• Korean Journal of Metals and Materials
• /
• v.48 no.10
• /
• pp.875-883
• /
• 2010

This study assessed the Charpy impact properties of the heat-affected zones (HAZs) of API X80 linepipe steels containing complex oxides. Three types of steel were fabricated by adding Mg and $O_2$ to form complex oxides and their microstructures and Charpy impact properties were investigated. The number of complex oxides increased with the amount of excess Mg and $O_2$ that was included in the steels. Simulated HAZs containing a number of oxides showed a high volume fraction of acicular ferrite (AF) because the oxides acted as nucleation sites for AF, thereby leading to an improvement in the Charpy impact properties. According to a correlation study between the heat input, the volume fraction of the AF, and the Charpy impact properties, ductile fractures occurred predominantly when the fraction of the AF was 20% or higher; moreover, the Charpy absorbed energy was excellent at more than 100 J. These findings suggest that the improvement of the Charpy impact properties of the HAZs was associated with the active nucleation of AF in the oxide-containing steel HAZs.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.773-781
• /
• 2008

As buildings are becoming taller and longer-spanned, the requirements of high-strength and reliable steels are becoming increasingly stringent. Structural steels, however, acquire significantly different mechanical properties when their strength becomes higher. In this study, the mechanical properties, welding characteristics, and conformities of the 600MPa-grade high-strength steel were tested. The 600MPa-grade steel plates exhibited stable criterion strengthvalues and showed low carbon equivalents (${\mathcal{Ceq}}$) and composition (${\mathcal{Pcm}}$) as well as excellent welding hardness. In the tensile strength test, all the specimens were found to have strengths of over 600MPa. In the Sharphy impact test, the impact-absorbed energy of the V-notch specimens was shown to be 47J at the KS limit. Moreover, the maximum hardness of the specimens in the weld-heat-affected zone at a normal temperature was the same as that before welding. Their weld metal properties, however, were found not to be as good as those of high-strength steel. As such, the details of high-strength steel must be determined.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.4
• /
• pp.119-129
• /
• 1994

The aim of the present study is to derive an empirical formula relating the absorbed energy and the cutting length for longitudinally stiffened steel palates which are cut by a wedge, idealizing the ship bottom stiffened platings in groundings. This study is based on the test results and the investigations of some parameters affecting the cutting response, described in Part I. By dimensionless ana1ysis of the test results obtained in a quasi-static loading condition, the energy absorbed while a longitudinally stiffened plate is cut by a wedge is expressed as functions of the cutting length, the yield stress, the equivalent plate thickness and the wedge angle. Also, the dynamic effects are incorporated into the static formula such that the proposed formula can be applied to the impact loading situations. The validity of the proposed formula is checked by comparing with the results obtained by the other existing formulas or by the drop-hammer tests.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.62-66
• /
• 2015

Considering for plants and structure under extreme conditions is required for the successful design, especially temperature and pressure. The ductile-brittle transition temperature (DBTT) for the materials under extreme condition needs to be considered. In this study, A-grade mild steel for the LNG carrier and offshore plant was examined by performing low-temperature Charpy V-notch (CVN) impact tests to investigate DBTT and the fracture toughness. The absorbed energy decreased gradually with the experimental temperature, which showed an upper-shelf energy region, lower shelf energy region, and transition temperature indicating DBTT. In addition, the fracture surface morphologies of the mild steels indicated ductile fractures at the upper-shelf energy level, with wide and large-sized dimples, whereas a brittle fracture surface, where was observed at the lower-shelf energy level, with both large and small cleavage facets. Based on the experimental results, ductile brittle transition temperature was estimated in about $-60^{\circ}C$.

