• 한국정보통신설비학회:학술대회논문집
• /
• 2005.08a
• /
• pp.141-145
• /
• 2005

In this paper, UWB system did research about effect that interference effect with neighborhood single equipment or nearby group equipment gets In DMB service. 2.6425GHz satellite digital multimedia broadcasting service(SDMB) that electric wave interference special quality is contiguity frequency-band including interference of signal by unnecessary radiation level that is radiated in UWB system, and 3.4125GHz broadcasting relay net that is In-band frequency-band and interference effect degree that get in service did comparative analysis. SDMB system was BER $1{\times}10^{-4}$ that interference effect happens from 6.5m point and broadcasting signal reception is possible at 4m point. Also, it was BER $1{\times}10^{-4}$ that interference effect begins to happen from 5.0m point about center frequency 3.4126GHz and broadcasting signal reception is possible at 2m point. And, confirmed that UWB system of impulse method is less interference effect about 2 dB than UWB system of OFDM method, to electric wave of UWB system that is small output

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.78-81
• /
• 2000

A new type low-pass filter design method based on a coupled line and transmission line theory is proposed to suppress harmonics by attenuation poles in the stop band The design formula are derived using the equivalent circuit of a coupled transmission line. The new low-pass filter structure is shown to have attractive properties such as compact size, wide stop band range and low insertion loss. The seventh-order low-pass filter designed by present method Ins a cutoff frequency of 0.9 GHz with a 0.01 dB ripple level. The coupled line type low-pass filter with stripline configuration was fabricated by using a high-temperature superconducting (HTS ; $YBa_2Cu_3O_{7-x}$) thin film on MgO(100) substrate. Since the HTS coupled line type low-pass filter was proposed with five attenuation poles in stop band such as 1.8, 2.5, 4, 5.5, 62 GHz. The fabricated low-pass filter has improved the attenuation characteristics up to seven times of the cutoff frequency Bemuse of good rejection of the spurious signals and harmonics, our low-pass filter is applicable to mobile base station systems such as cellular, personal communication systems and international mobile telecommunication(IMT)-2000 systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1279-1290
• /
• 2007

In this paper, a cylindrical hybrid antenna which is spatially fed by an off-set linear feed array is described to form complex beam patterns. The linear feed array consists of twelve micro-strip patch elements and forms a flat-topped beam pattern with a beam-width of $90^{\circ}$ in the horizontal plane. The vertical curve on the cylindrical reflector with the linear feed array is shaped in order to form a cosecant beam pattern within the range of $-5^{\circ}$ to $-25^{\circ}$ in the vertical plane. To form complex beam patterns, the hybrid antenna with cylindrical reflector aperture of $140{\times}50\;cm$ was designed and fabricated to be operated within the IMT 2000 service band, and also electrical performances of the antenna were measured and analyzed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1262-1270
• /
• 2007

In this paper, we propose a new distortion cancellation mechanism for a balanced power amplifier structure using the carrier cancellation loop of a feedforward and post-distortion technique. The proposed cross post-distortion balanced linear amplifier can reduce nonlinear components as much as the conventional feedforward amplifier through the output dynamic range and broad bandwidth. Also the proposed system provides higher efficiency than the feedforward. The capacities of power amplifier and error power amplifier in the proposed system are analyzed and compared with those of feedforward amplifier. Also the operation mechanisms of the three kind loops are explained. The proposed cross post-distortion balanced linear power amplifier is implemented at the IMT-2000($f_0=2.14\;GHz$) band. With the commercial high power amplifiers of total power of 240 W peak envelope power fer base-station application, the adjacent channel leakage ratio measurement with wideband code division multiple access 4FA signal shows 18.6 dB improvement at an average output power of 40 dBm. The efficiency of fabricated amplifier Improves about 2 % than the conventional feedforward amplifier.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1186-1193
• /
• 2005

In this paper, a new 3 dB branch line hybrid using asymmetric spiral-shaped defected ground structure(DGS) microstrip is proposed. The proposed branch line hybrid suppresses the 2nd and the 3rd harmonic component effectively. Also a DGS $\lambda$/4 bias line that can suppress high frequency harmonics as well as low frequency intermodulation component is proposed. With the harmonic termination tuner using the proposed hybrid and the harmonic blocking bias line, the 2nd and the 3rd harmonic components of the fabricated amplifier that operated in IMT-2000 basestation transmitting band were suppressed up 25 dB and 27 dB, respectively. The proposed harmonic load-pull setup of amplifier is more easily accomplished with proposed circuits than the previous.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2003.05a
• /
• pp.92-96
• /
• 2003

