• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.507-512
• /
• 2000

The ob.jective of this study is to determine fracture behaviors(penetrati0n modes) and resistance to penetration duringballistic impact of Al 5052-H34 alloy laminates and anodized Al 5052-H34 alloy laminates. Resistance to penetration is determined by $V_{50}$ ballistic limit, a statical velocity with 50% probability for complete penetration, test method. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed that result from V50 test and Projectile Through Plates (PTP) test at velocities greater than $V_{50}$. PTP tests were conducted with 0" obliquity at room temperature using 5.56mm ball projectile. $V_{50}$ tests with 0" obliquity at room temperature were conducted with projectiles that were able to achieve near or complete penetration during PTP tests. Surface Hardness, resistance to penetration, and penetration modes of A1 5052-H34 alloy laminates compared to those of anodized Al 5052-H34 alloy laminates.y laminates.

• 비파괴검사학회지
• /
• 제13권4호
• /
• pp.32-41
• /
• 1994

탄성파에 의한 미소 동적 변위를 측정하기 위하여 안정화 회로가 부착된 Michelson 간섭계를 개발하였다. 안정화 회로는 외부 진동신호에 따른 광로차의 교란을 보상하기 위하여 압전구동기가 부착된 기준거울을 사용하였다. 안정화 회로를 사용함으로써, 간섭계는 외부 진동신호의 영향을 줄일 수 있었고, 항상 직각조건(quadrature condition)을 만족하여 광검출기의 출력신호가 최대의 감도와 선형성을 유지할 수 있었다. 검출가능한 최소 변위는 10MHz 대역에서 0.3nm 이었다. 개발된 간섭계를 사용하여 유리관 파괴 및 강철구 충격에 의한 진앙점에서의 변위를 검출하여 이론적으로 계산된 값과 비교하였다.

• 한국수소및신에너지학회논문집
• /
• 제22권4호
• /
• pp.504-511
• /
• 2011

Nano-sized Sn powder was prepared by pulsed wire evaporation method. The Sn powder and carbon black were charged in jar and ball milled. The milling time was varied with 10 min., 1h, 2h, and 4h, respectively. The milled powders were dried and the shape and size were observed by FE-SEM. Nano-sized Sn powders were plastic-deformed and agglomerated by impact force of balls and heat generated during the SPEX milling. The agglomerated Sn powder also consisted of many nano-sized particles. Initial discharge capacities of milled Sn electrode powders with carbon powder were milled for 10 min., 1h, 2h, and 4h were 787, 829, 827, and 816 mAh/g, respectively. After 5 cycle, discharge capacities of Sn electrode powders with carbon powder milled for 10 min., 1h, 2h, and 4h decreased as 271, 331, 351, and 287 mAh/g, respectively. Because Sn electrode powders milled for 2h constist of uniform and fine size, the cyclability of coin cell made of this powders is better than others.

• 한국정밀공학회지
• /
• 제20권12호
• /
• pp.126-134
• /
• 2003

In order to investigate the effect of surface treatment in Aluminium alloy and Titanium alloy which are used to armor material during ballistic impact, a ballistic testing was conducted. Anodizing was used to achieve higher surface hardness of Aluminium alloy and Iron plating in PVD(Physical Vapor Deposition) method was used to achieve higher surface hardness of Titanium alloy. Surface hardness test were conducted using a Micro victor's hardness tester. Ballistic resistance of these materials was measured by protection ballistic limit(V-50), a statical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed from the results of V-50 test and Projectile Through Plates (PTP) test at velocities greater than V-50. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature using 5.56mm ball projectile. V-50 tests were conducted with 0$^{\circ}$obliquity at room temperature with projectiles that were able to achieve near or complete penetration during PTP tests. Surface hardness, resistance to penetration. and penetration modes of surface treated alloy laminates are compared to those of surface non-treated alloy laminates. A high speed photography was used to analyze the dynamic perforation phenomena of the test materials.

• 한국운동역학회지
• /
• 제26권1호
• /
• pp.83-92
• /
• 2016

Objective: This study aimed to compare differences in biomechanical factors according to distance changes in relation to approaches during a round of golf to obtain basic data on golf swings. Methods: The research subjects were 8 KPGA-affiliated professional golfers who performed approach shots that put a ball into a circle of 8 feet in diameter from distances of 30, 50, and 70 m. Data were collected by using six infrared cameras and a ground reaction force device, which were applied to calculate biomechanical factors by using Kwon3D XP. The calculated data were subjected to one-way ANOVA by using SPSS 20.0, with the significance level set at p value of 0.05. Results: Elapsed time, stance width, clubhead position variation, clubhead synthesis speed, and cocking angle significantly differed according to distance change during the approach swing. Clubhead speed was positively related with stance width and clubhead displacement. Ground reaction force significantly differed according to distance change during the approach swing. Factors before and after showed differences in other states, except in the impact state. Conclusion: In the present study, we drew several conclusions regarding biomechanical factors and ground reaction forces according to distance change in the approach swing of professional golfers. According to these conclusions, we suggest that distance control with swing range is more important than power control in maintaining the accuracy and consistency of golf swing and is the most important mechanism of golf swing.

