• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.11 no.2
• /
• pp.49-67
• /
• 2006

A mesocosm, an artificial tidal flat ecosystem, was constructed outdoors to simulate in situ physical and biochemical environmental conditions of natural tidal flat as much as possible. During the experiment from February to August 2004, the study was focused on the biogeochemical variations of superficial water and porewater after introduction of freshwater into the mesocosm. The mesocosm has three experimental conditions; SW-M-T: maintaining the saline water of approximately 20 psu; FW-M-T: complete exchange of freshwater ul the mesocosm with continuous mixing of water column: FW-NM-T: complete exchange of saline water to freshwater in the mesocosm without mixing of water column. Mass extinction of benthic macrofauna appeared due to drastic decrease of porewater salinity from 20 psu to less than 10 psu between the 63th and 91st day of freshwater introduction in FW-M-T and FW-NM-T. Throughout the periods, 7/8 of bivalves and 2/3 of polychaete populations have been extinguished in the sediment. In FW-NM-T, as temperature rises, both evident decrease of DO in water column and active release of DIP from sediment were observed. ${NO_3}^-$ was removed from water column into sediment throughout the periods. Therefore extremely low ${NO_3}^-$ was found during late spring and summer. Whereas ${NH_4}^+$ exhibited only $1/2{\sim}1/8$ of ${NO_3}^-$ concentration. Unexpectedly even after mass extinction of benthic macrofauna, we were not able to find high ${NH_4}^+$. This mesocosm study suggests that when fresh water introduce to natural tidal flat, its sediment activity functions as a potential source of DIP, but a sink of ${NO_3}^-$.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.1
• /
• pp.51-62
• /
• 2020

This study was conducted to develop a method for depth assessment of embedded sources using gamma-spectrum ratio and for the evaluation of field applicability. To this end, Peak to Compton and Peak to valley ratio changes were evaluated according to ¹³⁷Cs, ⁶⁰Co, ¹⁵²Eu point source depth using HPGe detector and MCNP simulation. The effects of measurement distance of PTV and PTC methods were evaluated. Using the results, the source depth assessment equation using the PTC and PTV methods was derived based on the detection distance of 50 cm. In addition, the sensitivity of detection distance changes was assessed when using PTV and PTC methods, and error increased by 3 to 4 cm when detection distance decreased by 20 cm based on 50 cm. However, it was confirmed that if the detection distance was increased to 100 cm, the effects of detection distance were small. And PTV and PTC methods were compared with the two distance measurement method which evaluates the depth of source by the change of net peak counting rate according to the detection distance. As a result of source depth assessment, the PTV and PTC showed a maximum error of 1.87 cm and the two distance measurement method showed maximum error of 2.69 cm. The results of the experiment confirmed that the accuracy of the PTV and PTC methods was higher than two distance measurement. In addition, Sensitivity evaluation by horizontal position error of source has maximum error of less than 25.59 cm for the two distance measurement method. On the other hand, PTV and PTC method showed high accuracy with maximum error of less than 8.04 cm. In addition, the PTC method has lowest standard deviation for the same time measurement, which is expected to enable rapid measurement.

• Korean Journal of Remote Sensing
• /
• v.36 no.6_1
• /
• pp.1465-1483
• /
• 2020

Evapotranspiration is a concept that includes the evaporation from soil and the transpiration from the plant leaf. It is an essential factor for monitoring water balance, drought, crop growth, and climate change. Actual evapotranspiration (AET) corresponds to the consumption of water from the land surface and the necessary amount of water for the land surface. Because the AET is derived from multiplying the crop coefficient by the reference evapotranspiration (ET0), an accurate calculation of the ET0 is required for the AET. To date, many efforts have been made for gridded ET0 to provide multiple products now. This study presents a comparison between the ET0 products such as FAO56-PM, LDAPS, PKNU-NMSC, and MODIS to find out which one is more suitable for the local-scale hydrological and agricultural applications in Korea, where the heterogeneity of the land surface is critical. In the experiment for the period between 2016 and 2019, the daily and 8-day products were compared with the in-situ observations by KMA. The analyses according to the station, year, month, and time-series showed that the PKNU-NMSC product with a successful optimization for Korea was superior to the others, yielding stable accuracy irrespective of space and time. Also, this paper showed the intrinsic characteristics of the FAO56-PM, LDAPS, and MODIS ET0 products that could be informative for other researchers.

• Journal of Conservation Science
• /
• v.25 no.1
• /
• pp.101-114
• /
• 2009

Potsherds and kilns of the AD 3th century excavated from Gundong and Majeon sites, Korea were studied to investigate the production techniques and provenance of potsherds and kilns on the pastes. For potsherds, kilns blocks and in-situ paleo-soils, provenance of raw materials were estimated through mineralogy and geochemistry, while production technique and thermal feature of kilns were investigated through observation of textures and compositions as well as firing experiment on paleo-soils. As a result of study, potsherds and kilns were found to have similar mineralogical compositions as the neighboring paleo-soils and to have same evolution path with that of geochemistry. The potsherds were divided into 3 groups according to firing temperature and production technique. Group 1 consists of reddish stamped pattern pottery with loose textures, which has many pores and contains many iron oxides. Its temper is less than about 0.5mm, and was probably fired between 700 to $800^{\circ}C$. Group 2 contains ash to grayish blue stamped pattern pottery, which has vitrified texture and few pores. Its temper is less than about 0.5mm, and was probably fired from 900 to $1,000^{\circ}C$. However, some potsherd belongs to the group 2 in terms of features for temper and pastes, but it was probably fired over $1,100^{\circ}C$. Group 3 contains reddish and grayish stamped pattern pottery. It has vitrified matrix, few pores and temper consists of polycrystalline quartz and feldspar over 2mm, and it was probably fired around $1,000^{\circ}C$. The kiln had experienced temperature from 600 to $700^{\circ}C$ on the wall, from 900 to $1,000^{\circ}C$ on the bottom, suggesting the function of high temperature firing.