In this paper, 30 W power Amplifier for IMT-2000 repeater was developed gain flatness and the third IMD (Intermodulation distortion) by Microwave absorber. The absorption ability of the absorber is measured up to -10 ㏈ and -4 ㏈ at 3.6 ㎓, 2.3 ㎓ band respectively. Non using absorber power amplifier has the gain over 57 ㏈, the gain flatness of ${\pm}$0.33 ㏈ and the third IMD of 27 ㏈c at 33.3 W output. Otherwise, using absorber power amplifier has the gain over 58㏈, the gain flatness of less than ${\pm}$0.9, the third IMD over 29 ㏈c at the same output power. As a result, the characteristic of the different type show improvement of 1 ㏈ in gain, 0.3 ㏈ in Gain flatness and 1.77 ㏈c in IMD.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1071-1078
• /
• 2003

In this paper, the planar, compact, and broadband phased array antenna system for IMT-2000 applications has been investigated. Two methods far designing a low-cost and low-complex beam-farming network are proposed. First, a new compact and broadband phase shifter with continuously controlled phase bits is designed by using parallel coupled lines. Second, its equivalent phase delay line is suggested to be capable of replacing the complex phase shifter with a reference phase bit on a phased array antenna. For the purpose of achieving the broadband system, in addition to the broadband phase shifter, a wide-slot antenna with a ground reflector is utilized as an element antenna. Therefore, the phased array antenna system has achieved compact size, broad bandwidth, and wide steering angle, although it has low complexity and low fabrication cost. The 3${\times}$1 phased array antenna system has a compact size of 1.6 λ${\times}$ l.6 λ, which is the sufficient ground plane of the wide-slot antenna. Experimental results present that the S$\_$11/ has less than 15 dB within the band and its radiation patterns on an E-plane have the capability of steering an antenna beam from -29$^{\circ}$to +30$^{\circ}$.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.12-24
• /
• 2001

The key advantage of LTCC(low temperature co-fired ceramics) technology is the ability to integrate passive components such as resistors, capacitors, and inductors. More compact circuits with an increased scale of integration are needed with the development for advanced telecommunication system such as IMT-2000. LTCC technology can be obtained by removing these elements from the substrate surface to inside of ceramic body. And it can miniaturize the wireless phone through integration of planar patch antenna, duplexer, band pass filter, bias line, circuit of impedance matching and RF choke etc. Futhermore, with the multilayer chip process and its outstanding electrical material characteristics, LTCC is predestined for highly-integrated, cost effective wide band applications. This paper focuses on the general description of LTCC MCM technologies and the fabrication of the multilayer VCO module.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.87-90
• /
• 2003

In this paper, A feedforward linear power amplifier is analyzed for imperfect signal cancellation and negative feedback for basestaion of IMT2000 band. the distortion generatied by the error amplifier is reduced using an imperfect signal cancellation for a 1-carrier WCDMA source by 4.3dB at 2.5MHz offset and 6dB at 5MHz offset of IMSR(intermodulation signal power ratio) compared to a perfect signal cancellation system. additionally, An imperfect signal cancellation using negative feedback improved 1.3dB and 8.2dB at 2.5MHz and 5MHz offset of IMSR compared to an imperfect signal cancellation.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.3
• /
• pp.180-185
• /
• 2005

Microstrip antennas generally have a lot of advantages that are thin profile, lightweight, low cost, and conformability to a shaped surface application with integrated circuitry. In addition to military applications, they have become attractive candidates in a variety of commercial applications such as mobile satellite communications, the direct broadcast system (DBS), global positioning system (GPS), and remote sensing. Recently, many of the researches have been achieved for improving the impedance bandwidth of microstrip antennas. The basic form of the microstrip antenna, consisting of a conducting patch printed on a grounded substrate, has an impedance bandwidth of $1\~2\%$. For improvement of narrow bandwidth of microstrip patch, we were designed U-slot microstrip patch antenna in this paper. This antenna had wide bandwidth for all personal communication services (PCS) and IMT-2000. For the design of U-slot microstrip patch antenna using a finite difference time domain(FDTD) method. This numerical method could get the frequency property of U-slot patch antenna and the electromagnetic fields of slots.