• Current Optics and Photonics
• /
• v.5 no.5
• /
• pp.524-531
• /
• 2021

In an integral-imaging microscopy (IIM) system, a microlens array (MLA) is the primary optical element; however, surface errors impede the resolution of a raw image's details. Calibration is a major concern with regard to incorrect projection of the light rays. A ray-tracing-based calibration method for an IIM camera is proposed, to address four errors: MLA decentering, rotational, translational, and subimage-scaling errors. All of these parameters are evaluated using the reference image obtained from the ray-traced white image. The areas and center points of the microlens are estimated using an "8-connected" and a "center-of-gravity" method respectively. The proposed approach significantly improves the rectified-image quality and nonlinear image brightness for an IIM system. Numerical and optical experiments on multiple real objects demonstrate the robustness and effectiveness of our proposed method, which achieves on average a 35% improvement in brightness for an IIM raw image.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.126-126
• /
• 2009

X-ray high-voltage generator is the most important part that can decide the radiation exposure dose affecting a patient or operator according to the characteristic. If decrease of X-ray radiation exposure dose and output characteristic of high-voltage generator is unstable, a patient or operator must be exposed to more radiation. This study measures and analyzes the exposure dose reproducibility and output characteristic according to a change of tube current on the various rectification methods of diagnostic X-ray equipment. It can find that quality bastardize and output is increased if voltage of X-ray tube is increased. Exposure dose reproducibility according to output of X-ray equipment is extremely excellent in inverter type, and is stable in order of following three-phase, a single-phase and condenser method. This study can find that the reply incidence of high-voltage generator is generated due to difference in rectification method, noise occurs in X-ray due to that, quality of an image is decreased due to that, and medical diagnosis can be failed due to that.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.1
• /
• pp.63-68
• /
• 2006

Time series of waterline changes during a flood/ebb cycle can be utilized for supplementary data for measuring bottom topography. The waterlines extracted from consecutive images are substituted for depth contours using water level data. The distances between contours are quantified through a rectification image process. This technique is applied to the Keunpoolan beach in the Daeijak Island near Incheon. A camera monitoring technique supported by natural water level changes produces bottom topography with high precision. It is also less time consuming and more economical. The technique also can be utilized effectively to the physical modeling f3r measuring bottom changes in the three dimensional basin.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.659-663
• /
• 2009

In this paper, we propose a rectification method that can convert ray space data obtained by controlled camera array to ideal data. Here, Ideal data is obtained by getting longitudinal and transversal epipolar line between cameras vertical and horizontal. However it is actually difficult to arrange cameras strictly because we arrange cameras by hand. As conventional method, we have use camera-calibration method. But if we use this method there are some errors on the output image. When we generate arbitrary viewpoint images this error is critical problem. We focus attention on ideal trajectory of characteristic point. And to minimize the error directly we parallelize the real one. And we showed usefulness of proposed technique. Then using the proposed technique, we were successful reducing the error to less than 0.5 pixels.

• Journal of Korean Society for Geospatial Information Science
• /
• v.1 no.2 s.2
• /
• pp.83-96
• /
• 1993

The orthophto map is seen as the form of picture with the uniform reduced scale as the current terrain map. Thus it provides a reasonable feeling of scene and is easy to be interpreted. Furthermore, digital orthophoto is currently used as the basic terrain information data of the Geo-Spatial Information System(GSIS). Therefore, the orhtophoto map has high potential use as a future terrain map. This paper studies the method of producing orthophoto map by using the digital satellite imagery data taken from SPOT satellite of France. The production of orthophoto map requires the process of generating orthophoto imagery with digital elevation model, which process is called digital differential rectification. As the final accuracy of orthophoto map depends on that of digital elevation model, the precise and efficient production method of digital elevation model should be preceded. This study investigated the method of producing digital elevation model directly from SPOT satellite imagery and generated ortho-image by resampling the original SPOT imagery through digital differential rectification. Finally, Simple orthophoto map was made by overlaying the ortho-image and the contour map from digital elevation model.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.1
• /
• pp.60-68
• /
• 2017

