• Proceedings of the Optical Society of Korea Conference
• /
• 2005.07a
• /
• pp.28-29
• /
• 2005

본 논문에서는 MEH-PPV와 DFPP의 폴리머 물질을 이용하여 photovoltaic device가 제작되었고, 그림 1에 두 물질의 분자 구조가 보여진다. Photovoltaic cell의 전기-광학적 특성은 활성층의 폴리머 물질에 의해 결정된다. 이러한 특성을 알아보기 위해서 홉수 스펙트럼이 측정되었다. DFPP는 chloroform, chlorobenzen, THF, acetone에 잘 녹았으며, 본 논문에서는 chloroform이 용매로 사용되었다. 제작 공정은 다음과 같다. 인듐 주석 산화물 (ITO)이 증착된 유리기판은 photolithography 공정을 거친 후, 왕수(HNO$_{3}$ + HCL)로 식각됨으로서 전극의 패턴이 제작되었다. 그리고 ITO 전극 패턴 된 유리기판 위에 PEDOT (CH8000, Baytron)이 코팅된 후 Ar이 주입되는 Convection Oven을 이용하여 120$^{\circ}$C에서 2시간 동안 열처리되어 수분이 제거되었다. 활성층에는 MEH-PPV와 DFPP가 9:1과 2.33:1로 혼합된 폴리머가 사용되었고, 이것은 0.3 %w.t.가 되도록 chloroform에 넣어 5시간 동안 스핀바를 돌려서 용해되었다. 이 용액은 ITO 전극 패턴이 형성된 글라스 위에 3000 rpm으로 45 초간 스핀코팅 되었다. 이 때 얻어진 유기물 박막층은 80$^{\circ}$C의 Ar이 주입되는 convection oven에서 3시간 동안 경화되었다. 경화된 단층 유기물 박막층 위에 Li-Al이 1000 ${\AA}$의 두께로 증착되어 전극이 형성되었고, 이후 질소가 채워진 globe box에서 소자는 encapsulation되어 산소와 수분에 대한 영향으로부터 차단되었다. 상기의 공정으로 제작된 소자의 박막구조는 그림 2에서 보여진다. 그림 3은 MEH-PPV와 DFPP를 혼합했을 때의 흡수 스펙트럼이다. 최대 흡수 파장은 511 nm였다. 그리고 photovoltaic cell의 V-I 특성 결과가 그림 4와 같이 측정되었다. 측정에서는 300${\sim}$700 nm의 파장대를 갖는 태양광 모사계가 사용되었고, 셀의 면적은 10 mm$^{2}$였다. 그림 5의 I-V 특성으로부터 MEH-PPV와 DFPP가 9:1 로 혼합했을 때보다 2.33:1 로 혼합했을 때, photovoltaic device의 효율이 향상됨을 확인할 수 있다. 빛이 75 mW/cm$^{2}$ 의 세기로 조사될 때 9:1과 2.33:1로 혼합된 소자의 open circuit voltage (V$_{oc}$)는 비슷하지만, short circuit current Density (J$_{sc}$)는 각각 -1.39 ${\mu}$A/cm$^{2}$ 와 -3.72${\mu}$A/cm$^{2}$ 로 약 2.7배 정도 증가되었음을 볼 수 있다. 이러한 결과를 통해 electron acceptor인 DFPP의 비율이 높아질수록 photovoltaic cell의 conversion efficiency가 더 크게 됨을 확인할 수 있다. 그러므로 효율이 최대가 되는 두 폴리머의 혼합 비율이 최적화되는 조건을 찾는 것은 매우 중요한 연구가 될 것이다.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.4
• /
• pp.69-73
• /
• 2007

The MIM(metal-insulator-metal) capacitors with the Al/PMMA/ITO/Glass structures were manufactured according to various PMMA concentration of 1, 2, 4, 6, 8 wt%. The lowest leakage current and the largest capacitance were found to be 2.3 pA and 1.2 nF, respectively, for the device with 2 wt% PMMA concentration. The measured capacitance of the devices was almost same values with the calculated one. The optimum film thickness was obtained at the value of 48 nm, showing that the capacitance and leakage current were 1.92 nF, 0.3 pA at 2 wt%, respectively. From this experiment, the PMMA gate insulator films can be applicable to the organic thin film transistors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.9
• /
• pp.1323-1329
• /
• 2015

The WO₃/Ag/WO₃ transparent thin films are fabricated by the RF magnetron sputtering. This has a transmittance of front and rear about 90% in the visible light range and surface resistance of 6.41Ω/□. In this paper, we analyzed the surface characteristics caused by the working pressure and O₂ plasma surface treatment to apply a transparent electrode that was prepared to the laminated structure with other materials. The working pressure was changed in the WO₃ film to 10mTorr, 7mTorr, and 5mTorr, it showed a lower than roughness of conventional ITO. In addition, by 55.5774 J/m² at 5mTorr, it shows the hydrophobic property with lower process pressure. O₂ plasma surface treatment was changed at the condisions of the RF power to 150W, 100W, and 50W and the process time to 240s, 180s, 120s, and 60s. The surface roughness are the maximum roughness(Rmax) 6.437nm and the average roughness(Rq) 0.827nm at RF power 150W, and the maximum roughness (Rmax) 6.880nm and the average roughness (Rq) 0.839nm at process time 240sec. It showed a lower value than the surface treatment. also about working pressure and process time is increased, it showed the hydrophobic.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.4
• /
• pp.345-351
• /
• 2004

