• 한국광학회지
• /
• 제18권1호
• /
• pp.31-36
• /
• 2007

직경과 초점거리가 수 mm인 카메라폰 렌즈의 성능을 평가하는 변조전달함수(Modulation Transfer Function: MTF) 측정장치를 개발 하였다. 전체 측정장치는 물체부, 상분석부, 렌즈 마운터로 구성되며, 물체부는 비축상 측정을 위하여 회전한다. 렌즈의 정밀한 정렬을 위하여 정밀한 수평형 거치대를 제작하였으며 광축 조정과 렌즈의 기울어짐 등의 문제를 매우 효과적으로 개선하였다. 시험렌즈의 초기정렬이 끝나면 자동으로 MTF를 측정하며 측정시간은 10초 이내이다.

• Corrosion Science and Technology
• /
• 제12권4호
• /
• pp.185-190
• /
• 2013

In the present study, $Ni-TiO_2$ composite coatings were electrodeposited in a sulfamate bath containing $TiO_2$ particles. The influence of the ultrasonic treatment on the co-deposition of $TiO_2$ particles in the coating and the hardness of the electrodeposited $Ni-TiO_2$ composite has been investigated. Three different ultrasonic treatments (pretreatment before the electrodeposition (pre-UT), pretreatment + applied during the electrodeposition (UT), and the electrodeposition without the ultrasonic treatment (w/o UT)) were performed. The $Ni-TiO_2$ composite coatings are characterized using scanning electron microscopy (SEM), image analyzer, and hardness tester. Comparison of results indicates that the volume fraction is more important factor than the agglomerated particle size in terms of the strength improvement, and the strength of the electrodeposited $Ni-TiO_2$ composite coatings is enhanced with pre-UT condition.

• Journal of Acupuncture Research
• /
• 제23권5호
• /
• pp.199-206
• /
• 2006

Objectives : The aim of this study was to investigate the effect of various electroacupuncture stimulation on neuronal nitric oxide synthase(nNOS) in cerebral cortex, brain stem, cerebellum of spontaneously hypertensive rats. Methods : We evaluated the changes of nNOS-positive neurons using a immunohistochemical method. The staining intensity of nNOS positive neurons was assessed in a quantitative fashion using a microdensitometrical method based on optical density by means of an image analyzer. Results : The average optical density of nNOS-positive neurons of 100 Hz (bipolar square wave 0.2 ms duration and 100 Hz frequency) electroacupuncture treatment group significantly decreased in most cortical areas comparison between the manual acupuncture and 2 Hz (bipolar square wave 0.2 ms duration and 2 Hz frequency) electroacupuncture groups. In the brain stem, the optical density of nNOS-positive neuron at superficial gray layer of the superior colliculus area, dorsolateral periaqueductal gray area and paralemniscal nucleus were same as cerebral cortex. Conclusion : We conclude that the morphological evidence for nNOS-positive neurons may be have regional change in cerebral cortex brain stem and cerebellum according to various electroacupuncture stimulations.

• 한국세라믹학회지
• /
• 제43권10호
• /
• pp.607-612
• /
• 2006

In VARTM (Vacuum Assisted Resin Transfer Molding) process, the permeability generally controls the filling time of the resin and it also affects the void characteristics of the fiber composite. In this study, carbon and glass fiber inter-layered hybrid composites (carbon fiber centered stack) with an epoxy matrix were fabricated by VARTM process and evaluated the resin flow and macro void characteristics. The permeability of glass fiber was higher than that of carbon fiber used in this study. Using Darcy's equation, the permeability of hybrid composites could be predicted and experimentally confirmed. After curing, the macro void content of hybrid composites was investigated using image analyzer. The calculated filling time was well agreed with experimental result and the void content was significantly changed in hybrid composites.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.707-711
• /
• 2016

A small diameter of SiC fiber mat can produce much higher heat under microwave irradiation than the other types of SiC materials. Fabrication of high strength SiC fiber consists of iodine vapor curing on polycarbosilane precursor and heat treatment process. The curing stage of polycarbosilane fiber was maintained at $150-200^{\circ}C$ in a vacuum condition under the iodine vapor to fabricate a high thermal radiation SiC fiber. The structure and morphology of the fibers were characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TG) and scanning electron microscopy (SEM). In this study, the thermal properties of SiC fiber mats under microwave have been analyzed with an IR thermal camera and its image analyzer. The prepared SiC fiber mats radiated high temperature with extremely high heating rate up to $1100^{\circ}C$ in 30 seconds. The fabricated SiC fiber mats were not oxidized after the heat radiation process under the microwave irradiation.

