• 한국산학기술학회논문지
• /
• 제12권11호
• /
• pp.5370-5375
• /
• 2011

활성탄소섬유에 항균특성을 부가하기 위해 은나노입자, 망간 그리고 인산을 첨착시켰으며 이러한 첨착정도를 SEM 분석을 통해 관찰한 결과 적절하게 ACF에 첨착되었음을 확인할 수 있었다. 은나노입자 등으로 첨착된 ACF는 첨착되지 않은 ACF보다 휘발성 유기화합물의 흡착능력면에서 다소 떨어짐을 알 수 있었다. 은나노입자와 인산으로 첨착된 ACF의 경우 bacillus cereus와 salmonella entaritidis에 대해 뛰어난 항균력을 보였으나 망간으로 첨착된 ACF의 경우는 bacillus cereus와 salmonella entaritidis에 대한 항균력이 거의 없음을 알 수 있었다.

• Carbon letters
• /
• 제5권4호
• /
• pp.180-185
• /
• 2004

Thermolysis of $Cu(NO_3)_2{\cdot}3H_2O$ impregnated activated carbon fiber (ACF) was studied by means of XRD analysis to obtain Cu-impregnated ACF. $Cu(NO_3)_2{\cdot}3H_2O$ was converted into $Cu_2O$ around $230^{\circ}C$. The $Cu_2O$ was reduced to Cu at $400^{\circ}C$, resulting in ACF-C(Cu). Some Cu particles have a tendency to aggregate through the heat treatment, resulting in the ununiform distribution in ACF. Catalytic decomposition of NO gas has been performed by Cu-impregnated ACF in a column reactor at $400^{\circ}C$. Initial NO concentration was 1300 ppm diluted in helium gas. NO gas was effectively decomposed by 5~10 wt% Cu-impregnated ACF at $400^{\circ}C$. The concentration of NO was maintained less than 200 ppm for 6 hours in this system. The ACF-C(Cu) deoxidized NO to $N_2$ and was reduced to ACF-$C(Cu_2O)$ in the initial stage. The ACF-$C(Cu_2O)$ also deoxidized NO to $N_2$ and reduced to ACF-C(CuO). This ACF-C(CuO) was converted again into ACF-C(Cu) by heating. There was no consumption of ACF in mass during thermolysis and catalytic decomposition of NO to $N_2$ by copper. The catalytic decomposition was accelerated with increase of the reaction temperature.

• 한국안전학회지
• /
• 제14권3호
• /
• pp.127-133
• /
• 1999

One of the major malodorous gas at the working place is hydrogen sulfide and impregnated activated carbon fiber(ACF) was used as a adsorbent to remove this gas. ACF is treated and impregnated with chemicals to increase the adsorption capacity. The experiments showed that the adsorption efficiency for hydrogen sulfide was increased in case of impregnation with $Na_2CO_3$ or KI. Also, by the surface treatment with NaOH, the adsorption efficiency was increased however not so much as impregnation. KI was the best impregnant for this purpose and the optimum concentration was 9wt%. The adsorption capacity of hydrogen sulfide was more than 500mg/g ACF.

• 공업화학
• /
• 제17권5호
• /
• pp.532-538
• /
• 2006

탄화 및 활성화 조건을 매개체로 여러 등급의 Polyacrylonitrile (PAN)계 ACF (ACF : Activated Carbon Fiber)를 제조하여 최적의 비표면적을 나타내는 활성화 공정을 알아보았고, 가장 큰 비표면적을 갖는 PAN계 ACF에 대한 표면특성 및 독성가스 등에 대한 흡착특성을 분석하였다. 시험결과 활성화 온도가 증가할수록 비표면적이 증가하고 탄화 온도가 감소할수록 비표면적이 감소하였고, $900^{\circ}C$로 15 min간 탄화한 후 $900^{\circ}C$로 30 min간 활성화 공정을 거친 ACF가 $1204m^2/g$의 가장 높은 비표면적을 나타내었고 요오드 및 테러용 독성가스에 대한 흡착 성능시험 결과 기존의 흡착제보다 우수하였다. 또한 선택적 흡착을 위한 기능성을 부여하기 위하여 기존의 금속염을 침적하는 방법을 대체하여 비교적 안정화된 금속나노입자(Ag, Pt, Cu, Pd)를 제조하여 첨착하였고 이에 대한 표면특성 및 $SO_{2}$에 대한 흡착특성을 분석하였다. 금속나노입자 첨착 ACF에 대한 $SO_{2}$ 흡착성능 시험결과 Ag, Pt, Cu 나노입자를 첨착한 ACF는 무첨착 ACF의 파과시간(326 sec)과 비교 할 때 크게 변함이 없었으나 Pd 나노입자를 첨착한 ACF는 파과시간이 925 sec로 $SO_{2}$ 흡착성능이 매우 우수함을 알 수 있었다.

• 한국안전학회지
• /
• 제13권1호
• /
• pp.92-97
• /
• 1998

Malodorous gases give discomfort and harm to laborers and residential neighborhoods and therefore, the removing odor materials emitted from plants and industrial facilities is important subject. The main ingredients of alkali odor are $NH_3$ and $CE_3SH$. The adsorption characteristics of odors were studied using four different activated carbon fibers(ACF) and active carbon(AC). Alkali odor was removed by using ACF impregnated with $H_3PO_4$ and $H_2SO_4$ and treated with $HNO_3$ and NaOH. The experimental result showed that ACF has a higher removal efficiency than AC. The adsorption capacity was increased with the impregnation and surface treatment, and $H_2SO_4$ was the best impregnant for the removal of alkali odor.

