• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1824-1832
• /
• 1992

This study investigated the compressive Young's modulus and the impactinduced damage of CFRP angle-ply laminate under same impact energy condition. The specimens of angle-ply laminate composites [0.deg.$_{6}$/ .theta..deg.$_{10}$/ 0.deg.$_{6}$] with .theta..deg. =30.deg., 45.deg., 60.deg. and 90.deg. were employed, and damaged by steel balls of diameter of 5mm and 10mm propelled by air gun type impact testing machine. The impact damaged zones were observed through a scanning acoustic microscope(SAM), and their cross-sections were observed through a scanning electron microscope(SEM). The compressive Young's moduli before and after impact were measured, and compared with the theoretical values calculated. The results obtained were as follows: (1) The damage areas on the interfacial boundaries showed more severe change on the back side interface than on the impact side interface with increasing ply-angle. (2) The damage areas on the interfacial boundaries became larger with increasing impact velocity or ply-angle. (3) The impact damaged zone showed the delamination on the interfacial boundaries and transverse cracks inside laminas. (4) The impact damaged zone was affected by the impactor size and speed or ply-angle under same impact energy condition. (5) Compressive Young's moduli before and after impact were lower than theoretical value, but showed a similar change according to ply-angle. (6) Compressive Young's moduli after impact were higher than those before impact, but there was no remarkable change in apparent compressive modulus after impact.t.act.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.76-81
• /
• 2015

Swirl flow has an impact on the stabilization of the flame by the recirculation flow, improvement of the combustion efficiency. The swirl flow in the gun type burner is created by the spinner which is inside the airtube that guide the combustion air. Burner has generally the combustion device composed electronic spark plug, injection nozzle, combustion device adaptor, and spinner. These inner components change the air flow behavior passing through airtube. So, this study analyzed exhaust flow characteristics of the gun type burner according to the ratio of airtube diameter. Turbulence characteristics by the spinner was mean velocity, turbulence intensity, kinetic energy, shear stress and flattness factor of the air flow of axial direction and tangential direction from the exit of the airtube.

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.58-63
• /
• 2016

This study presents the dynamic characteristics of an impinging droplet on hydrophobic and hydrophilic surfaces with various texture area fractions. The flat surface was fabricated by using the drilling technique to make micro-meter hole-patterned surfaces, which shows hydrophobic textured surfaces. Moreover, the hydrophilic textured surfaces were manufactured by anodizing technique on the micro-meter hole-patterned surfaces to generate multi-layer surfaces. Impinging droplet experiments were conducted for various hole-patterned surfaces, with changing impact velocity and texture area fractions. It is observed that an anodizing technique increases wettability by decrease in hole diameter on the textured surfaces. However, micro-drilled surfaces decreases wettability because the hole diameter was so large that air can be trapped under the holes. In addition, the maximum spreading diameter decreases with the texture area fraction for the micro-drilled surfaces because of decrease in wettability.

• Journal of Environmental Impact Assessment
• /
• v.4 no.2
• /
• pp.71-91
• /
• 1995

In order to develop an appropriate set of criteria applicable for environmental impact assessment (EIA) of natural forest 8 items are proposed. The criteria are vegetation distribution area (DA), distribution pattern (DP), size (S), diameter of breast height of tree (DBH), humus (H), sustainment (ST), successional stage (SS) and impact of adjacent ecosystem (IAE), Each criterion has an interval which minimum 1 score to maximum 5 score Forest Evaluation Index (FEI) was obtained as the sum of 8 criteria value. Above 70% is considered to be absolutely conservative and from 50% to 70% range of total score is to be considered conservative. In the case of the Sancho˘ng Pumping-up Power Plant of Mt. Chiri, 8 criteria were applied base on actual vegetation map. Pinus densiflora community got 73%(29 scores) and Quercus variabilis - Q. serrata community got 60%(24 scores). This may be said that this local vegetation has high ecological potentiality. These criteria cannot always be absolutely evaluation tool. So it is expected to take the more time to be developed further, and holistically added by the other field such as fauna, geological feature etc.