• 복식문화연구
• /
• 제27권6호
• /
• pp.666-680
• /
• 2019

Prevalent usage of mobile devices among consumers has been well recognized and this is especially imperative among young adult consumers. The mobile phone became the gateway of their communication, media consumption, retail transaction, education, and (virtual) social life. However, there is little empirical research explaining the dynamics behind the psychological underpinning of young adult consumers, specifically Generation Y, to understand their usages and dependency on mobile phones. This study, therefore, aims to unveil antecedents and consequences of Gen Y consumers' mobile phone dependency from a media psychological perspective. We developed a conceptual model based on theory of self-monitoring (Snyder 1974, 1987), extended self-concept (Belk, 1988), and media dependency theory (Ball-Rokeach & Defluer, 1976). Four hundred ninety-eight students in the U.S. provided usable responses to our pencil-and-paper survey. Causal modeling analysis results demonstrated that both ability to modify one's behavior and sensitivity to cues for social appropriate behavior dimensions of the self-monitoring tendency positively predicted one's level of fashion involvement, which in turn positively predicted his/her mobile phone dependency. Individual's mobile phone dependency, fashion involvement and self-monitoring's ability dimension exhibited positive and direct impact on one's perception of the salience of mobile phone case product attributes. Based on the findings, we provided pragmatic and theoretical implications for the industry and academia.

• 산업경영시스템학회지
• /
• 제38권2호
• /
• pp.101-107
• /
• 2015

Modern football has transformed into a scientific football based on data. With this trend, various methods for tactics studies and outcome prediction have been developed on the perspective of data analysis. In this paper, we propose a structural equation model for football game. We analyze critical factors that affect to the winning of game except psychological parts and the causal relationship between latent variables and observed variables is statistically verified through the proposed structural equation model. The results show that the Passing ability and the Ball possession affect to the Attack ability, and consequently it has a positive impact on the winning of game.

• 마이크로전자및패키징학회지
• /
• 제9권4호
• /
• pp.61-68
• /
• 2002

지금까지 전자 디바이스의 솔더접합부에 대한 신뢰성 평가에 있어서는 열충격시험에 의한 평가가 주류를 이루었다. 그러나 최근 모바일 제품이 소형화/다기능화되고 고밀도실장에 대한 요구가 증가함에 따라 BGA/CSP와 같은 솔더볼을 사용하는 패키지가 표면실장의 주류를 이루게 되었으며, 솔더접합부에 대한 메커니컬 스트레스 수명이 요구되어지고 있다. BGA/CSP의 솔더접합부에 대한 신뢰성 평가는 하중을 가한 상태에서 데이지체인 패턴의 전기적 저항변화와 스트레인 게이지에 의한 스트레스-스트레인 커브에 의해 행해진다. 본 연구에서는 자체 개발한 PCB만능시험장치의 응용과 솔더접합부에 대한 메커니컬 스트레스의 동적거동을 평가한 소니의 실험자료를 소개하도록 한다.

• Elastomers and Composites
• /
• 제54권2호
• /
• pp.135-141
• /
• 2019

Polyphenylene sulfide (PPS) was filled with glass fiber (GF), aramid fiber (AF), and solid lubricants to improve the mechanical properties and wear resistance. The addition of GF effectively enhanced the tensile strength, flexural modulus, and impact strength of PPS, while solid lubricants such as polytetrafluoroethylene (PTFE), molybdenum disulfide ($MoS_2$), and tungsten disulfide ($WS_2$) lowered the friction coefficients of the composites to below 0.3. The ball nut and motor pulley of the electric power steering (EPS) were manufactured using the PPS composites, and feasibility was ascertained thereafter by conducting the durability test. The composites filled with GF and AF showed high mechanical strength, but slip occurred at the interface between the pulley and belt while testing above $50^{\circ}C$. When small amounts of lubricants were added, the slip was no longer detected because of the suppression of friction heat. It is realized that the low friction as well as high mechanical properties is important to ensure the reliability of plastic pulleys.

• 한국분말재료학회지
• /
• 제30권4호
• /
• pp.332-338
• /
• 2023

Thermite welding is an exceptional process that does not require additional energy supplies, resulting in welded joints that exhibit mechanical properties and conductivity equivalent to those of the parent materials. The global adoption of thermite welding is growing across various industries. However, in Korea, limited research is being conducted on the core technology of thermite welding. Currently, domestic production of thermite powder in Korea involves recycling copper oxide (CuO). Unfortunately, controlling the particle size of waste CuO poses challenges, leading to the unwanted formation of pores and cracks during thermite welding. In this study, we investigate the influence of powder particle size on thermite welding in the production of Cu-thermite powder using waste CuO. We conduct the ball milling process for 0.5-24 h using recycled CuO. The evolution of the powder shape and size is analyzed using particle size analysis and scanning electron microscopy (SEM). Furthermore, we examine the thermal reaction characteristics through differential scanning calorimetry. Additionally, the microstructures of the welded samples are observed using optical microscopy and SEM to evaluate the impact of powder particle size on weldability. Lastly, hardness measurements are performed to assess the strengths of the welded materials.