• Geomechanics and Engineering
• /
• v.28 no.2
• /
• pp.181-195
• /
• 2022

Roughness and joint inclination angle are the important factors that affect the strength and deformation characteristics of jointed rock mass. In this paper, 3D printer has been employed to make molds firstly, and casting the jointed specimens with different joint roughness coefficient (JRC), and different joint inclination angle (α). Conventional triaxial compression tests were carried out on the jointed specimens, and the influence of JRC on the strength and deformation parameters was analyzed. At the same time, acoustic emission (AE) testing system has been adopted to reveal the AE characteristic of the jointed specimens in the process of triaxial compression. Finally, the morphological of the joint surface was observed by digital three-dimensional video microscopy system, and the relationship between the peak strength and JRC under different confining pressures has been discussed. The results indicate that the existence of joint results in a significant reduction in the strength of the joint specimen, JRC also has great influence on the morphology, quantity and spatial distribution characteristics of cracks. With the increase of JRC, the triaxial compressive strength increase, and the specimen will change from brittle failure to ductile failure.

• Physical Therapy Korea
• /
• v.13 no.2
• /
• pp.16-25
• /
• 2006

The aim of this study was to investigate the kinematics of young adults during descent ramp climbing at different inclinations. Twenty-three subjects descended four steps at four different inclinations (level, $-8^{\circ}$, $-16^{\circ}$, $-24^{\circ}$). The 3-D kinematics were measured by a camera-based Falcon System. The data were analyzed using one-way ANOVA and the Student-Newman-Keuls test. The kinematics of descent ramp walking could be clearly distinguished from the kinematics of level walking. On a sagittal plane, the ankle joint was more plantar flexed at initial contact with $-16^{\circ}/-24^{\circ}$ inclination, was decreased in the toe off position with all inclinations (p<.001),and was decreased at maximum plantar flexion during the swing phase (p<.001). The knee joint was more flexed at initial contact with the $-24^{\circ}$ inclination (p<.001), was more flexed in the toe off position with all inclinations (p<.001), and was more flexed at minimum flexion during stance phase and at maximum flexion during swing phase with $-16^{\circ}$, $-24^{\circ}$ inclination (p<.001). The hip joint was more flexed in the toe off position with $-16^{\circ}$, $-24^{\circ}$ inclination and was deceased at maximum extension during stance phase with $-16^{\circ}$, $-24^{\circ}$ inclination (p<.05). In the frontal plane, the ankle joint was more everted at maximum eversion during stance phase with $-16^{\circ}/-24^{\circ}$ inclination (p<.01) and was decreased at maximum inversion during swing phase with $-16^{\circ}$, $-24^{\circ}$ inclination (p<.01). The knee joint was more increased at maximum varus during stance phase with $-16^{\circ}/-24^{\circ}$ inclination (p<.001). The hip joint was deceased at maximum adduction during stance phase with $-24^{\circ}$ inclination (p<.05). In a horizontal plane, only the knee joint was increased at maximum internal rotation during stance phase with $-24^{\circ}$ inclination (p<.05). In descent ramp walking, the different gait patterns occurred at an inclination of over $16^{\circ}$ on the descending ramp in the sagittal and frontal planes. These results suggest that there is a certain inclination angle or angular range where subjects do switch between level walking and descent ramp walking gait patterns.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.9
• /
• pp.115-125
• /
• 1995

부품가공에 있어서 생산성향상을 위하여 버제거를 위한 고도의 기술이 더욱 중요하게 되었다. 특히 CIM 체제에서는 버제거의 자동화를 위하여 가공중에 발생하는 버형성과 파단현상을 정량적으로 예측할 필요성이 더욱 커졌다. 이미 연구된 2차원절삭에서의 버형성 모델을 실제적인 3차원절삭에 적용하기 위하여 기존의 모델을 수정하는 작업이 이루어졌다. 3차원 절삭모델로는 절삭인선에 수직한 면에서의 칩과 공구의 상대운동에 의해서 결정된다고 하는 Rubenstein의 가정이 사용되었다. 본연구에서 다루에되는 롤오버(roll-over) 버는 항상 공구진행방향으로 발생하기 때문에 3차원절삭에서의 버형성을 공구진행방향의 평면내에서의 2차원 절삭의 집합 으로 가정하였다. 공구의 기울림각(inclination angle)이 커질수록 버형성의 크기나 파단면의 크기가 감소하였다. 두종류의 파단이 버형성중에 관찰되었다. 하나는 가공물 끝면에 평행하게 파단면이 발생하였으며 다른 하나는 이에대하여 기울어진 파단이 일어났다. 가공물 끝면에 평행한 경우는 수정된 모델로부터 등가초기공구위치( equivalent initial tool distance)로부터 예측이 가능하며 기울어진 경우는 이결과와 공구의 기울림각으로부터 파단위치를 예측할 수 있다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.108-109
• /
• 2016

It is very important to fully understand the concepts, causes and corrections of ship's transverse inclination which is classified into Heel, List and Loll. Particularly, it is presumed that some recent disaster at sea is related to negative GM developed by the loss of stability during sailing. In this study, actual 'Angle of Loll' is simulated by model-ship experiment and the result is compared with calculated value under same condition. Furthermore, how to distinguish Loll from List and the way to correct the 'Angle of Loll' for officers are described.

