• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 중소기업연구
• /
• 제31권4호
• /
• pp.67-93
• /
• 2009

본 연구는 1999년 1월 1일부터 2007년 12월 31일까지 한국거래소의 유가증권시장과 코스닥시장에 상장된 혁신형 중소기업을 대상으로 재무적 제약과 배당스무딩간의 관계를 실증분석 하였으며, 주요한 분석결과는 다음과 같다. 기업들은 목표 배당성향을 가지고 있으며, 실제 배당성향이 목표 배당성향에서 이탈하면 다시 배당지급을 부분적으로 조정한다. 배당조정속도는 Lintner(1956)의 배당조정모형의 핵심변수인 전기 주당배당과 당기 주당이익을 사용하여 거의 대부분 측정할 수 있으며, 잔여배당이론과 그 이후에 등장한 배당신호이론, 대리인이론, 케이터링 이론 및 거래비용이론에 관한 대용변수들은 배당조정속도에 부분적으로 영향을 미친다. 그리고 전기 주당배당은 당기 주당이익보다 배당조정속도에 더 큰 영향을 미치는데, 이는 기업들이 특별한 이유가 없는 한 전기 주당배당 수준을 장기적으로 유지하는 안정적인 배당정책을 선호한다는 증거가 된다. 혁신형 중소기업은 비혁신형 중소기업보다 배당조정속도가 더 빠르다. 혁신형 중소기업은 R&D 투자에 따른 미래의 성장성과 수익성을 담보로 하여 장기적으로 안정적인 배당정책을 유지할 수 있다. 다시 말해, 혁신형 중소기업은 배당지급이 목표 배당성향에서 이탈하더라도, R&D 투자에 따른 미래의 성장성과 수익성을 담보로 하여 목표 배당성향을 향하여 배당지급을 신속하게 조정하여 배당스무딩을 효과적으로 달성할 수 있다. 그리고 혁신형 중소기업 중에서도 재무적 비제약 기업은 재무적 제약 기업보다 배당조정속도가 더 빠르다. 이는 재무적 비제약 기업일수록 자본시장을 통한 외부 자금조달이 용이하기 때문에 주당배당을 신속하게 조정한다는 증거가 된다. 따라서 자본시장 접근성이 용이하여 재무적 제약을 적게 받는 기업일수록 외부 자금조달이 용이하기 때문에 배당지급을 더 신속하게 조정함으로써 배당스무딩을 더 효과적으로 달성할 수 있다. 그리고 중소기업청이 정책적 목적으로 분류한 혁신형 중소기업(벤처기업, 이노비즈기업, 경영혁신형기업)은 비혁신형 중소기업보다 배당조정속도가 더 빠르다. 중소기업청에서 정책적 목적으로 분류한 혁신형 중소기업은 신용보증지원, 정책자금지원, 조세혜택, 공공입찰 우선권 부여 등과 같은 다양한 정책적 혜택으로 인해 재무적 제약을 적게 받기 때문에 배당지급을 더 신속하게 조정할 수 있다. 결론적으로, 한국거래소의 유가증권시장과 코스닥시장에 상장된 혁신형 중소기업은 비혁신형 중소기업보다 배당조정속도가 더 빠르고, 혁신형 중소기업 중에서도 재무적 비제약 기업은 재무적 제약 기업보다 배당조정 속도가 더 빠르다. 다시 말해, 중소기업 중에서도 R&D 집중도가 높은 혁신형 중소기업은 R&D 투자에 따른 미래의 성장성과 수익성을 담보로 하여 배당스무딩을 신속하게 할 수 있고, 혁신형 중소기업 중에서도 자본시장 접근성이 좋은 기업은 재무적 제약을 적게 받기 때문에 배당스무딩을 더 신속하게 할 수 있다. 따라서 중소기업 경영자는 R&D 집중도를 증가시키고 자본시장 접근성을 높여 재무적 제약을 회피함으로써 신속한 배당스무딩을 통해 장기적으로 안정적인 배당정책을 유지할 수 있다고 생각한다. 그리고 중소기업청이 정책적 목적으로 분류한 혁신형 중소기업(벤처기업, 이노비즈기업, 경영혁신형기업)의 경우에도 배당조정속도가 비혁신형 중소기업보다 더 빠르게 나왔다. 이러한 결과는 배당정책의 측면에서 중소기업청의 혁신형 중소기업 정책을 지지하는 실증적인 증거가 된다.

• Journal of Preventive Medicine and Public Health
• /
• 제20권1호
• /
• pp.165-203
• /
• 1987

