfer behaviours on the local Nusselt number with two baffles placed at $x/D_h=0.8$ and $x/D_h=0.8$ of the edge baffles, it is evident that the average Nusselt number increases with increasing number of holes, but the friction factor decreases with an increase in the hole number placed at baffles. The numerical results by commercial code CFX 10.0 are confirmed with the experimental data.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.849-861
• /
• 1997

In this study, the effect of hole geometry of the cooling system on the flow and temperature field was numerically calculated. The finite volume method was employed to discretize the governing equation based on the non-orthogonal coordinate with non-staggered variable arrangement. The standard k-.epsilon. turbulence model was used and also the predicted results were compared with the experimental data to validate numerical modeling. The predicted results showed good agreement in all cases. To analyze the effect of the discharge coefficient for slots of different length to width, the inlet chamfering and radiusing holes were considered. The discharge coefficient was increased with increment of the chamfering ratio, radiusing ratio and slot length to width and also the effect of radiusing showed better result than chamfering in all cases. In order to analyze the difference between the predicted results with plenum region and without plenum region, the velocity profiles of jet exit region for a various flow conditions were calculated. The normal velocity components of jet exit showed big difference for the low slot length to width and high blowing rate cases. To analyze the flow phenomena injected from a row of inclined holes in a real turbine blade, three dimensional flow and temperature distribution of the region including plenum, hole and cross stream with flow conditions were numerically calculated. The results have shown three-dimensional flow characteristics, such as the development of counter rotating vortices, jetting effect and low momentum region within the hole in addition to counter rotating vortex structure in the cross stream.

• 설비공학논문집
• /
• 제19권11호
• /
• pp.751-760
• /
• 2007

Baffles enhance heat transfer by disturbing boundary layer and bulk flow, creating impingement, and increasing heat transfer surface area. This study was performed to determine how the two inclined baffles (${\alpha}=5^{\circ}$ perforated models) placed at a rectangular channel affect heat transfer and associated friction characteristics. The parametric effects of perforated baffles (3, 6 and 12 holes) and flow Reynolds number ranging from 28,900 to 61,800 on the heated target surface are explored. Comparisons of the experimental data with the numerical results by commercial code CFX 10.0 are presented. As for the investigation of heat transfer behaviors on local Nusselt number with two baffles placed at $x/D_h=0.8$ and $x/D_h=8.0$ of the edge of baffles, it is evident that the inclined perforated baffles augment overall heat transfer significantly by both jet impingement and boundary layer separation. There exists an optimum perforation density to maximize heat transfer coefficients; i.e., the average Nusselt number increases with increasing number of holes, but the friction factor decreases with an increase in the hole number placed at baffles.

• 한국유체기계학회 논문집
• /
• 제11권6호
• /
• pp.31-37
• /
• 2008

Film cooling effectiveness on the convergent or divergent channel was measured by pressure sensitive paint technique. The channel convergent or divergent angle was changed from $-5^{\circ}$ to $10^{\circ}$ and the tested blowing ratios were 0.5, 1 and 2. Results showed that the film cooling effectiveness on the convergent channel was not much affected by the convergent angle. With divergent film cooled surface, the film cooling effectiveness near the injection hole decreased as the divergent angle increases. However, the film cooling effectiveness at far downstream from the hole showed opposite trend. For the non-film cooled surface inclined case, the film cooling effectiveness was not much affected by the divergent angle.

• 융복합기술연구소 논문집
• /
• 제5권1호
• /
• pp.27-31
• /
• 2015

A Pin-fin array is widely used to enhance the heat transfer in the internal cooling passage. The heat transfer distribution around the pin-fin is varied by the horseshoe vortex and flow separation. The difference of heat transfer coefficient induces the large thermal stress, which is one of the major reasons to break of hot components. So, it is required to enhance the heat transfer on the back side of pin-fin to solve the thermal stress problem. This study suggests the pin-fin with inclined jet hole and complex pin-fin/dimple array to enhance the heat transfer on the back side of pin-fin. The heat transfer coefficient is predicted by the numerical analysis, which is performed by CFX 14.0. The numerical results are obtained at Reynolds number, 10,000. The results show that the heat transfer on the back side of pin-fin is increased in both cases. Beside, the wake, which comes from dimple and jet, helps to develop the horseshoe vortex and increase the heat transfer on the next row pin-fin.

