• Journal of Computing Science and Engineering
• /
• v.8 no.3
• /
• pp.129-136
• /
• 2014

This paper presents the equivalent circuit modelling and eigenfrequency analysis of a wideband robust capacitive radio frequency (RF) microelectromechanical system (MEMS) switch that was designed using Poly-Si and Au layer membrane for highly reliable switching operation. The circuit characterization includes the extraction of resistance, inductance, on and off state capacitance, and Q-factor. The first six eigenfrequencies are analyzed using a finite element modeler, and the equivalent modes are demonstrated. The switch is optimized for millimeter wave frequencies, which indicate excellent RF performance with isolation of more than 55 dB and a low insertion loss of 0.1 dB in the V-band. The designed switch actuates at 13.2 V. The R, L, C and Q-factor are simulated using Y-matrix data over a frequency sweep of 20-100 GHz. The proposed switch has various applications in satellite communication networks and can also be used for devices that will incorporate the upcoming IEEE Wi-Fi 802.11ad protocol.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.1B
• /
• pp.67-73
• /
• 2009

This paper proposes a new fast vertical handover mechanism to optimize and enhance the existing fast vertical handover HMIPv6(FV-HMIP) mechanism in heterogeneous wireless access networks. The proposed mechanism ad opts the IEEE 802.21 Media Independent Handover Function(MIHF), and thus is called the "MFV-HMIP". The Media Independent Handover Service (MIIS) in the IEEE 802.21 MIHF is extended by including new L3 inform ation to provide domain prefixes of heterogeneous neighbouring mobility anchor points(MAPs). This can eliminate the heterogeneous neighbouring MAP discovery phase in the existing FV-HMIP. Thus, the proposed MFV-HMIP can reduce the signalling traffic over wireless link and increase the possibility of predictive mode operation. Therefore, the proposed MFV-HMIP mechanism can be superior to the existing FV-HMIP mechanism for wireless resource efficiency, handover latency, and packet loss. Through analytic performance evaluations and computer si mulations, the proposed mechanism can be shown to optimize and enhance the existing mechanism.

• Journal of Communications and Networks
• /
• v.14 no.1
• /
• pp.63-74
• /
• 2012

Multicast data communication is an efficient communication scheme, especially inmulti-hop ad hoc networks where the media access control (MAC) layer is based on one-hop broadcast from one source to multiple receivers. Compared to unicast, multicast over a wireless channel should be able to deal with varying channel conditions of multiple users and user mobility to provide good quality to all users. IEEE 802.11 does not support reliable multicast owing to its inability to exchange request-to-send/clear-to-send and acknowledgement packets with multiple recipients. Thus, several MAC layer protocols have been proposed to provide reliable multicast. However, additional overhead is introduced, as a result, which degrades the system performance. In this paper, we propose an efficient wireless multicast MAC protocol with small control overhead required for reliable multicast in multi-hop wireless ad hoc networks. We present analytical formulations of the system throughput and delay associated with the overhead.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.31-34
• /
• 2002

There are two kinds of network architectures in the IEEE 802.11:[1] distributed (ad-hoc) or centralized (infrastructure) wireless network. Centralized networks have an access point (base station) that can control the wireless medium access of stations in these networks. The 802.11 MAC protocol of an access point is the same as those of other stations in the contention period. This paper propose a novel MAC protocol of an access point to solve these problems. This MAC protocol adds a new contention-free period called EPCF (Extended PCF) to resolve accumulated data in the queue of an access point. Simulation results show that the new protocol performs better throughput than the 802.11 standard MAC with the less queue memory site requirement.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.3 no.1
• /
• pp.26-51
• /
• 2009

In this paper, we propose an empirical framework for modeling and emulating interference in multi-hop wireless ad-hoc networks. Wireless interference causes wide variation in the frame delivery rate at a link, and thus we cannot represent the state of the link with only two states, connected state and disconnected state, as in wired networks. We first investigate wireless interference in detail, in order to accurately calibrate the interference and identify its underlying attributes, and then we simulate the diverse occurrences and effects of interference, after incorporating the scheme into a simulation tool. Based on these observations, we devise a modeling and simulation framework with several control parameters, and perform an extensive set of simulation studies. The simulation results indicate that the proposed framework enables us to examine various attributes of wireless interferences and their effects on wireless network protocols and systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.1
• /
• pp.119-124
• /
• 2010