This project was a service-cum-research effort with a quasi-experimental study design to examine the health benefits of an integrated Family Planning (FP)/Maternal & Child health (MCH) Service approach that provides crucial factors missing in the present on-going programs. The specific objectives were: 1) To test the effectiveness of trained nurse/midwives (MW) assigned as change agents in the Health Sub-Center (HSC) to bring about the changes in the eight FP/MCH indicators, namely; (i)FP/MCH contacts between field workers and their clients (ii) the use of effective FP methods, (iii) the inter-birth interval and/or open interval, (iv) prenatal care by medically qualified personnel, (v) medically supervised deliveries, (vi) the rate of induced abortion, (vii) maternal and infant morbidity, and (viii) preinatal & infant mortality. 2) To measure the integrative linkage (contacts) between MW & HSC workers and between HSC and clients. 3) To examine the organizational or administrative factors influencing integrative linkage between health workers. Study design; The above objectives called for quasi-experimental design setting up a study and control area with and without a midwife. An active intervention program (FP/MCH minimum 'package' program) was conducted for a 2 year period from June 1982-July 1984 in Seosan County and 'before and after' surveys were conducted to measure the change. Service input; This study was undertaken by the Soonchunhyang University in collaboration with WHO. After a baseline survery in 1981, trained nurses/midwives were introduced into two health sub-centers in a rural setting (Seosan county) for a 2 year period from 1982 to 1984. A major service input was the establishment of midwifery services in the existing health delivery system with emphasis on nurse/midwife's role as the link between health workers (nurse aids) and village health workers, and the referral of risk patients to the private physician (OBGY specialist). An evaluation survey was made in August 1984 to assess the effectiveness of this alternative integrated approach in the study areas in comparison with the control area which had normal government services. Method of evaluation; a. In this study, the primary objective was first to examine to what extent the FP/MCH package program brought about changes in the pre-determined eight indicators (outcome and impact measures) and the following relationship was first analyzed; b. Nevertheless, this project did not automatically accept the assumption that if two or more activities were integrated, the results would automatically be better than a non-integrated or categorical program. There is a need to assess the 'integration process' itself within the package program. The process of integration was measured in terms of interactive linkages, or the quantity & quality of contacts between workers & clients and among workers. Intergrative linkages were hypothesized to be influenced by organizational factors at the HSC clinic level including HSC goals, sltrurture, authority, leadership style, resources, and personal characteristics of HSC staff. The extent or degree of integration, as measured by the intensity of integrative linkages, was in turn presumed to influence programme performance. Thus as indicated diagrammatically below, organizational factors constituted the independent variables, integration as the intervening variable and programme performance with respect to family planning and health services as the dependent variable: Concerning organizational factors, however, due to the limited number of HSCs (2 in the study area and 3 in the control area), they were studied by participatory observation of an anthropologist who was independent of the project. In this observation, we examined whether the assumed integration process actually occurred or not. If not, what were the constraints in producing an effective integration process. Summary of Findings; A) Program effects and impact 1. Effects on FP use: During this 2 year action period, FP acceptance increased from 58% in 1981 to 78% in 1984 in both the study and control areas. This increase in both areas was mainly due to the new family planning campaign driven by the Government for the same study period. Therefore, there was no increment of FP acceptance rate due to additional input of MW to the on-going FP program. But in the study area, quality aspects of FP were somewhat improved, having a better continuation rate of IUDs & pills and more use of effective Contraceptive methods in comparison with the control area. 2. Effects of use of MCH services: Between the study and control areas, however, there was a significant difference in maternal and child health care. For example, the coverage of prenatal care was increased from 53% for 1981 birth cohort to 75% for 1984 birth cohort in the study area. In the control area, the same increased from 41% (1981) to 65% (1984). It is noteworthy that almost two thirds of the recent birth cohort received prenatal care even in the control area, indicating that there is a growing demand of MCH care as the size of family norm becomes smaller 3. There has been a substantive increase in delivery care by medical professions in the study area, with an annual increase rate of 10% due to midwives input in the study areas. The project had about two times greater effect on postnatal care (68% vs. 33%) at delivery care(45.2% vs. 26.1%). 4. The study area had better reproductive efficiency (wanted pregancies with FP practice & healthy live births survived by one year old) than the control area, especially among women under 30 (14.1% vs. 9.6%). The proportion of women who preferred the 1st trimester for their first prenatal care rose significantly in the study area as compared to the control area (24% vs 13%). B) Effects on Interactive Linkage 1. This project made a contribution in making several useful steps in the direction of service integration, namely; i) The health workers have become familiar with procedures on how to work together with each other (especially with a midwife) in carrying out their work in FP/MCH and, ii) The health workers have gotten a feeling of the usefulness of family health records (statistical integration) in identifying targets in their own work and their usefulness in caring for family health. 