• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.17-24
• /
• 2004

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthened. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, it is well known that HCCI engines increased HC and CO. Thus, the investigation of combustion characteristics which consists cool and hot flames for HCCI engines were needed to obtain the optimal combustion condition. In this study, combustion characteristics for direct injection type HCCI engine such as quantity of cool flame and hot flame, ignition timing and ignition delay were investigated to clarify the effects of these parameters on performance. The results revealed that diesel combustion showed the two-stage ignition of cool flame and hot flame, the rate of cool flame increase and hot flame decrease with increasing intake air temperature. On the other hand, the gasoline combustion is the single-stage ignition and ignition timing is near the TDC. In addition mixed fuel combustion showed different phenomenon, which depends on the ratio of gasoline component. Ignition timing of mixed fuel is retarded near the TDC and the ignition delay is increased according to ratio of gasoline.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.311-316
• /
• 2010

The ignition and the burning characteristics of aluminum and magnesium particles ($30-110{\mu}m$ in diameter) isolated due to electrodynamic levitation were experimentally investigated. The burning time, the ignition delay time, the flame temperature, and the flame diameter were measured. The thermal radiation intensity was measured using the photomultiplier tube and the combustion history was monitored by high-speed cinematography. Two-wavelength pyrometry measured the temperature of the burning particles. The burning times of aluminum particles were measured approximately 5 to 8 times longer than those of magnesium particles. Exponents of $D^n$-law, for the burning rate of magnesium and aluminum particles of diameters less than $110{\mu}m$, are found to be 0.6 and 1.5, respectively. The instant of aluminum ignition is clearly distinguished with the ignition delay time little less than 10 ms, however the burning history of magnesium particle exhibits no distinct instant of the ignition. The ignition delay time of magnesium particle (less than $110{\mu}m$) were approximately shown in the range from 50 to 200 ns. The flame temperatures of single metal particles are lower than the boiling point of the oxide. The nondimensional flame diameters for magnesium are decreased with increasing of the diameter. The nondimensional flame diameters for aluminum are not changed significantly.

• Korean Chemical Engineering Research
• /
• 제57권5호
• /
• pp.620-627
• /
• 2019

본 연구에서는 서로 다른 원료를 이용하여 HEFA 공정을 통해 제조한 국내외 바이오항공유(Bio-ADD, Bio-6308, Bio-7720)의 점화지연특성을 비교 및 분석하였으며, 이러한 바이오항공유의 실제 시스템에의 적용 가능성을 확인하기 위하여 기존에 사용되고 있는 석유계항공유(Jet A-1) 및 바이오항공유와 석유계항공유를 일정한 비율(50:50, v:v)로 혼합한 연료의 점화지연특성에 대해서도 분석하였다. 각 항공유의 점화지연시간은 CRU 장비를 사용하여 측정하였으며, 결과 해석을 위해 표면장력 측정, GC/MS 및 GC/FID 분석을 수행하였다. 그 결과, 모든 온도 조건에서 Jet A-1의 점화지연시간이 가장 길게 측정되었는데, 이는 aromatic compounds가 약 22.8% 존재하여 분해 과정에서 열적으로 안정하고 주변 산소와도 반응성이 낮은 benzyl radical이 생성되기 때문인 것으로 판단된다. 바이오항공유의 점화지연시간은 모두 비슷하게 측정되었는데, 이는 각 항공유를 구성하는 n-paraffin과 iso-paraffin의 비율(n-/iso-)이 약 0.12로 서로 비슷한 값을 가지며, cycloparaffin의 구성 비율도 약 3% 미만으로 크게 차이가 없기 때문인 것으로 해석된다. 또한, 국내외에서 개발된 바이오항공유(Bio-ADD, Bio-6308)를 석유계항공유와 50:50(v:v)으로 혼합한 연료의 점화지연시간은 혼합하지 않은 Jet A-1과 각 바이오항공유가 갖는 점화지연시간의 사잇값으로 측정되어, 기존에 사용 중인 시스템을 변경하거나 개선하지 않아도 적용이 가능함을 확인하였다.

• 한국연소학회지
• /
• 제22권1호
• /
• pp.8-13
• /
• 2017

Ignition delay time of methane/oxygen mixture is measured experimentally with the shock tube in order to obtain the data for high pressure conditions where gas turbines and internal combustion engines are operating. The shock tube experiment is validated first over the temperature range of 1400-2000 K at 10 bar and with the various equivalence ratios of 0.5, 1 and 2. The measured ignition delays are compared with the data from the literatures. And then, experiments are conducted for non-explored conditions, i.e., at 40 bar and with the equivalence ratio of 1.5. The present experimental data show a good agreement with the available ones from the literatures and reasonable dependence on pressure and equivalence ratio. In addition, the effects of the temperature and equivalence ratio on ignition delay time are analyzed.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.213-215
• /
• 2012

As one of the primary fuel sources, oxy-fuel combustion of coal is actively being investigated because of the climate changing problem such like the emission of green house gases. In this paper research about the pulverized coal technology, which is widely used in both power-generating and iron-making processes was studied to invesgate the ignition behaviour of pulverized coal particles during coal combustion as changing the ambient oxygen concentration of the particle. The ignition phenomenon of the coal particles fed into a laminar flow reactor was imaged with a Integrated charged-coupled device (ICCD) camera. The ignition points were determined throught the analysis of the images, and then the ignition delay times were able to be calculated. The experiment results show that a lower oxygen concentration increases the ignition delay time.