Highly ordered pure-silica MCM-41 materials possessing well-defined morphology have been successfully prepared with surfactant used as a template. The fabrication of mesoporous silica has received considerable attention due to the need to develop more efficient materials' for catalysis, separations, and chemical sensing. The surface modified MCM-41 was used as anadsorbent for biomolecules. Silica-supported organic groups and DNA adsorption on surface modified MCM-41 were investigated by FT-IR and UV-Vis spectrometer, respectively. The use of MCM-41 as the modification of electrode surfaces were investigated electrochemical properties of metal mediators with biomolecules. The modified ITO electrodes increased peak currents for a redox process of $[Ru(bpy)_3]^{2+}$ relative to the bare electrode. The electrochemical detection of DNA by cyclic voltammetry when the current is saturated in the presence of the mediator appeared more sensitive due to a higher catalytic current on the MCM-41 supported electrodes modified by carboxylic acid functional groups. The carboxyl or amine groups on the surface of MCM-41 interact and react with the $-NH_2$ groups of guanine and backbone, respectively. Highly ordered mesoporous materials with organic groups could find applications as DNA sensors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.539-544
• /
• 2013

To study the encapsulation method for heat dissipation of high brightness organic light emitting diode (OLED), red emitting OLED of ITO (150 nm) / 2-TNATA (50 nm) / NPB (30 nm) / $Alq_3$ : 1 vol.% Rubrene (30 nm) / $Alq_3$ (30 nm) / LiF (0.7 nm) / Al (200 nm) structure was fabricated, which on $Alq_3$ (150 nm) / LiF (150 nm) as buffer layer and Al as protective layer was deposited to protect the damage of OLED, and subsequently it was encapsulated using attaching film and metal sheet. The current density, luminance and power efficiency was improved according to thickness of Al protective layer. The emission spectrum and the Commission International de L'Eclairage (CIE) coordinate did not have any effects on encapsulation process using attaching film and metal sheet The lifetime of encapsulated OLED using attaching film and metal sheet was 307 hours in 1,200 nm Al thickness, which was increased according to thickness of Al protective layer, and was improved 7% compared with 287 hours, lifetime of encapsulated OLED using attaching film and flat glass. As a result, it showed the improved current density, luminance, power efficiency and the long lifetime, because the encapsulation method using attaching film and metal sheet could radiate the heat on OLED effectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.5
• /
• pp.437-443
• /
• 2000

In this study several lanthanide complexes such as Eu(TTA)$_3$(Phen), Tb(ACAC)$_3$-(Cl-Phen) were synthesized and the white-light electroluminescence(EL) characteristics of their thin films were investigated where the devices having structures of anode/TPD/Tb(ACAC)$_3$(Cl-Phen)/Eu(TTA)$_3$(Phen)/Alq$_3$or Bebq$_2$/cathode and the low work function metal alloy such as Li:Al was used as the electron injecting electrode(cathode). Device structure of glass substrate/ITO/TPD(30nm)/Tb(ACAC)$_3$(Phen)(30nm)/Eu(TTA)$_3$(Phen)(6nm)/DCM doped Alq$_3$(10nm)/Alq$_3$(20nm)/Li:Al(100nm) was also fabricated and their EL characteristics were investigated where Eu(TTA)$_3$(Phen) and DCM doped Alq$_3$were used as red light-emitting materials. It was found that the turn-on voltage of the device with non-doped Alq$_3$was lower than that of the devices with doped Alq$_3$and the blue and red light emission peaks due to TPD and Eu(TTA)$_3$(Phen) with non-doped Alq$_3$were lower than those with DCM doped Alq$_3$Details on the white-light-emitting characteristics of these device structures were explained by the energy and diagrams of various materials used in these structure where the energy levels of new materials such as ionization potential(IP) and electron affinity(EA) were measured by cyclic voltametric method.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.521-528
• /
• 2008

We present the structural, optical, and electrical properties of amorphous silicon suboxide (a-$SiO_x$) films grown on indium tin oxide glass substrates with a radio frequency magnetron technique from a polycrystalline silicon oxide target using ambient Ar. For different substrate-target distances (d = 8 cm and 10 cm), the deposition temperature effects were systematically studied. For d = 8cm, oxygen content in a-$SiO_x$ decreased with dissociation of oxygen onto the silicon oxide matrix; temperature increased due to enlargement of kinetic energy. For d = 10 cm, however, the oxygen content had a minimum between $150^{\circ}\;and\;200^{\circ}$. Using simple optical measurements, we can predict a preferred orientation of liquid crystal molecules on a-$SiO_x$ thin film. At higher oxygen content (x > 1.6), liquid crystal molecules on an inorganic liquid crystal alignment layer of a-$SiO_x$ showed homogeneous alignment; however, in the lower case (x < 1.6), liquid crystals showed homeotropic alignment.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.1
• /
• pp.9-13
• /
• 2002

Recently, Organic electroluminescent devices (OELDs) have been demonstrated the medium sized full color display with effective multi-layer thin films. In this study, the multi-layer OELDs were prepared on the patterened ITO (indium tin oxide)/glass substrates by the vacuum thermal evaporation method. The low molecule compounds such as $Alq_3$(trim-(8-hydroxyquinoline)aluminum) and CTM (carrier transfer material) as the electron transport and injection layers as well as TPD (triphenyl-diamine) and CuPc (copper phthalocyanine) as the hole transport and injection layers were used. The luminance was rapidly increased above the threshold voltage of 10 V. The luminance and emission spectrum for the OELDs samples with $A1/CTM/Alq_3$/TPD/1TO structures were found to be 430 cd/$m^2$and 512 nm at 17 V showing green color emission. In contrast, the samples with $Li-A1/Alq_3$/TPD/CuPC/1TO multi-structures showed 508 nm in emission spectrum and 650 cd/$m^2$at 17 V in the luminance. The increment of luminance may be ascribed to the improved efficiency of recombination in the region of the emission layers by the deposition of CuPc as hole injection layer and the low work function of the Li-Al electrode compared to the Al electrode.