2. On the other hand, because of a lack of required organizational factors, complete linkage was not obtained as the project intended. i) In regards to the government health worker's activities in terms of home visiting there was not much difference between the study & control areas though the MW did more home visiting than Government health workers. ii) In assessing the service performance of MW & health workers, the midwives balanced their workload between 40% FP, 40% MCH & 20% other activities (mainly immunization). However, $85{\sim}90%$ of the services provided by the health workers were other than FP/MCH, mainly for immunizations such as the encephalitis campaign. In the control area, a similar pattern was observed. Over 75% of their service was other than FP/MCH. Therefore, the pattern shows the health workers are a long way from becoming multipurpose workers even though the government is pushing in this direction. 3. Villagers were much more likely to visit the health sub-center clinic in the study area than in the control area (58% vs.31%) and for more combined care (45% vs.23%). C) Organization factors (admistrative integrative issues) 1. When MW (new workers with higher qualification) were introduced to HSC, it was noted that there were conflicts between the existing HSC workers (Nurse aids with less qualification than MW) and the MW for the beginning period of the project. The cause of the conflict was studied by an anthropologist and it was pointed out that these functional integration problems stemmed from the structural inadequacies of the health subcenter organization as indicated below; i) There is still no general consensus about the objectives and goals of the project between the project staff and the existing health workers. ii) There is no formal linkage between the responsibility of each member's job in the health sub-center. iii) There is still little chance for midwives to play a catalytic role or to establish communicative networks between workers in order to link various knowledge and skills to provide better FP/MCH services in the health sub-center. 2. Based on the above findings the project recommended to the County Chief (who has power to control the administrative staff and the technical staff in his county) the following ; i) In order to solve the conflicts between the individual roles and functions in performing health care activities, there must be goals agreed upon by both. ii) The health sub·center must function as an autonomous organization to undertake the integration health project. In order to do that, it is necessary to support administrative considerations, and to establish a communication system for supervision and to control of the health sub-centers. iii) The administrative organization, tentatively, must be organized to bind the health worker's midwive's and director's jobs by an organic relationship in order to achieve the integrative system under the leadership of health sub-center director. After submitting this observation report, there has been better understanding from frequent meetings & communication between HW/MW in FP/MCH work as the program developed. Lessons learned from the Seosan Project (on issues of FP/MCH integration in Korea); 1) A majority or about 80% of the couples are now practicing FP. As indicated by the study, there is a growing demand from clients for the health system to provide more MCH services than FP in order to maintain the achieved small size of family through FP practice. It is fortunate to see that the government is now formulating a MCH policy for the year 2,000 and revising MCH laws and regulations to emphasize more MCH care for achieving a small size family through family planning practice. 2) Goal consensus in FP/MCH shouBd be made among the health workers It administrators, especially to emphasize the need of care of 'wanted' child. But there is a long way to go to realize the 'real' integration of FP into MCH in Korea, unless there is a structural integration FP/MCH because a categorical FP is still first priority to reduce the rate of population growth for economic reasons but not yet for health/welfare reasons in practice. 3) There should be more financial allocation: (i) a midwife should be made available to help to promote the MCH program and coordinate services, (in) there should be a health sub·center director who can provide leadership training for managing the integrated program. There is a need for 'organizational support', if the decision of integration is made to obtain benefit from both FP & MCH. In other words, costs should be paid equally to both FP/MCH. The integration slogan itself, without the commitment of paying such costs, is powerless to advocate it. 4) Need of management training for middle level health personnel is more acute as the Government has already constructed 90 MCH centers attached to the County Health Center but without adequate manpower, facilities, and guidelines for integrating the work of both FP and MCH. 5) The local government still considers these MCH centers only as delivery centers to take care only of those visiting maternity cases. The MCH center should be a center for the managment of all pregnancies occurring in the community and the promotion of FP with a systematic and effective linkage of resources available in the county such as i.e. Village Health Worker, Community Health Practitioner, Health Sub-center Physicians & Health workers, Doctors and Midwives in MCH center, OBGY Specialists in clinics & hospitals as practiced by the Seosan project at primary health care level.