• 한국안전학회지
• /
• 제19권2호
• /
• pp.54-60
• /
• 2004

Flammable substances are frequently used chemical industry processes. An accurate knowledge of the ALTs(Autoignition Temperatures) is important in developing appropriate prevention and control measures in industrial fire protection. The AITs describe the minimum temperature to which a substance must be heated, without the application of a flame or spark, which will cause that substance to ignite. The AITs are dependent upon many factors, namely initial temperature, pressure, volume, fuel/air stoichiometry, catalyst material, concentration of vapor, ignition delay. This study measured relationship between the AITs and the ignition delay times by using ASTM E659-78 apparatus for methanol and ethanol. The A.A.P.E.(Average Absolute Percent Error) and the A.A.D.(Average Absolute Deviation) of the experimental and the calculated delay times by the AITs for methanol were 14.59 and 1.76 respectively. Also the A.A.P.E. and the A.A.D. of the experimental and the calculated delay times by the ATIs for ethanol were 8.33 and 0.88.

• 한국연소학회지
• /
• 제18권2호
• /
• pp.32-41
• /
• 2013

This study presents both experimental and numerical investigation of ignition delay time of n-heptane and n-butanol binary fuel. The $O_2$ concentration in the mixture was set to 9-10% to make high exhaust gas recirculation( EGR) rate condition which leads low NOx and soot emission. Experiments were performed using a rapid compression machine(RCM) at compressed pressure 20bar, several compressed temperature and three equivalence ratios(0.4, 1.0, 1.5). In addition, a numerical study on the ignition delay time was performed using CHEMKIN codes to validate experimental results and predict chemical species in the combustion process. The results showed that the ignition delay time increased with increasing the n-butanol fraction due to a decrease of oxidation of n-heptane at the low temperature. Moreover, all of the binary fuel mixtures showed the combustion characteristics of n-heptane such as cool flame mode at low temperature and negative-temperature-coefficient(NTC) behavior. Due to the effect of high EGR rate condition, the operating region is reduced at lean condition and the ignition delay time sharply increased compared with no EGR condition.

• 대한화학회지
• /
• 제48권1호
• /
• pp.12-16
• /
• 2004

에탄올-산소-아르곤 혼합기체의 점화 과정을 반사 충격파를 이용 1281-1625 K의 온도 범위 및 0.69-1.06 bar 압력 범위에서 고찰하였다. 점화지연시간은 급격한 압력변화와 광 방출 스펙트럼으로부터 측정하였으며, 에탄올 및 산소 기체의 농도 그리고 반응온도에 따른 점화지연시간의 의존관계를 나타내는 실험식을 구할 수 있었다. 실험결과 에탄올 점화 과정에서 연료인 에탄올의 농도가 커지면 점화지연시간이 길어지는 경향을 보였으며, 이는 메탄올 점화 과정에서 메탄올의 농도가 증가하면 점화 과정이 짧아지는 것과는 다른 경향이었다. 그리고 에탄올 점화 과정에 관하여 보다 자세히 고찰하기 위해 다양한 에탄올 연소반응 메카니즘을 이용하여 모델 연구를 수행하였다.

• 한국연소학회지
• /
• 제4권1호
• /
• pp.59-65
• /
• 1999

Ignition of $NH_3-O_2-Ar$ mixtures have been studied behind reflected shock waves over the temperature range of 1600-2300 K and the pressures in the range of 1.1-1.6 atm. The pressure profile and the radiation emitted behind the shock waves have been monitored to give empirical correlations between ignition delay times and the mixture concentrations with the experimental conditions. On the basis of this data, several kinetic mechanisms proposed for ammonia oxidation at high temperatures have been tested. The ignition delay times obtained from the mechanism proposed by Miller and Smook were in good agreement with our experimental results.

• 한국추진공학회지
• /
• 제10권3호
• /
• pp.67-72
• /
• 2006

HTPB/AP 혼합형 추진제(A형)와 니트라민계 산화제가 소량 함유된 추진제의 진공 점화 특성을 고찰하였다. 추진제의 임계 점화 압력은 4 psia로 판단되었고, AP의 일부를 HMX와 HNIW로 $5{\sim}l5%$ 치환한 니트라민계 혼합형 추진제(B형)에서 임계 압력은 0.4 psia, 점화지연시간은 50% 이상 향상되었다. 이는 HMX나 HNIW가 AP에 비해 낮은 온도(${\sim}220^{\circ}C$)에서 발열 분해되는 특성에 기인되는 것으로 보인다. 점화도움물질인 $B/KNO_3$를 추진제 표면에 코팅한 결과,15% 정도 점화성이 개선되었다. $B/KNO_3$에 2차 결합제로 NC를 소량 사용하고, 이를 추진제 그레인의 점화도움물질로 적응하였다.