• Corrosion Science and Technology
• /
• 제19권1호
• /
• pp.1-7
• /
• 2020

Chalk River Unidentified Deposits (CRUDs) were collected from the Korean pressurized water reactor (PWR) plant (A, B, and C) where the axial offset anomaly (AOA) occurred. AOA, also known as a CRUD-induced power shift, is one of the key issues in maintaining stable PWR plant operations. CRUDs were sampled from spent nuclear fuel rods and analyzed using an electron probe micro-analyzer (EPMA). This paper describes the characteristics of boron-deposits from the CRUDs sampled from twice-burnt assemblies from the Korean PWR. The primary coolant of a PWR contains boron and lithium. It is known that boron deposition occurs in a thick CRUD layer under substantial sub-cooled nucleate boiling (SNB). The results of this study are summarized as follows. Boron was not found at the locations where the existence was confirmed in simulated CRUDs, in other words, the cladding and CRUD boundaries. Nevertheless, we clearly observed the presence of boron and confirmed that boron existed as a lump in crystalline form. In addition, the study confirmed that CRUD existed in a crystal form with a unique size of about 10 ㎛.

• 대한기계학회논문집B
• /
• 제32권8호
• /
• pp.574-581
• /
• 2008

The characteristics of combustion and flow for a lean premixed flame in lab-scale gas turbine combustor was studied through experiment and numerical analysis. From the experiment, flame structure and heat release rate were obtained from OH emission spectroscopy. Qualitative comparisons were made line-integrated OH chemiluminescence image and abel-transformed one. NOx analyzer was implemented to get the characteristic of NOx exhaust from the combustor. From the numerical analysis, the thermal distribution and characteristic of recirculation zone with the change of fuel-air mixing degree, the characteristic of methane distribution with equivalence ratio in the combustor respectively. Total heat release rate is increased with increasing equivalence ratio. Thermal Nox is reduced with increasing fuel-air mixing degree. Increasing equivalence ratio results in the decrease of the size of reaction zone and alteration of the position of the reaction zone into the entrance of the combustor.

• Elastomers and Composites
• /
• 제55권2호
• /
• pp.108-113
• /
• 2020

Wear particles of the model tread compounds for bus and truck tires were made using a laboratory abrasion tester and characterized based on their size distributions, shapes, and crosslink densities. The influence of the carbon black contents and rubber compositions (NR= 100 and NR/BR= 80/20) on the production of wear particles was investigated. The wear particles were separated according to size using a sieve shaker. The shape properties of the wear particles were analyzed using an image analyzer and scanning electron microscopy (SEM). Their shapes were observed as tiny stick cookies or sausages with bumpy surfaces. The particle size distribution tended to be smaller with increasing carbon black content. Moreover, the particle size distributions of the NR = 100 samples were larger than that of the NR/BR blend samples. There were different filaments in the wear particles. The filament diameters tended to be thinner with increasing carbon black content. The crosslink density increased with increasing carbon black content, and the crosslink densities of the NR= 100 samples were lower than those of the NR/BR blend ones. The particle size distribution tended to be smaller with increasing crosslink density. Based on the experimental results, the wear particles can be produced by detaching debris from the main body through repetitive strain and recovery.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2002년도 추계학술발표논문집 (상)
• /
• pp.813-816
• /
• 2002

컴퓨터 보급의 급속한 발전과 멀티미디어의 등장으로 기존의 텍스트와 이미지, 음성, 오디오, 동영상 등의 정보를 디지털화하고, 컴퓨터를 이용하여 저장, 처리, 전송하게 되면서 의료 분야에서도 상당한 업무의 변화를 요구하게 되었다. 의료 분야에서의 이러한 급격한 개방과 더불어 초고속 정보 통신의 발달은 원격진료라는 또 다른 요구를 대두시키고 있다. 이를 위해서는, 멀티미디어 기술, 대용량의 정보를 저장하는 데이터베이스 기술, 초속의 광 대역 기술 등을 통합하여 종합적인 멀티미디어 의료 정보 시스템을 구축하는 것이 시급하다. 이러한 이유들로 본 논문에서는 병원/의원의 의료진들로 하여금 의료영상이나 자료를 상호 전송하여 환자의 진료 또는 검진결과를 확인하고 전문가의 조언 등을 구하는 원격 진료용 의료영상 시스템의 요구사항을 분석, 설계하고 구현하였다. 본 시스템은 클라이언트/서버 구조로써 영상 획득 및 출력, 의료영상 국제 표준 포맷인 DICOM 포맷으로의 영상 저장, MCA(Multi Channel Analyzer), ROI(Region Of Interest) 등의 영상 분석, 필터링 및 영상 확대/축소/회전 등의 각종 영상 처리의 주요 기능을 갖으며, 사용자가 편리하고 쉽게 사용할 수 있도록 아이콘(icon) 중심의 직관적인 인터페이스를 갖는다.

• 한국주조공학회지
• /
• 제29권3호
• /
• pp.144-149
• /
• 2009

In this study, we investigated optimum condition of cooling plate method to obtain semi-solid AM100A Mg alloy with fine and globular morphology. AM100A Mg alloy were hot extruded at $380^{\circ}C$ extrusion temperature under extrusion ratio of 25 : 1 and ram speed of 2.4 mm/sec. Vickers hardness test, optical microscopy, scanning electron microscopy, and image analyzer were performed to identify the optimum conditions of cooling plate method. Optimum conditions of cooling plate method to fabricate semi-solid AM100A Mg alloy with fine and globular microstructures were achieved at a pouring temperature of $602^{\circ}C$ and the angle of cooling plate of 60 degree.