• 한국유통학회지:유통연구
• /
• 제15권3호
• /
• pp.111-137
• /
• 2010

본 연구는 서비스 시장에서의 지각된 품질과 개인가치간의 인과적 관계 및 고객의 인지욕구에 따른 온 오프라인상의 조절효과에 대해 실증분석하였으며 이를 통해 개인가치에 대한 서비스 전략과 마케팅 관리의 중요성을 제시하고 있다. 서비스 시장에서 서비스 제공자와 구매자간의 장기적 거래관계의 중요성이 크게 부각됨에 따라 관계구축 및 강화에 매우 중요한 역할을 하는 개인가치에 관한 연구는 학계뿐만 아니라 실무적으로도 고객관계관리의 관점에서 시사하는 바가 크다고 할 수 있다. 실증분석을 위해 대형마트(할인점)와 인터넷 쇼핑몰을 이용하는 고객을 대상으로 설문을 통해 데이터를 수집하였으며 온 오프라인의 비교분석을 통한 차이검증을 위한 인과적 구성모델에 대해 구조방정식 모델분석을 통해 가설검증하였다. 구성모델에 대한 분석결과 물리적 환경, 상호작용 품질, 그리고 결과품질로 구성된 지각된 품질은 안정적 삶, 사회적 인식, 사회적 통합으로 구성된 서비스 개인가치에 통계적으로 매우 유의한 정(+)의 영향을 미치는 것으로 나타났으며 집단간 차이효과분석을 통해서도 온 오프라인에 따른 조정효과는 온라인에서보다는 오프라인에서 더 유의한 것으로 나타났다. 그리고 온라인상에서의 서비스에 대한 인지욕구가 높을 때보다는 오프라인상에서의 서비스에 대한 인지욕구가 높을 때 개인가치에 더 유의한 영향을 미치는 것으로 나타났다. 마지막으로 본 연구의 구성모델에 대한 적합도 역시 수용할만한 수준인 것으로 나타났다.

