• Electrical & Electronic Materials
• /
• v.16 no.9
• /
• pp.65.1-65
• /
• 2003

The interface of zirconium oxide thin films on silicon is analyzed in detail for their potential applications in the microelectronics. The formation of an interfacial layer of ZrSi$\sub$x/O$\sub$y. with graded Zr concentration is observed by the x-ray photoelectron spectroscopy and secondary ion mass spectrometry analysis. The as-deposited ZrO$_2$/ZrSi$\sub$x/O$\sub$y//Si sample is thermally stable up to 880$^{\circ}C$, but is less stable compared to the ZrO$_2$/SiO$_2$/Si samples. Post-deposition annealing in oxygen or ammonia improved the thermal stability of as-deposited ZrO$_2$/ZrSi$\sub$x/O$\sub$y/Si to 925$^{\circ}C$, likely due to the oxidation/nitridation of the interface. The as-deposited film had an equivalent oxide thickness of∼13 nm with a dielectric constant of ∼21 and a leakage current of 3.2${\times}$10e-3 A/$\textrm{cm}^2$ at 1.5V. Upon oxygen or ammonia annealing, the formation of SiO$\sub$x/ and SiH$\sub$x/N$\sub$y/O$\sub$z/ at the interface reduced the overall dielectric constants.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.569-576
• /
• 1997

Electrically-induced strain and polarization studies of the (1-x)Pb(Mg1/3Nb2/3)O3-PbZrO3 crystalline solutions have been done. Dielectric constants with temperature were investigated for 0$\leq$x$\leq$0.95. With increasing PbZrO3 content the transition maxima were found to move to higher temperature region and DPT (Diffused Phase Transition) properties were decreased for x$\leq$0.60. Phase transition between ferroelectric states and antiferroelectric states was confirmed for 0.93$\times$10-3 for 0.4

• Bulletin of the Korean Chemical Society
• /
• v.24 no.3
• /
• pp.311-317
• /
• 2003

Vanadium oxides supported on zirconia and modified with MoO₃were prepared by adding Zr(OH)₄powder into a mixed aqueous solution of ammonium metavanadate and ammonium molybdate followed by drying and calcining at high temperatures. The characterization of prepared catalysts was performed using FTIR, Raman spectroscopy and solid-state $^{51}V$ NMR. In the case of a calcination temperature of 773 K, for samples containing low loading of $V_2O_5$, below 15 wt %, vanadium oxide was in a highly dispersed state, while for samples containing high loading of $V_2O_5$, equal to or above 15 wt %, vanadium oxide was well crystallized because the $V_2O_5$ loading exceeded the formation of a monolayer on the surface of $ZrO_2$. The $ZrV_2O_7$ compound was formed through the reaction of $V_2O_5\;and\;ZrO_2$ at 873 K and the compound decomposed into $V_2O_5\;and\;ZrO_2$ at 1073 K, which were confirmed by FTIR spectroscopy and solid-state $^{51}V$ NMR. IR spectroscopic studies of ammonia adsorbed on $V_2O_5-MoO_3/ZrO_2$ showed the presence of both Lewis and Bronsted acids.

• Korean Journal of Materials Research
• /
• v.24 no.7
• /
• pp.357-362
• /
• 2014

Thermal barrier coatings(TBCs) are being applied in many industrial fields such as thermal power generation, aviation and seasonal fields. $ZrO_2-Y_2O_3$(8%) thermal spray coating powders are commercially used as thermal-barrier coating materials to protect against oxidation and corrosion of heat-resistant alloys at elevated temperatures. Currently, $ZrO_2-Y_2O_3$(8%) thermal-spray powder is made using the industrial co-precipitation process, which is very complex and requires a lot of time. In this study, orthorhombic $ZrO_2$ and $Y_2O_3$ powders were fabricated by mechanical mixing, which is more economical than the co-precipitation process. A tetragonal, yttria-stabilized zirconia(YSZ) coating-layer was produced by plasma spraying, using orthorhombic $ZrO_2-Y_2O_3$(8%) powder. Our experimental results indicate that $ZrO_2-Y_2O_3$(8%) mixed powder can be used economically in industry because it is no longer necessary to make this powder by liquid and gas-phase methods.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.397-403
• /
• 1993

Widely used dielectrics, barium titanate was promising material for ceramic capacitor. It was produced by specific formulation with various dopants-La2O3, ZrO2, SnO2, CaZrO3, CaTiO3, CaSnO3, Bi2O3, and etc.-according to demanded properties of capacitor. In this study, we would examinate the study of dielectric properties and temperatuer characteristics (T.C.) with the amount of Bi2O3. The sample was prepared with [BaTiO3]10＋[BaZrO3, SnO2, La2O3, ZrO2]10 and Bi2O3 varied from 1.0, 1.5, 2.0, 2.5 to 3.0wt%. After milling and mixing for 15hrs, each sample was dried and then pressed at 700kg/$\textrm{cm}^2$ into pellets. Pellets were fired at 131$0^{\circ}C$, for 3hrs in air. As the result of measurements, dielectric constant, break down voltage, and insulation resistance were increased with the amount of Bi2O3, and the resonant frequency was shifted from high frequency to low frequency range. In the case of temperature characteristics, capacitance change rate was symmetrically changed at -$25^{\circ}C$ and ＋85$^{\circ}C$ respectively. Therefore, it is recognized that the temperature characteristics can be moderated with doping Bi2O3 in our study.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.964-965
• /
• 2006