• 공업화학
• /
• 제18권5호
• /
• pp.467-474
• /
• 2007

팔라듐과 금 나노입자 등이 첨착된 높은 비표면적을 갖는 Polyacrylonitrile (PAN)계 활성탄소섬유(ACF: Activated Carbon Fiber)를 제조하였다. 여러 첨착 ACF에 대하여 BET, FE-SEM, TEM, XPS 등으로 비표면적과 기공부피, 미세구조, 시간에 따른 산소관능기의 표면변화를 관찰하였으며 $SO_2$에 대한 흡착성능을 연구하였다. 그 결과 첨착과정으로 인하여 총 기공부피 대비 미세기공 부피는 95.5%에서 30.5~43.7%로 대부분 감소하였으며, 산소관능기의 표면변화는 대기중에서 시간이 경과함에 따라 나노입자보다 금속염의 산소관능기 변화가 컸음을 알 수 있었다. 또한 Au 나노입자와 금속염을 첨착한 ACF의 $SO_2$ 파과시간은 무첨착 ACF에 비하여 크게 변하지 않았으나, 100 ppm의 Pd 나노입자를 첨착한 ACF는 $SO_2$ 파과시간이 880 s로 흡착성능이 우수하였다. 이러한 결과로 볼 때 $SO_2$ 흡착성능은 시간에 따른 산소관능기의 표면 변화와 연관성이 있다고 볼 수 있으며, PAN계 활성탄소섬유에 적정한 농도의 Pd 나노입자 첨착은 촉매작용으로 인하여 $SO_2$ 흡착 성능을 증가시키는 것으로 판단된다

• Carbon letters
• /
• 제15권1호
• /
• pp.45-49
• /
• 2014

In this study, synthetic viscose rayon fabric has been used for preparing activated carbon fabric (ACF), impregnated with different concentrations of $H_3PO_4$. The effect of $H_3PO_4$ impregnation on the weight yield, surface area, pore volume, chemical composition and morphology of ACF were studied. Experimental results revealed that both Brunauer-Emmett-Teller surface area and micropore volume increased with increasing $H_3PO_4$ concentration; however, the weight yield and microporosity (%) decreased. It was observed that samples impregnated at $70^{\circ}C$ (AC-70) give higher yield and higher microporosity as compared to $30^{\circ}C$ (AC-30). The average pore size of the ACF also gradually increases from 18.2 to 19 and 16.7 to $20.4{\AA}$ for $30^{\circ}C$ and $70^{\circ}C$, respectively. The pore size distribution of ACF was also studied. It is also concluded that the final ACF strength is dependent on the concentration of impregnant.

• Carbon letters
• /
• 제11권2호
• /
• pp.131-136
• /
• 2010

Propellant waste was impregnated on the surface of activated carbon fiber and heat-treated at different temperature to introduce newly developed functional groups on the ACF surface. Functional groups of nitrogen and oxygen such as pyridine, pyridone, pyrrol, lacton and carboxyl were newly introduced on the surface of modified activated carbon fiber. The porosity, specific surface area, and morphology of those modified ACFs were changed as increasing the heat-treated temperature from 200 to $500^{\circ}C$. The optimum heat-treatment temperature was suggested to $500^{\circ}C$, because lower temperature given rise to the decrease of specific surface area and higher temperature resulted in the decrease of weight loss. Propellant waste can be used as an useful surface modifier to porous carbons.

• 한국수소및신에너지학회논문집
• /
• 제17권1호
• /
• pp.47-54
• /
• 2006

Activated carbon fibers (ACFs) with high surface area and pore volume were modified with metal Ni impregnation and fluorination and investigated hydrogen storage properties by volumetric method. Micropore volume values of ACFs obtained from surface modification with Ni impregnation and fluorination were decreased 9 and 35 %, respectively. Hydrogen storage capacities of fluorinated ACFs were slightly changed, on the other hand, that of Ni impregnated ACF was considerably increased. It means that hydrogen was not only adsorbed on ACF surface, but also on Ni metal surface by means of dissociation. Although the microphone volume of ACF modified with fluorination was decreased, its hydrogen storage were found not to be changed compared with fresh ACF. These results indicated that the surface of ACF after fluorination modification may be strongly attracted hydrogen due to high electronegativity of fluorine. Therefore, it was proven that hydrogen storage capacity was related with micropore volume and surface property of carbon materials as well as specific surface area.

• Carbon letters
• /
• 제6권4호
• /
• pp.248-254
• /
• 2005

Silver impregnated activated carbon fibers were post-modified using hydrochloric acid. Adsorption behaviors, SEM morphologies, and functional groups for the silver impregnated ACFs were compared with those of post-modified ACFs. Adsorption isotherms were used to characterize $S_{BET}$, the pore structure and volume of silver-activated carbon fibers (ACFs) before and after acid post-treatment. In order to the reveal the causes of the differences surface states after the samples were washed with hydrochloric acid, outer surface and pore structure were investigated by SEM. And the type and quality of various functional groups were studied from FT-IR spectra and Boehm titration method. Finally, the quantitative properties in silver contents were also examined by EDX spectra.