In this study, we analyzed the real time video image obtained from the video monitoring system to grasp the shoreline, beach width, and area change of Haeundae beach. The video monitoring techniques enabled continuous monitoring for a long period at a much lower cost than general survey methods. It was possible to grasp quantitative beach variation characteristics of Haeundae beach through image acquisition, rectification, and image processing of video images. According to the monitoring results, the erosion rate of Haeundae beach in spring and summer was -19.8% in 2014 and -6.7% in 2015. The erosion rate in 2016 was -6.4%, which showed that the erosion rate in spring and summer continued to decrease. In particular, the influence of the erosion at the time of typhoon CHABA was revealed to be smaller than in the past. It can be concluded that these variations were due to beach width expansion by beach nourishment and the installation of submerged breakwaters.

• Korean Journal of Remote Sensing
• /
• v.22 no.2
• /
• pp.131-139
• /
• 2006

IKONOS images have the perspective geometry in CCD sensor line like aerial images with central perspective geometry. So the occlusion by buildings, terrain or other objects exist in the image. It is difficult to detect the occlusion with RPCs(rational polynomial coefficients) for ortho-rectification of image. Therefore, in this study, we detected the occlusion areas in IKONOS images using the nominal collection elevation/azimuth angle and restored the hidden areas using another stereo images, from which the rue ortho image could be produced. The algorithm's validity was evaluated using the geometric accuracy of the generated ortho image.

• Korean Journal of Remote Sensing
• /
• v.24 no.5
• /
• pp.463-471
• /
• 2008

The quality of orthoimages mainly depends on the elevation information and exterior orientation (EO) parameters. Since LiDAR data directly provides the elevation information over the earth's surface including buildings and trees, the concept of true orthorectification has been rapidly developed and implemented. If a LiDAR-driven digital surface model (DSM) is used for orthorectification, the displacements caused by trees and buildings are effectively removed when compared with the conventional orthoimages processed with a digital elevation model (DEM). This study utilized LiDAR data to generate orthorectified digital aerial images. Experimental orthoimages were produced using digital terrain model (DTM) and DSM. For the preparation of orthorectification, EO components, one of the inputs for orthorectification, were adjusted with the ground control points (GCPs) collected from the LiDAR point data, and the ground points were extracted by a filtering method used in a previous research. The orthoimage generated by DSM corresponded more closely to non-ground LiDAR points than the orthoimage produced by DTM.

• Journal of Broadcast Engineering
• /
• v.19 no.5
• /
• pp.590-605
• /
• 2014

The purpose of this paper is to propose a service system for a digital hologram video, which has not been published yet. This system assumes the existing service framework for 2-dimensional or 3-dimensional image/video, which includes data acquisition, processing, transmission, reception, and reconstruction. This system includes acquisition of color and depth image pairs from a image acquisition system with vertical rigs, rectification of acquired image pairs and generating digital hologram. Also it is designed to reduce the CGH (computer-generated hologram) generation time to 1/3. It also includes some additional and optional functions such as watermarking, compression, and encryption.

• Proceedings of the KSRS Conference
• /
• v.1
• /
• pp.409-412
• /
• 2006

Today's commercial high resolution satellite imagery such as IKONOS and QuickBird, offers the potential to extract useful spatial information for geographical database construction and GIS applications. Recognizing this potential use of high resolution satellite imagery, KARI is performing a project for developing Korea multipurpose satellite 3(KOMPSAT-3). Therefore, it is necessary to develop techniques for various GIS applications of KOMPSAT-3, using similar high resolution satellite imagery. As fundamental studies for this purpose, we focused on the extraction of 3D spatial information and the update of existing GIS data from QuickBird imagery. This paper examines the scheme for rectification of high resolution image, and suggests the convenient semi-automatic algorithm for extraction of 3D building information from a single image. The algorithm is based on triangular vector structure that consists of a building bottom point, its corresponding roof point and a shadow end point. The proposed method could increase the number of measurable building, and enhance the digitizing accuracy and the computation efficiency.