• Journal of computational fluids engineering
• /
• v.15 no.3
• /
• pp.16-23
• /
• 2010

Shape optimization of an upper plenum of a PBMR type gas cooled nuclear reactor has been performed by using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) analysis and surrogate modeling technique. The objective function is defined as a linear combination of uniformity of flow distribution in the core and pressure drop in the upper plenum and the core. The ratio of thickness of slot to diameter of rising channels, ratio of height of upper plenum to diameter of rising channels, and ratio of height of the slot at inlet to outlet, are used as design variables for optimization. Design points are selected through Latin-hypercube sampling. The optimal point is determined through surrogate-based optimization method which uses 3-D RANS analyses at design points. The results show that the optimum shape represent remarkably improved performance in flow uniformity and friction loss than the reference shape.

• Journal of ILASS-Korea
• /
• v.22 no.3
• /
• pp.116-121
• /
• 2017

Pre-combustion chamber type indirect diesel engines have different combustion characteristics compared with those of common rail direct injection engine. The CONVERGE, specific engine CFD program, was used to simulate hollow cone spray model and combustion. The air-fuel mixture flow propagating from pre-combustion chamber to cylinder was concentrated at top half and center of the pre-combustion chamber throat. Stronger mixture flow was formed at smaller and longer throat cases. As a result, thermal efficiency and fuel consumption were improved for modified throat shape and the soot emission was also reduced.

• Journal of Applied Reliability
• /
• v.11 no.1
• /
• pp.31-41
• /
• 2011

A strut mount is an important part of vehicles which reduces the vibration and the impact transmitted from the wheels while supporting a shock absorber and a coil spring. Rubber compounding, shape design, and process design technologies are important components to improve the functionality of a strut mount such as durability, static, dynamic, and torsional characteristics. Among them the rubber compounding technology is the key technology which dominates the quality of a strut mount. In this study a strut mount with high reliability has been developed by adopting new rubber compounding and improving the shape of the inner plate and the isolator. Through the tests for prototypes it has been shown that the durability has been improved more than 2.5 times, from about 60,000 cycles to about 160,000 cycles.

• Transactions of Materials Processing
• /
• v.14 no.2 s.74
• /
• pp.153-159
• /
• 2005

Design modification of the stamping die for the upper member of a front end module carrier is carried out in order to improve the surface quality of the final product. The small inferiority induced by wrinkling near the wall of the upper member has been inspected after the draw-forming process. The finite element analysis is pursued with the whole geometry in order to consider the complicated shape. The simulation shows that the excess metal is developed by the irregular contact of the blank the tool and it remains after the final stroke. This paper proposes two guidelines for the modification. One is to add the draw-bead near the critical region in order to increase the draw-in force. The other is to modify the tool shape such as the forming shape at the wall in order to absorb the excess metal before the final stroke. Simulation results show that the proposed guidelines both guarantee the improved surface quality.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.40-45
• /
• 2003

The high-speed rotating arc process forms a flat bead surface with decreased penetration depth because the molten droplets are deflected by centrifugal force. Therefore the rotating arc welding for horizontal fillet welding increases the leg length with the increase of rotation frequency and prevents the deflection of weld bead and overlap. In this study, the relationship between the welding parameters and the weld bead shape - leg length and undercut - are investigated experimentally. Consequently, the weld quality could be improved by rotating arc welding, and sound weld bead was achieved when applied to horizontal fillet welding with 4mm gap by avoiding the undercut which is inevitable for the conventional GMA welding methods.

• Structural Monitoring and Maintenance
• /
• v.1 no.3
• /
• pp.309-322
• /
• 2014

Detection of fatigue cracks at an early stage of their development is important in structural health monitoring. The breathing of cracks in a structure generates higher harmonic components of the exciting frequency in the frequency spectrum. Previously, the residual operational deflection shape (R-ODS) method was successfully applied to beams with a single crack. The method is based on the ODSs at the exciting frequency and its higher harmonic components which consider both amplitude and phase information of responses to map the deflection pattern of structures. Although the R-ODS method shows the location of a single crack clearly, its identification for the location of multiple cracks in a structure is not always obvious. Therefore, an improvement to the R-ODS method is presented here to make the identification process distinct for the beams with multiple cracks. Numerical and experimental examples are utilised to investigate the effectiveness of the improved method.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.2
• /
• pp.74-80
• /
• 1998

An extensive corrosion study was initiated by galvalume steel sheet manufacturing company to clarify the corrosion behavior of zinc and zinc-alloy coated automotive sheet steel in out panel and electrical application. Since the early 1980's the use of zinc and aluminum alloy coated steel for vehicular corrosion protection has increased drastically. This paper describes the evaluation of formability, weldability and painted corrosion performance of galvalume steel sheet. This paper presents an overview of the program and some initial test results on the weldability, lifetime of the electrode tip shape of the spot welding and corrosion protection. Galvalume steel sheet improved corrosion performance and spot weldability of galvalume steel sheet has no problem for the variation of welding current. And tip lifetime was changed according to the influence of shape.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.10a
• /
• pp.12-17
• /
• 1995

The purpose of this study si the development of a lathe which can cut any pistons of oval shape with high seed, accuracy and precision by CNC (Computer Numerical Control) method. Yaxis which is the position determinating mechanism with high speed response was added to the CNC lathe and the ovality and profile was cut under the control of C-Y-Z axes at same tile. In the case of ovality of $\Phi$ improved up to 2500rpm(Y axis : 83Hz) by high speed cutting than modeling method. Since a personal computer is used, it is easy to change the shape of piston and can be applied promptly to many types of piston shape by only changing data files.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1255-1258
• /
• 2008

Roll to roll (R2R) system, known as 'web processing', is the process of producing these electronic devices on a roll of flexible plastic. With the need of improved performance and productivity in R2R industry, effective control and on-line supervision for web quality is essential. In this report, we present a system for on-line measurement of wrinkles, one of defects incurring due to compressive stresses developed in the web. This system is able to capture an image generated when a well defined line shape laser beam passes through a transparent web. The system calculates 3D shape information, including the height of the wrinkle on the web, and displays the images for the shape information of the web in real time. By using area scan camera and machine vision laser, this system takes more advantages of setting up as a simple and low cost system compared to the line scan camera systems that widely used in web manufacturing. Specific calibration method and analysis on the achievable accuracy will be discussed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.3 s.18
• /
• pp.69-76
• /
• 2004

In this paper, an efficient inverse design method for nose shape of submerged body based on the MGM(Modified Garabedian-McFadden) design method has been developed. The MGM design method is a residual-correction technique, in which the residuals are differences between the desired and the computed pressure distributions. 3-D incompressible Wavier-Stokes equation was adopted for obtaining the surface pressure distribution and combined with the MGM design method to perform the inverse design of nose shape of submerged body. The design method was verified by applying to several airfoil shapes. Improved design shapes could be obtained when the method was applied to nose shapes of submerged body.