• 한국산림과학회지
• /
• 제16권1호
• /
• pp.1-32
• /
• 1972

본연구(本硏究)는 주요조림수종(主要造林樹種)인 송백류중(松柏類中) 특(特)히 Sub-genus Diploxylon내(內)의 종간교잡(種間交雜)에 의(依)하여 생산(生産)된 일대잡종(一代雜種) ${\times}$P. rigielliottii, ${\times}$P. rigiradiata, ${\times}$P. rigiserotina 및 ${\times}$P. densithunbergii의 임성종자확득율(稔性種字穫得率)을 기준(基準)으로한 교배친화력(交配親和力)과 분류학상(分類學上)의 유연관계(類緣關係)를 검토(檢討)하는 동시(同時)에 조림지(造林地)에 있어서의 생장비교(生長比較), 침엽(針葉)의 외부(外部) 및 해부형태비교(解剖形態比較), phenol성물질(性物質)에 의(依)한 특성비교(特性比較) 및 천연적송림(天然赤松林)에 대(對)한 이입교잡현상등(移入交雜現象等)을 구명(究明)하여 금후계획적조림(今後計劃的造林)에 공헌(貢獻)할 잡종채종림조성(雜種採種林造成) 여부(與否)와 일대잡종(一代雜種)과 그 양친종간(兩親種間)의 차이점(差異點)을 분별관찰(分別觀察)한 결과(結果) 다음과 같은 성적(成績)을 얻었다. 1. 각공시수종(各供試樹種)을 Shaw, Pilger 및 Duffield 등(等)의 분류식(分類式)에 준(準)하여 각조합별(各組合別) 임성종자확득율(稔性種字穫得率)을 기준(基準)으로 교배친화력(交配親和力)과 유연관계(類緣關係)를 검토(檢討)한 바 각조합(各組合)의 양친종간(兩親種間)에는 상당(相當)한 교배친화력(交配親和力)이 있었고, 근연간(近緣間)임을 알수 있었으며, 각조합별(各組合別) 최고임성종자확득율(最高稔性種字穫得率)은 28~58%이었다(표(表) 13). 2. 조림지(稠林地)에 있어서 각일대잡종송(各一代雜種松)의 생장비교(生長比較)에서 특(特)히 ${\times}$P. rigiserotina는 수고(樹高)와 근원경(根元徑)에서 수종간(樹種間)에 1% 수준(水準)으로 고도(高度)의 유의성(有意性)이 있었으므로 재적비(材積比)에서도 종자모수(種字母樹) 보다 109~155%의 보다 월등(越等)한 생장(生長)을 보여 조림상(造林上) 유용성(有用性) 가치(價値)가 있는 우수(優秀)한 일대잡종(一代雜種)으로 기대(期待)되었다(표(表) 16, 17). 3. 각일대잡종송(各一代雜種松)은 내한성(耐寒性)에 있어서 종자모수(種字母樹)의 형질(形質)을 받어 전연(全然) 동해(凍害)를 받지 않았으므로 내한력(耐寒力)이 강(强)함을 알수있었다. 4. 침엽장비교(針葉長比較)에서 일대잡종(一代雜種)의 양친종간(兩親種間)에는 현저(顯著)히 식별(識別)되었으며, 화분모수(花粉母樹)의 형질(形質)을 받은 ${\times}$P. rigiserotina는 종자모수(種字母樹) 보다 65%의 보다큰치(値)를 보여 현저(顯著)하게 식별(識別)되었으나 타일대잡종송(他一代雜種松)은 종자모수(種字母樹)의 형질(形質)을 받어 엽장(葉長)만으로는 잡종성(雜種性)을 용이(容易)하게 식별(識別)하기 어려웠다(표(表) 21). 5. 침엽(針葉)의 해부형태(解剖形態)에 있어서 제형질중(諸形質中) 일부(一部) 예외(例外)도 있었으나 각일대잡종송(各一代雜種松)은 대부분(大部分)이 hypoderm에서 강화(强化)되었고, resin canal에서는 조합(組合)에 따라 종자모수(種字母樹) 또는 화분모수(花粉母樹)의 우성형질(優性形質)을 나타냈으며, fibrovascular bundle에서는 종자모수(種字母樹)와 같이 상이(相離)된 형질(形質)을 나타냈으므로 각일대잡종(各一代雜種)과 그 양친종간(兩親種間)의 식별(識別)이 어느정도(程度) 가능(可能)함을 보았다. 특(特)히 ${\times}$P. densithunbergii에서는 RDI 0.73으로 화분모수(花粉母樹)에 가까운 형질(形質)을 보였다(그림 1, 표(表) 22). 6. Phenol 성물질(性物質)에 의(依)한 특성비교(特性比較)에서 공시일대잡종중(供試一代雜種中) 특(特)히 ${\times}$P. rigielliottii, ${\times}$P. rigiradiata 및 ${\times}$P. rigitaeda는 공(共)히 Rf-0.46인 phenol 물질(物質) 7번(番)이 P. rigida와 동일(同一)하게 담황색(淡黃色)으로 반응(反應)되었으나 화분모수(花粉母樹)에는 반응(反應)이 나타나지 않았으므로 양친간(兩親間)에는 현저(顯著)한 식별(識別)을 할수있었다. 이 결과(結果)는 장차(將次) 차대검정(次代檢定)은 물론(勿論) 교잡육종(交雜育種)에 있어서 잡종성조기식별(雜種性早期識別)의 가능성(可能性)을 보았고, ${\times}$P. rigiserotina와 ${\times}$P. densithunbergii는 양친종(兩親種)과 동일(同一)한 반응(反應)을 나타내어 식별(識別)을 할수없었음을 보아 양친종(兩親種)이 근연간(近緣間)임을 알수있었다(그림 2, 표(表) 23). 7. TLC에 의(依)한 phenol성물질(性物質)의 분리(分離) 및 반응현상(反應現象)은 동일수종내(同一樹種內)에서는 개체별(個體別), 채취부위별(採取部位別), 수령별(樹齡別) 및 화분산지별(花粉産地別)에 관계(關係)없이 동일(同一)한 분리(分離) 및 반응현상(反應現象)을 보였으며, 전개용매(展開溶媒)에 있어서도 Aceton-Chloroform(3:7v/v)을 사용(使用)하였을때나 Benzene-Methanol-Acetic acid(90:16:8 v/v)를 사용(使用)했을때나 동일(同一)한 반응(反應)을 볼수있었다. 8. 천연적송림(天然赤松林)에 있어서의 이입교잡현상(移入交雜現象)은 조사지(調査地) 범위내(範圍內)에서는 동해(東海) 및 서해안지방(西海岸地方)의 각조사임분(各調査林分)의 대부분(大部分)이 잡종성(雜種性)인 사실(事實)과 동해안(東海岸) 보다 서해안지방(西海岸地方)의 조사임분(調査林分)이 월등(越等)히 높은 잡종성(雜種性)임을 알수있었다(표(表) 24, 25). 9. 한국(韓國) 및 일본(日本)에서 선발(選拔)된 수형목(秀型木)은 RDI에 있어서 순수(純粹)한 적송개체(赤松個體)를 발견(發見)할수 없었으며, 본공시목(本供試木)의 전부(全部)가 흑송(黑松)의 형질(形質)을 가진 잡종성(雜種性)임을 알수있었으므로 이러한 수형목(秀型木)은 잡종성(雜種性)에 기인(起因)한 것이라 사료(思料)된다. (그림 3,4, 표(表) 26,27).