• Computers and Concrete
• /
• v.22 no.3
• /
• pp.337-353
• /
• 2018

The present study focuses on examining the structural behaviour of steel-fibre-reinforced concrete (SFRC) beams under high rates of loading largely associated with impact problems. Fibres are added to the concrete mix to enhance ductility and energy absorption, which is important for impact-resistant design. A simple, yet practical non-linear finite-element analysis (NLFEA) model was used in the present study. Experimental static and impact tests were also carried out on beams spanning 1.3 meter with weights dropped from heights of 1.5 m and 2.5 m, respectively. The numerical model realistically describes the fully-brittle tensile behaviour of plain concrete as well as the contribution of steel fibres to the post-cracking response (the latter was allowed for by conveniently adjusting the constitutive relations for plain concrete, mainly in uniaxial tension). Suitable material relations (describing compression, tension and shear) were selected for SFRC and incorporated into ABAQUS software Brittle Cracking concrete model. A more complex model (i.e., the Damaged Plasticity concrete model in ABAQUS) was also considered and it was found that the seemingly simple (but fundamental) Brittle Cracking model yielded reliable results. Published data obtained from drop-weight experimental tests on RC and SFRC beams indicates that there is an increase in the maximum load recorded (compared to the corresponding static one) and a reduction in the portion of the beam span reacting to the impact load. However, there is considerable scatter and the specimens were often tested to complete destruction and thus yielding post-failure characteristics of little design value and making it difficult to pinpoint the actual load-carrying capacity and identify the associated true ultimate limit state (ULS). To address this, dynamic NLFEA was employed and the impact load applied was reduced gradually and applied in pulses to pinpoint the actual failure point. Different case studies were considered covering impact loading responses at both the material and structural levels as well as comparisons between RC and SFRC specimens. Steel fibres were found to increase the load-carrying capacity and deformability by offering better control over the cracking process concrete undergoes and allowing the impact energy to be absorbed more effectively compared to conventional RC members. This is useful for impact-resistant design of SFRC beams.

• Korean Journal of Materials Research
• /
• v.14 no.1
• /
• pp.19-27
• /
• 2004

Metallurgical and mechanical experiments were performed to explain unexpected surface cracks encountered in fabricating ground rolled-billet of Fe-Cr-Al alloys at room temperature. The toughness of these alloys containing between 220 and 236 ppm (C+N) has been assessed using notched-bar impact tests. According to our results, with a larger grain size, a higher interstitial content of (C+N) or a smaller size of precipitates, ductile to brittle temperature(DBTT) increased and absorbed energy decreased at room temperature. These results suggest that the surface cracks at room temperature stem from a poor resistance to brittle fracture, due to dislocation movement by the finely dispersed carbides within grains under the condition of higher (C+N) content.

• Journal of Biosystems Engineering
• /
• v.13 no.4
• /
• pp.20-29
• /
• 1988

Properties of agricultural products are important for engineering design and analysis with respect to their mechanical harvesting, handling, transporting and processing. Researcher have presented the data of properties for various kinds of agricultural products. These data, however, are obtained from the materials produced in foreign countries, and a very few data could be found in Korea. In this paper, emphasis put on the importance of measuring the properties of agricultural products through an extensive review of literatures, and some experimental results on the viscoelastic and elastic properties of the materials are presented. Viscoelastic characteristics of some agricultural materials, specifically the force-deformation-time relationship of the whole orange and cylindrical samples of cheese under different types of loading were investigated. In elastic test, the response of apple during an impact and the relationships among various parameters such u degree of damage, drop height and absorbed energy were determined.

• Journal of Korea Foundry Society
• /
• v.21 no.5
• /
• pp.296-303
• /
• 2001

The effects of the revolution speed on the mechanical properties and microstructure of Cr-Mo steel during vertical centrifugal casting using investment mold were investigated. The casting yield, tensile strength, hardness and absorbed energy during impact test were increased with increasing revolution speed. The effect of mass variation caused by the change in the revolution speed on the grain size was the most significant.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.123-124
• /
• 2006

This study aimed at exploiting low heat input characteristic of laser welding to effectively control grain coarsening in the fusion zone(FZ) and heat affected zone(HAZ) of 1.5mm thick 18wt% Cr ferritic stainless steel weld. The study demonstrated that as compared with gas tungsten arc welding(GTAW), laser welding brought about significant grain refinement in the FZ and HAZ. However, the impact absorbed energy of GTA weld was superior than that of laser weld because the strengthening effect during welding and cooling stage was higher In laser weld than that in GTA weld. The coarser grains in each weld than base metal resulted in an inferior toughness.

• Journal of the Korean Society for Railway
• /
• v.9 no.6 s.37
• /
• pp.695-700
• /
• 2006

This study investigates the effects of the material properties and the fatigue behavior in the SM490A material specimens due to the low-temperature atmosphere. In the fatigue behavior, the low-temperature affects the fatigue life. As the temperature get low, the fatigue limit increase, also As the yield strength and the tensile strength increase, the impact absorbed energy decrease. The difference of fatigue lift represents to normal distribution and it is larger between the room temperature and the low temperature, but in the result of the cumulative density function, the effect of temperature is not too large on it.