• Computers and Concrete
• /
• v.20 no.6
• /
• pp.711-718
• /
• 2017

Nanotechnology is a new filed in concrete structures which can improve the mechanical properties of them in confronting to impact and blast. However, in this paper, a mathematical model is introduced for the concrete models subjected to impact load for wave propagation analysis. The structure is simulated by the sinusoidal shear deformation theory (SSDT) and the governing equations of the concrete model are derived by energy method and Hamilton's principle. The silicon dioxide ($SiO_2$) nanoparticles are used as reinforcement for the concrete model where the characteristics of the equivalent composite are determined using Mori-Tanaka approach. An exact solution is applied for obtaining the maximum velocity of the model. In order to validate the theoretical results, three square models with different impact point and Geophone situations are tested experimentally. The effect of different parameters such as $SiO_2$ nanoparticles volume percent, situation of the impact, length, width and thickness of the model as well as velocity, diameter and height of impactor are shown on the maximum velocity of the model. Results indicate that the theoretical and experimental dates are in a close agreement with each other. In addition, using from $SiO_2$ nanoparticles leads to increase in the stiffness and consequently maximum velocity of the model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.8
• /
• pp.93-98
• /
• 2022

Adiabatic blanking is a method to improve productivity through an autocatalytic cycle that occurs repeatedly through plastic deformation and thermal softening caused by impact energy. In this study, an axisymmetric analysis model comprising a punch, die, holder, and specimen was developed to confirm the temperature and deformation characteristics caused by an impact load. Through this, the impact energy, diameter of the punch, gap between the punch and die, and the effect of the fillet were analyzed. Because this process occurs in a very short time, adiabatic analysis can be performed using the explicit time-integration method. The analysis, confirmed that it is necessary to design a structure capable of increasing the local temperature and plastic deformation by controlling the impact energy, working area, gap, and the fillet.

• Journal of the Korea Furniture Society
• /
• v.12 no.2
• /
• pp.19-27
• /
• 2001

This study was carried out to investigate the mechanical properties of woods treated with 30% aqueous solution of PEG 1000. Compressive, bending and shearing strengths were slightly decreased by PEG treatment. Absorbed energy in impact bending did not show any significant differences between untreated and PEG-treated woods.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.237-247
• /
• 1993

Carbon fiber reinforced plastics(CFRP) have gained increased application in aerospace structures because of their specific strength and stiffness, but are sensitive to impact-induced damage. An experimental investigation was carried out to evaluate the impact resistance of CFRP according to the ply angle. The specimens of angle ply laminate composites were employed with [0.deg. $_{6}$/ .deg.$_{10}$/0.deg.$_{6}$], in which 6 kinds of ply angle such as .deg.=15.deg., 30.deg., 45.deg., 60.deg., 75.deg. and 90.deg. were selected. The impact tests were conducted using the air gun type impact testing machine by steel balls of diameter of 5 mm and 10 mm, and impact-induced damages were evaluated under same impact speed of V=60m/s. The impact damaged zones were observed through a scanning acoustic microscope (SAM). The obtained results were summarized as follows: (1) Delaminations on the interfacial boundaries showed th directional characteristics to the fiber directions. The delamination area on the impact side (interface A) was considerably smaller compared to that of the opposite side (interface B). (2) Cracks corresponding to other delaminations than those mentioned in SAM photographs were also seen on the impact damaged zone. (3) The delamination patterns were affected by the ply-angle, the dimensions of the specimen, and the boundary conditions. (4) The impact damaged zone showed zone showed the delamination on the interfacial boundaries, transverse shear cracks of the surface layer, and bending cracks of the bottom layer.r.r.r.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.312-315
• /
• 2002

This paper summarizes the results of a numerical study conducted to analyze the effect of selected process parameters on material flow and thread profile in thread rolling of large diameter blanks. Based on the previous work where a plane strain mode was found to provide a reasonable approximation of the thread rolling process, the effect of varying thread form, friction factor, flow stress, and blank diameter on effective strain and thread height was analyzed using the finite element code DEFORM. This study show that effective strain for flank angle, that blank diameter had important effect on the as-rolled thread while flow stress, friction factor, and crest round of dies had significant impact on effective strain at the thread root and crest and load of thread rolling. While the rate of strain harding was found to have an effect on the crest profile, the results indicate that it is the primary factor responsible for seam formation in rolled threads.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.1
• /
• pp.10-15
• /
• 2011

Recently, renewable energy sources such as wind turbine, solar cell are interested in preventing global warming which is caused by the consumption of fossil fuel. SCM440(H) and SNCM439 have been used in the major components of the wind turbine gear because of excellent mechanical properties. In the present study, the heat treated mechanical properties of SCM440(H) and SNCM439 with 150 mm diameter were compared with those with 25 mm diameter which is generally accepted material for structural application. Heat treated SCM440(H) showed better mechanical properties such as tensile strength, hardness and impact absorbed energy compared with those in SNCM439. Hardenss value between as-quenched and as-quenched followed by tempering showed big difference in SNCM439, however the difference in SCM440(H) was relatively small. Heat treated mechanical properties of the alloys with 25 mm diameter were more uniform value than those with 150 mm diameter.