• 한국산림과학회지
• /
• 제14권1호
• /
• pp.1-20
• /
• 1972

해외(海外) 선진국(先進國)에서의 임목육종(林木育種)의 실정(實情)과 기(其) 동향(動向)을 견개(見開)하고 금후(今後) 우리나라 임목육종(林木育種)의 취진(就進)에 있어서 반드시 고려(考慮) 또는 실시(實施)되어야할 사항(事項)들에 의하여 고찰(考察)한 결과(結果) 다음과 같은 결론(結論)을 얻었다. 1. 유전자(遺傳子) 보존(保存)을 위한 천연림(天然林)의 보존(保存) 선진제국(先進諸國)에서 천연림(天然林)의 이용개발(利用開發)이 성행(盛行)됨과 아울러 유전자(遺傳子)의 보존(保存)을 목적(目的)으로 하는 일부(一部) 천연림(天然林)의 지역별(地域別) 보존책(保存策)을 채택(採擇)하고 있는 실정(實情)에 비추어서 우리나라와 같이 천연림(天然林)이 거의 탕진(蕩盡)되고 있는 실정하(實情下)에서는 강송(剛松), 잣나무, 섬잣나무, 사시나무, 피나무 등(等) 자생수종(自生樹種)의 천연림(天然林)의 일부(一部)를 유전자보존림(遺傳子保存林)으로 확보(確保)하는 조처(措處)가 긴급(緊急)히 이루어져야할 일이다. 또한 우리나라 고유수종(固有樹種)에 대(對)한 천연림(天然林)의 구성(構成)과 기(其) 발달과정(發達過程)에 대(對)한 연구(硏究)도 근래(近來) 새 수단(手段)으로 등장(登場)한 isozyme의 연구(硏究)에 의(依)하여 수행(遂行)되어야 할 문제(問題)이다. 2. 수형목(秀型木) 수(數)의 증가(增加) 현하(現下) 우리나라의 수형목(秀型木) 수(數)는 기(其) 선발강도(選拔强度)가 지나치게 강(强)하였던 탓으로 그 수(數)가 소(小)하여 이에 의(依)한 채종원(採種園)은 일차조림용(一次造林用)으로는 가(可)하나 이대채종원(二代採種園)을 위(爲)한 모수(母樹)의 선택대상(選擇對象)으로는 중복선발(重複選拔)이 될 우려(憂慮)가 큰 고(故)로 선발강도(選拔强度)를 연화(軟化)하여서 기(其) 본수(本數)를 대폭(大幅) 증가(增加)시킬 필요(必要)가 있다. 3. 차대검정(次代檢定) 특수조합능력(特殊組合能力)을 강조(强調)해야 할 특별(特別)한 경우를 제외(除外)하고는 수형목(秀型木)의 풍매종자(風媒種子)에 의(依)한 차대검정(次代檢定)을 위주(爲主)로 함이 적당(適當)하다고 사료(思料)되나, 차대검정(次代檢定)의 연한(年限) 단축(短縮)을 위(爲)하여서 임목(林木)의 중요형질(重要形質)에 대(對)한 조기검정(早期檢定)에 관(關)한 연구(硏究)가 중요(重要)한 과제(課題)로서 다루어져야만 할것이다. 이와 관련(關聯)하여 zymography의 활용성(活用性) 연구(硏究)도 중요(重要)한 일이다. 4. 유전자형(遺傳子型)과 환경(環境)과의 교호작용(交互作用)에 관(關)한 연구(硏究) 종래(從來) 사실상(事實上) 입지조건(立地條件)이 양호(良好)한 임분(林分)에서 선발(選拔)된 수형목(秀型木)이 요박(療薄)한 임지(林地)에서도 그 우수성(優秀性)을 나타내는지의 여부(如否)를 구명(究明)하므로서 특수입지(特殊立地)를 위(爲)한 별도채종원조성(別途採種園造成)의 필요성(必要性) 유무(有無)를 하루속(速)히 구명(究明)해야하며 우리나라의 육종구(育種區)에 대(對)한 재확인(再確認)과 그 적용(適用)이 요청(要請)되는 일이다. 5. 윤엽수(潤葉樹)의 채종원(採種園) 천연림(天然林)의 구성분자(構成分子)로서 생장력(生長力)의 비교(比較)가 곤란(困難)한 윤엽수(潤葉樹)에 대(對)하여서는 외국(外國)에서 실시(實施)하는 바를 참고(參考)하여 선발목간(選拔木間)의 교잡차대(交雜次代)로서 차대검정림(次代檢定林)을 설치(設置)한후 이를 도태(陶汰) seedling seed orchard로 유도(誘導)하는 방법(方法)을 취(取)함이 가(可)하다고 사료(思料)된다. 6. 내병충성(耐病蟲性) 육종(育種) 소나무좀벌레, 솔잎흑파리 등(等) 충해(蟲害)와 낙엽송(落葉松)의 낙엽병(落葉病)과 포푸라 현병(鉉病) 등(等)은 유전자(遺傳子)에 의(依)하여 지배(支配)되는 것이 구명(究明)되고 있어 이에 대(對)한 내병충성(耐病蟲性) 육종(育種)을 계획실시(計劃實施)함을 요(要)한다. 7. 재질(材質) 특(特)히 목재비중(木材比重)에 대(對)한 육종(育種) 특(特)히 pulp 용재(用材)를 목적(目的)으로 하는 수종(樹種)에 대(對)하여서는 선진각국(先進各國)에 비추어서 목재비중(木材比重)에 대(對)한 육종(育種)의 실시(實施)가 요청(要請)된다. 8. 삼나무(Cryptomeria japonica) 및 편백(Chamaecyparis obtusa)의 도입(導入) 삼나무와 편백은 현재(現在) 남부(南部) 난대지대(暖帶地帶)에 국한(局限)하여 조림(造林)하고 있으나 일본(日本)에 있어서의 양수종(兩樹種)의 조림한계(造林限界)가 예상이상(豫想以上)으로 한냉(寒冷)한 지대(地帶)까지 실시(實施)되고 있는 실정(實定)에 비추어서 상기(上記) 양수종(兩樹種)에 대(對)한 도입시험(導入試驗)을 종래(從來)보는 한냉(寒冷)한 지대(地帶)까지 확대실시(擴大實施)할 필요(必要)가 있다고 인정(認定)되었다.