• Structural Engineering and Mechanics
• /
• 제74권5호
• /
• pp.601-609
• /
• 2020

In this article, the Strain Energy Density (SED) averaged over a well-defined control volume at a notch edge was applied in combination with the Equivalent Material Concept (EMC) to assess the fracture behaviors of some keyhole-notched specimens made of a High-Density Polyethylene (HDPE-PE80) material under mixed-mode loading conditions. An experimental program was performed and 54 new experimental data were totally provided. Additionally, different loading mode ratios were regarded by changing the inclination angles of the notches with respect to the applied load directions. The results obtained from the determined criteria were in good agreement with those of the experimental data.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 추계학술대회논문집
• /
• pp.102-108
• /
• 1995

Internal contact scheme between two free surfaces on one deforming body has been proposed by using the penalty method. It has been imposed to be internal boundary condition on two-dimensional thermo-viscoplastic finite element method so as to analyze one deforming body, which has two free surfaces penetrating each others. Analysis of side pressing with a circular void and a inclined elliptic hole have been carried out in order to verity the proposed contact scheme. A finite element code imposed internal boundary condition has been applied to two-dimensional analysis of free forging of large ingot with a void. Through the analysis, effects of working parameters in order to consolidate voids have been investigated.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.471-474
• /
• 1996

The effects of injection angles between $0^{\circ}$ and $9^{\circ}$, mainstream turbulent intensities between 0.36 percent and 9.3 percent and embedded longitudinal vortices on jets issuing from a single film cooling hole and from a row of inclined holes are investigated. The heat transfer coefficients around film cooling holes are affected greatly by the compound injection angles. The injected jets affected weakly by the freestream turbulence at low level. However, the heat transfer coefficients near the film cooling holes have higher values at a high turbulence intensity. The vortices generated from a delta winglet change the injected jet direction and the kidney-type vortex pattern.

• 한국추진공학회지
• /
• 제2권2호
• /
• pp.56-63
• /
• 1998

본 논문에서는 주유동의 난류강도 변화에 따른 복합각도로 분사되는 단일 막냉각홀 주위에서의 국소 열/물질전달계수 특성을 살펴보기 위하여 실험을 수행하였다. 단일 막냉각홀 시편은 평면에 대하여 $30^{\cire}$의 경사각을 가지고 있으며, 횡방향으로는 주유동에 대해 $45^{\cire}$의 각도로 분사하여 복합각도 분사시 주유동의 난류강도 변화에 따른 효과를 살펴보았다. 또한 막냉각제트의 분사율을 0.5에서 2.0까지 변화시켜가며, 주유동의 높은 난류강도조건에서 분사율 변화시 막냉각홀 주위의 열/물질전달특성에 미치는 효과를 살펴보았다. 주유동의 난류강도를 변화시키기 위하여 막냉각홀 상류에 난류발생격자를 설치하였다. 격자를 설치하지 않은 경우, 주유동의 난류강도는 0.5%이며, 난류발생격자의 종류 및 설치위치를 달리하여 난류강도를 3%에서 10%까지 변화시켜가며 실험하였다. 막냉각홀 주위에서 국소적인 열/물질전달계수 값을 얻기 위하여 물질전달 실험방법인 나프탈렌 승화법을 사용하였다. 주유동의 난류강도가 낮은 경우 분사홀 주변에서 막냉각제트 혹은 주유동에 의한 열/물질전달 촉진영역이 뚜렷한 경계를 갖지만, 난류강도가 증가하면서 전 영역에 걸쳐 열/물질전달이 촉진되었으며 주유동과 막냉각제트의 활발한 혼합작용으로 인해 영역의 구분이 점차 소멸되었다. 또한 주유동의 높은 난류강도 효과는 막냉각제트의 분사율이 높은 경우 뚜렷이 나타났다.

• 한국해양환경ㆍ에너지학회지
• /
• 제2권1호
• /
• pp.40-48
• /
• 1999

해양공학과 관련된 모형실험을 위하여 많이 사용되고 있는 조파수조(2차원수조, 장수조, 사각수조)에 소파장치는 필수적인 장치이다. 본 논문에서는 새로운 개념의 소파장치의 소파성능을 실험을 통하여 살펴보았다. 새로 고안된 소파장치는 소파성능이 우수하고 가볍기 때문에 설치가 용이하다. 또한 넓은 설치공간이 필요치 않아 수조공간 활용에 있어 효과적이며 조파기로부터 발생된 파장에 큰 영향을 받지 않기 때문에 아주 큰 장파만 피한다면 거의 완벽하게 파를 소멸시킬 수 있는 장점을 가지고 있다. 본 소파장치는 일정한 크기의 구멍이 균일하게 배열된 타공판을 입사파의 진행방향과 수평으로 수면밑에 잠기게 설치한 형태로 파가 수평형 타공판을 통과하면서 타공판의 구멍을 통하여 강한 제트 흐름이 형성되면서 파 에너지가 소멸되는 특징을 가지고 있다. 모형실험 결과 수평형 타공판의 소파성능은 타공판의 잠긴 깊이와 판의 전체면적과 뚫린 부분의 면적의 비로 표현되는 공극율에 밀접한 관련이 있으며, 각각의 값은 최대 소파성능을 발휘하는 최적의 값을 가지고 있음을 규명하였다. 수평형 타공판의 앞쪽을 뒤쪽보다 약간 기울게 설치하는 방법도 특정한 주파수 범위내에서는 수평형에 비하여 우수한 소파성능을 보이며, 이때 타공판의 경사각도도 소파장치 성능을 결정하는데 중요한 변수임을 밝혔다.