• Journal of Biosystems Engineering
• /
• v.18 no.3
• /
• pp.199-208
• /
• 1993

This study was attempted to develop the eletronic-hydraulic hitch system for controlling the attitude of tractor implements and to investigate control performance of the system through experiments. Main components of the system developed in this study were reference inputs panel, inclination angle detecter, electronic controller consisted of IBM-AT PC and interfaces, electro-hydraulic directional valves and other hydraulic components and three-point hitch linkage. Experiments were carried out to investigate the response of the system to the step and sine inputs. The effects of hydraulic flow rate and dead band on control performance were analized. Attitude of the implement was controlled within 2.4-5.1 degrees to the setting attitude when the hydraulic flow rate was in the range of $0.25-1.5{\ell}/min$. And implement was controlled without rapid amplitude attenuation and phase angle change in the frequency range of 0.02-0.2Hz when the hydraulic flow rate was in the range of $0.25-1.5{\ell}/min$. Control performance of the system can be expected to be improved if the inclination angle detecter show rapid and stable output as the implement moves.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.1
• /
• pp.1-8
• /
• 2017

A new empirical correlation was developed for application to the tandem tubes for saturated water at atmospheric pressure. The correlation was obtained by using experimental data and the least square method to calculate the bundle effect. A statistical analysis was performed to identify the suitability of the correlation. The correlation predicted the experimental data within ${\pm}8%$. The applicable ranges of the correlation correspond to a tube pitch of 28.5~114 mm, an elevation angle of $0^{\circ}{\sim}90^{\circ}$, an inclination angle of $0^{\circ}{\sim}90^{\circ}$, and heat fluxes of $0{\sim}120kW/m^2$ of the lower and upper tubes.

• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.139-144
• /
• 2003

Augmentation of CHF by ultrasonic vibration in water pool is experimentally investigated under pool boiling condition. The experiments are carried out using copper coated plates and distilled water. Measurements of CHF on flat plate heated surface were made with and without ultrasonic wave and with variations in inclined angle of the surface and water subcooling. Experimental apparatus consists of a bath, power supply, test section, ultrasonic generator, and data acquisition system. The measurements show that ultrasonic wave enhances CHF and its extent is dependent upon inclination angle as well as water subcooling. The rate of increase in CHF increases with an increase in water subcooling while it decreases with an increase in inclination angle. Visual observation shows that the cause of CHF augmentation is closely related with the dynamic behavior of bubble generation and departure in acoustic field.

• Journal of Veterinary Clinics
• /
• v.30 no.4
• /
• pp.278-282
• /
• 2013

This study was performed in 41 dogs with unilateral or bilateral medial patella luxation (MPL) and/or cranial cruciate ligament rupture (CCLR). These dogs were classified into 4 groups according to MPL grading system. Radiographic evaluation was performed for pelvis and stifle joint in the dogs. Norberg, inclination, quadriceps and femoral varus angle were measured and analyzed with MPL grading and the existence of cranial cruciate ligament rupture. The Norberg and inclination angle showed no differences between 4 grading groups and between CCLR and no CCLR groups. However, quadriceps and femoral varus angle were statistically different between grade 1, 2 and grade 3, 4 groups. They also have shown the statistical difference between CCLR and no CCLR group. Further studies for how these parameters affect the prognosis and the results of surgical treatment of MPL should be needed.

• Knee surgery & related research
• /
• v.30 no.4
• /
• pp.311-318
• /
• 2018

Purpose: The purpose of this study was to evaluate changes in the coronal alignment of the knee and ankle joints after open wedge high tibial osteotomy (OWHTO) to determine factors related to the recurrence (R) of the varus deformity by serial analysis. Materials and Methods: Sixty-four OWHTOs were enrolled in this study. The weight bearing line (WBL) ratio, joint line convergence angle (JLCA), knee joint inclination, mechanical axis-tibial plateau angle, talar inclination (TI), and distal tibia articular angle (DTAA) were serially assessed. Serial correlation analysis between all parameters was performed. Patients were divided into R group and no recurrence (NR) group according to the WBL ratio (55%) at postoperative one year. Results: The preoperative WBL ratio showed significantly negative correlation with serial changes of JLCA, TI, and DTAA (p<0.05). The JLCA, TI, and DTAA as well as WBL ratio showed a significantly larger degree of varus alignment in the R group than in NR group at postoperative 6 weeks and 1 year after OWHTO (p<0.05). Conclusions: Sufficient correction of the WBL and restoration of the JLCA during OWHTO are essential to prevention of the R of varus deformity after the surgery because they are the only modifiable factors during surgery. Level of Evidence: IV, Case series.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3021-3026
• /
• 2007

In this paper, experimental data on flow pattern transition of inclination angles from 0-90 are presented. A test section is constructed 2 mm long and I.D 1inch using transparent material. The test section is supported by aluminum frame that can be placed with any arbitrary inclined angles. The air-water two-phase flow is observed at room temperature and atmospheric condition using both high speed camera and void impedance meter. The signal is sampled with sampling rate 1kHz and is analyzed under fully-developed condition. Based on experimental data, flow pattern maps are made for various inclination angles. As increasing the inclination angels from 0 to 90, the flow pattern transitions on the plane jg-jf are changed, such as stratified flow to plug flow or slug flow or plug flow to bubbly flow. The transition lines between pattern regimes are moved or sometimes disappeared due to its inclined angle.