• 한국습지학회지
• /
• 제18권4호
• /
• pp.474-480
• /
• 2016

본 연구에서는 지구적 차원에서 생물다양성의 성립 배경과 그동안 일어난 변화 그리고 기후변화가 생물다양성 및 인간에 미치는 영향을 밝히고 그 영향을 줄이기 위한 대안을 제시하였다. 생물다양성은 생명체의 풍부한 정도이며, 생물을 구분하는 모든 수준에서의 다양성을 종합적으로 의미한다. 즉, 생물다양성은 유전자, 종 그리고 생태계 전반과 그들의 상호작용을 아우른다. 이는 생태계의 기반을 구성하며, 모든 사람들이 필수적으로 의존하는 서비스를 제공한다. 그럼에도 불구하고 오늘날 생물다양성은 주로 인간 활동에 의해 점점 더 위협받고 있다. 지구상의 생물은 생명이 탄생한 이래 약 40억년의 역사를 통해 다양한 환경에 적응하고 진화한 결과, 약 1000만 내지 3000만종으로 추정되는 다양한 생물이 존재하게 되었다. 생물다양성을 구성하는 무수한 생명들은 각각의 고유한 특성을 가지고 있으며 다양한 관계 속에 얽혀 있다. 우리들이 현재 생활하고 있는 지구의 환경도 이러한 생물체의 방대한 연관성과 상호작용에 의해 긴 세월 동안 만들어져 왔으며, 인류도 하나의 생물로서 다른 생물들과 관계를 맺으며 살아가고 있다. 이러한 주위의 생물들이 없다면 사람도 살아갈 수 없다. 그러나 인류는 최근 수 백 년 간 과거의 평균 멸종속도를 1000배 가량이나 가속시켜 왔다. 우리는 미래 세대의 풍요로운 삶을 위해서라도 생물다양성을 보전하는 한편, 지속가능하게 이용할 책임이 있다. 우리나라는 세계 어느 국가보다도 빠른 경제 성장을 이루어왔으나, 동시에 이는 남북으로 길게 뻗은 반도 국가라는 지리적 특성에 의해 본래 풍부했던 생물다양성을 빠르게 소실시키는 결과를 야기하였다. 한국인은 오랫동안 농업, 임업 그리고 어업을 해오는 과정에서 자연과의 공존을 통해 독특한 고유의 문화를 창조하였다. 그러나 근래 서구문명의 유입과 과학 기술의 발전 과정에서 이러한 자연과의 관계는 멀어지게 되었으며, 자연과 문화 사이의 조화로운 조합에 의해 창출된 고유한 풍토는 점점 더 사라지고 있다. 한국의 인구는 세계 인구가 지속적으로 증가하는 것과는 반대로 점차 줄어들 것으로 예측되고 있다. 이 시점에서 우리는 인구 감소에 의한 자연의 회복에 발맞추어 급속한 인구 증가 및 경제 성장으로 인해 훼손된 생물다양성을 복원할 필요가 있다. 지구상에 생명이 탄생한 이래 다섯차례의 대멸종이 있었다. 현대의 대멸종은 매우 급속히 진행되고 있으며, 인간 활동에 의한 영향이 주요 원인인 점에서 이전의 것과 구분된다. 기후변화는 실제로 일어나고 있으며, 생물다양성은 이러한 변화에 매우 취약하다. 만약 생명체가 변화하는 환경에서 '진화를 통한 적응', '생존가능한 다른 지역으로의 이주' 등과 같은 생존 방법을 찾아내지 못한다면 이들은 절멸할 것이므로, 기후변화가 지속된다면 생물다양성은 극도로 훼손될 수 밖에 없다. 따라서 우리는 이러한 훼손정도를 최소화하기 위해 기후변화가 생물다양성에 미치는 영향을 보다 적극적이고 심도있게 파악할 필요가 있다. 생물계절의 변화, 식생 이동을 비롯한 분포 범위의 변화, 생물 간 상호작용의 부조화, 먹이 사슬 이상에 기인한 번식 및 생장률 감소, 산호초 백화현상 등이 기후변화에 미치는 영향으로 등장하고 있다. 질병의 확산, 식량 생산 감소, 작물 경작지 범위 변화, 어장 및 어업시기의 변화 등은 인간에 대한 영향으로 나타나고 있다. 기후변화 문제를 해결하기 위해 우선, 우리는 온실 가스 배출량을 감소시켜 기후변화 완화를 시도할 필요가 있다. 그러나 현재 우리가 온실가스 배출을 당장 멈추더라도, 기후변화는 당분간 지속될 전망이다. 이런 점에서, 기후변화 적응 전략을 준비하는 것이 더 현실적이 될 수 있다. 생물다양성에 대한 기후변화 영향의 지속적 모니터링 및 보다 적합한 모니터링 체계 구축이 선행과제가 될 수 있다. 생물다양성이 성립할 수 있는 생태적 공간의 확보, 이동 보조 및 남북을 이어주는 수평 및 저지대와 고지대를 이어주는 수직적 생태네트웍이 기후변화에 따른 생물다양성의 적응을 돕는 대안으로 추천될 수 있다.

• 한국유통학회지:유통연구
• /
• 제16권2호
• /
• pp.119-138
• /
• 2011

지난 십년동안 인터넷을 통한 전자상거래는 빠른 속도로 성장해 왔다. 이러한 인터넷의 발달은 기업들의 사업방식에 많은 변화를 유도했으며, 그 중에서도 마케팅경로의 구조와 경로 구성원들 사이의 관계에 중요한 변화를 초래하고 있다. 각 기업이 처한 시장환경은 다양하며 이 다양한 시장 환경은 인터넷 경로가 각 시장에 미치는 효과를 조절하는 역할을 한다. 이러한 시장의 다양성에도 불구하고 지금까지의 선행연구들은 각기 특정한 하나의 시장상황(unique setting)을 상정하여 인터넷경로 도입이 그 시장에 미치는 영향을 분석하는데 그쳐왔다. 이러한 기존 연구의 공백을 채우기 위해 본 연구는 시장의 다양성을 소비자의 지리적 분포, 시장의 인터넷 수용도의 측면에서 살펴보고 이러한 시장 환경이 인터넷 경로 도입 효과에 미치는 영향에 관하여 조사해 보고자 한다. 이를 위해 본 연구는 다양한 소비자들의 지리적 분포, 경쟁강도, 소비자의 인터넷 상거래에 대한 수용도 등을 포함한 다양한 시장 환경을 수요모형에 반영시켜 그 영향력 분석을 가능하도록 하였다. 그러나, 다양한 시장 요소를 모형에 반영하는 과정에서 수요모형이 복잡한 구조를 가지게 되었다. 이 문제를 극복하고 게임이론의 균형해를 도출하기 위해 Newton-Raphson algorithm을 사용한 numerical search 방법을 사용하였다. 분석결과 두 종류의 경로에 대한 소비자선호의 분포에 따라 생산자의 가격차별정도, 생산자와 독립소매상 간의 경로이윤 배분율, 그리고 인터넷경로 도입이 각 경로주체의 이윤 향상에 도움이 되는지의 여부, 소비자잉여 등이 달라질 수 있음을 발견하였다. 끝으로 연구의 학술적, 실무적 시사점과 한계점 및 향후 연구방향도 논의되었다.