The injection molded Fe sintered bodies were fabricated using two kinds of nano Fe powders, $Fe-5%vol.ZrO_2$ and $Fe-10vol.%ZrO_2$ powders. The relationship between microstructure and mechanical properties depending on the $ZrO_2$ contents and sintering temperature were characterized by SEM and TEM techniques. In the wear test, the $Fe-0vol%ZrO_2$ sintered bodies showed mainly adhesive wear, but in the Fe-5%vol. $ZrO_2$ and Fe-10vol. % $ZrO_2$ composites the main wear behavior showed abrasive wear mode.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.751-755
• /
• 2005

Fibrous $Al_2O_3-(m-ZrO_2)/t-ZrO_2$ composites having core/shell structure were fabricated by multi-extrusion process. The effect o volume fraction between core ($Al_2O_3-(m-ZrO_2)$) and shell ($t-ZrO_2$ was investigated to understand the relationship between microstructure and material properites, in which the volume fractions of core and shell were varied as 40:60, 50:50 and 60:40. The material properties o hardness and bending strength were increased as the volume fraction of core was increased, and their maximum values were about 1320 Hv and 750MPa, respectively. However, as the volume fraction of core increased, the values of relative density and fracture toughness were decreased from 97.1 to $96.5\%$ and from $6.5MPa{\cdot}m^{1/2}$ to $5.7MPa{\cdot}m^{1/2}$, respectively.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.267-275
• /
• 1997

$ZrO_2$ Powder was Prepared by sol-gel process and the adsorption characteristic of cobalt($Co^{2+}$) by $ZrO_2$ adsorbent in high-temperature water was investigated using batch adsorption experiment with a stirred autoclave. The prepared $ZrO_2$ was calcined at $600{\sim}1400^{\circ}C$ and analyzed by X-ray diffractometry, SEM, BET surface area, FT-IR and TG-DTA measurement. The tetragonal Phase of $ZrO_2$ is produced $480^{\circ}C$ from amorphous gel at temperature $480^{\circ}C$. Both tetragonal and monoclinic phase of $ZrO_2$ exist at temperature between $600^{\circ}C$ and $1000^{\circ}C$. At temperature $1200^{\circ}C$, tetragonal to monoclinic phase trasition is occurred. The $Co^{2+}$ adsorption capacity of $ZrO_2$ calcined at $600^{\circ}C$ for 4 hours is 0.16 meq $Co^{2+}/g$ adsorbent in the high temperature at $250^{\circ}C$. The adsorption of $Co^{2+}$ on the $ZrO_2$ adsorbent is irreversible endothermic in the temperature range ($125-175^{\circ}C$). The standard enthalpy change (${\Delta}H^{\circ}$) of $ZrO_2$ calcined at $600^{\circ}C$ for 4 hours is 18 kJ/gmol.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.33-35
• /
• 2011

Films of CrAlN and CrZrN were deposited on a steel substrate by closed field unbalanced magnetron sputtering, and their oxidation behaviors were investigated. CrAlN films consisted of dense, polycrystalline CrN and AlN fine columns. The formed oxides consisted primarily of crystalline $Cr_2O_3$ incorporated with $Al_2O_3$. The oxide layers were thin and compact so as to make CrAlN films more protective than CrN films. In case of CrZrN films, Zr atoms were dissolved in the CrN phase. Zr atoms advantageously refined the columnar structure, reduced the surface roughness, and increased the micro-hardness. However, the addition of Zr did not increased oxidation resistance, mainly because Zr was not a protective element. All the deposited films displayed relatively good oxidation resistance, owing to the formation of the highly protective $Cr_2O_3$ on their surface. The $Cr_{40}Zr_9N$ and $Cr_{31}Zr_{16}N$ films oxidized to $Cr_2O_3$ as the major phase and ${\alpha}-ZrO_2$ as the minor one, whereas the CrN film oxidized to $Cr_2O_3$.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.53-59
• /
• 2014

The corrosion resistance of submerged entry nozzle (SEN) materials were investigated for high-class steel manufacturing. Composite samples were fabricated by mixing $ZrO_2$, $Al_2O_3$, MgO, mullite, spinel, and carbon. The raw materials were mixed with attrition milling, compacted in a uniaxial pressure of 200MPa and calcined at $1000^{\circ}C$ for 3 h in $N_2$ atmosphere. The bulk density and apparent porosity of the calcined samples were measured by the liquid displacement method in water using Archimedes's principle. The corrosion resistance of the samples were measured by cup test with mold powder at $1550^{\circ}C$ for 2 h. The microstructure and elemental analysis of samples were observed by scanning electron microscopy (SEM), energy dispersive spectrum (EDS), and X-ray diffraction pattern (XRD). The XRD result shows that the starting raw materials were crystalline phase. The microstructure of fabricated specimen was investigated before and after corrosion tests at $1000^{\circ}C$ and $1550^{\circ}C$ for 2h. $ZrO_2$-C composite showed good resistance in the slag corrosion test. Among the composite oxide materials, $ZrO_2-Al_2O_3$-C and $ZrO_2$-MgO-C showed better resistance than $ZrO_2$-C in the slag corrosion test. The diameter variation index of $ZrO_2$-C refractory was 16.1 at $1000^{\circ}C$ for 2 h. The diameter variation index of the $ZrO_2-Al_2O_3$-C refractory was larger than that of the $ZrO_2$-C refractory at $1550^{\circ}C$ for 2 h.