• 인터넷정보학회논문지
• /
• 제14권5호
• /
• pp.69-76
• /
• 2013

세계적으로 전파력과 병원성이 높은 신종인플루엔자, 조류독감 등과 같은 전염병이 증가하고 있다. 전염병이란 특정 병원체(pathogen)로 인하여 발생하는 질병으로 감염된 사람으로부터 감수성이 있는 숙주(사람)에게 감염되는 질환을 의미한다. 전염병의 병원체는 세균, 스피로헤타, 리케차, 바이러스, 진균, 기생충 등이 있으며, 호흡기계 질환, 위장관 질환, 간질환, 급성 열성 질환 등을 일으킨다. 전파 방법은 식품이나 식수, 곤충 매개, 호흡에 의한 병원체의 흡입, 다른 사람과의 접촉 등 다양한 경로를 통해 발생한다. 전 세계의 대부분 국가들은 전염병의 전파를 예측하고 대비하기 위해서 수학적 모델을 사용하고 있다. 하지만 과거와 달리 현대 사회는 지상과 지하 교통수단의 발달로 전염병의 전파 속도가 매우 복잡하고 빨라졌기 때문에 우리는 이를 예방하기 위한 대책 마련의 시간이 부족하다. 그러므로 전염병의 확산을 막기 위해서는 전염병의 전파 경로를 예측할 수 있는 시스템이 필요하다. 우리는 이러한 문제를 해결하기 위해서 전염병의 실시간 감시 및 관리를 위한 전염병의 감염 경로 추적 및 예측이 가능한 통합정보 시스템을 구현하였다. 이 논문에서는 전염병의 전파경로 예측에 관한 부분을 다루며, 이 시스템은 기존의 수학적 모델인 Susceptible - Infectious - Recovered (SIR) 모델을 기반으로 하였다. 이 모델의 특징은 교통수단인 버스, 기차, 승용차, 비행기를 포함시킴으로써, 도시내 뿐만 아니라 도시간의 교통수단을 이용한 이동으로 사람간의 접촉을 표현할 수 있다. 그리고 한국의 지리적 특성에 맞도록 실제 자료를 수정하였기 때문에 한국의 현실을 잘 반영할 수 있다. 또한 백신은 시간에 따라서 투여 지역과 양을 조절할 수 있기 때문에 사용자가 시뮬레이션을 통해서 어느 시점에서 어느 지역에 우선적으로 투여할지 백신을 컨트롤할 수 있다. 시뮬레이션은 몇가지 가정과 시나리오를 기반으로 한다. 그리고 통계청의 자료를 이용해서 인구 이동이 많은 주요 5개 도시인 서울, 인천국제공항, 강릉, 평창, 원주를 선정했다. 상기 도시들은 네트워크로 연결되어있으며 4가지의 교통수단들만 이용하여 전파된다고 가정하였다. 교통량은 국가통계포털에서 일일 교통량 자료를 입수하였으며, 각도시의 인구수는 통계청에서 통계자료를 입수하였다. 그리고 질병관리본부에서는 신종인플루엔자 A의 자료를 입수하였으며, 항공포털시스템에서는 항공 통계자료를 입수하였다. 이처럼 일일 교통량, 인구 통계, 신종인플루엔자 A 그리고 항공 통계자료는 한국의 지리적 특성에 맞도록 수정하여 현실에 가까운 가정과 시나리오를 바탕으로 하였다. 시뮬레이션은 신종인플루엔자 A가 인천공항에 발생하였을 때, 백신이 투여되지 않은 경우, 서울과 평창에 각각 백신이 투여된 경우의 3가지 시나리오에 대해서, 감염자가 피크인 날짜와 I (infectious)의 비율을 비교하였다. 그 결과 백신이 투여되지 않은 경우, 감염자가 피크인 날짜는 교통량이 가장 많은 서울에서 37일로 가장 빠르고, 교통량이 가장 적은 평창에서 43일로 가장 느렸다. I의 비율은 서울에서 가장 높았고, 평창에서 가장 낮았다. 서울에 백신이 투여된 경우, 감염자가 피크인 날짜는 서울이 37일로 가장 빨랐으며, 평창은 43일로 가장 느렸다. 그리고 I의 비율은 강릉에서 가장 높으며, 평창에서 가장 낮았다. 평창에 백신을 투여한 경우, 감염자가 피크인 날짜는 37일로 서울이 가장 빠르고 평창은 43일로 가장 느렸다. I의 비율은 강릉에서 가장 높았고, 평창에서는 가장 낮았다. 이 결과로부터 신종인플루엔자 A가 발생하면 각 도시는 교통량에 의해 영향을 받아 확산된다는 것을 확인할 수 있다. 따라서 전염병 발생시 전파 경로는 각 도시의 교통량에 따라서 달라지므로, 교통량의 분석을 통해서 전염병의 전파 경로를 추적하고 예측함으로써 전염병에 대한 대책이 가능할 것이다.