The MAC layer in ad-hoc network which makes network of nodes without infrastructure for a time has became an issue to reduce delay, allocate fairly bandwidth, control TX/RX power and improve throughput. Specially, the problem to reduce power consumption in ad-hoc network is very important part as ad-hoc devices use the limited battery. For solution of the problem, many power control algorithms, such as distribute power control, PCM (Power Control MAC) and F-PCF (Fragmentation based PCM), are proposed to limit power consumption until now. Although the algorithms are designed to minimize power consumption, the latency communication zone is generated by power control of RX/TX nodes. However the algorithms don't suitably reuse the space. In this paper proposes the algorithm to improve data throughput through Spatial Reuse based on a power control method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.7B
• /
• pp.602-607
• /
• 2006

A subscriber-oriented service became necessary for the QoS management due to the development of network. BcN(Broadband convergence Network) which incorporates communication, broadcasting and internet not only improves the quality of the communication and broadcasting service but also. aims at broadband service. Therefore, QoS management for each subscriber becomes more important. Not yet, however, the discussion for the subscriber oriented QoS management is not activated. Although, there are several techniques for subscriber distinction using flow information, IP information or MAC information, but they are only processed in layer 3 network. Actually, it is impossible to manage QoS of all subscriber's in layer 3 network. In this paper, we propose a method for QoS management scheme that does not need additional processes or large hardware in layer 2 network and analyze efficiency and overheads. We propose the first subscriber-oriented service method in layer 2 network that is applicable to either existing network or BcN.

• Journal of information and communication convergence engineering
• /
• v.7 no.3
• /
• pp.399-403
• /
• 2009

In IEEE 802.15.1 (Bluetooth) Ad-hoc networks, the frequency is resolved by the specific part of the digits of the Device clock and the Bluetooth address of the Master device in a given piconet. The piconet performs a fast frequency hopping scheme over 79 carriers of 1-MHz bandwidth. Since there is no coordination between different piconets, packet collisions may occur if two piconets are located near one another. In this paper, we proposed a software/hardware co-design of an adaptive frequency decision mechanism so that more than two different kinds of wireless devices can stay connected without frequency collision. Suggested method was implemented with C program and HDL (Hardware Description Language) and automatically synthesized and laid out. The adaptive frequency hopping circuit was implemented in a prototype and showed its operation at 24MHz correctly.

• Journal of Communications and Networks
• /
• v.13 no.5
• /
• pp.421-427
• /
• 2011

Problems encountered in IEEE 802.11 medium access control (MAC) design are interferences from neighboring or hidden nodes and collision from simultaneous transmissions within the same contention floors. This paper presents the selective decoding schemes in MAC protocol for multiple input multiple output ad-hoc networks. It is able to mitigate interferences by using a developed minimum mean-squared error technique. This interference mitigation combined with the maximum likelihood decoding schemes for the Alamouti coding enables the receiver to decode and differentiate the desired data streams from co-channel data streams. As a result, it allows a pair of simultaneous transmissions to the same or different nodes which yields the network utilization increase. Moreover, the presented three decoding schemes and time line operations are optimally selected corresponding to the transmission demand of neighboring nodes to avoid collision. The selection is determined by the number of request to send (RTS) packets and the type of clear to send packets. Both theoretical channel capacity and simulation results show that the proposed selective decoding scheme MAC protocol outperforms the mitigation interference using multiple antennas and the parallel RTS processing protocols for the cases of (1) single data stream and (2) two independent data streams which are simultaneously transmitted by two independent transmitters.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.1 no.2
• /
• pp.104-112
• /
• 2006

ZigBee is the emerging industrial standard for ad hoc networks based on IEEE 802.15.4. It is used for low data rate and low power wireless network applications. Expected applications of ZigBee include wireless sensor networks for remote monitoring, home control, and industrial automation. Since one of the most important design goals of ZigBee is to reduce the installation and running costs, the ZigBee stack is embedded in the cheap and small micro-controller unit. The hierarchical routing algorithm is used for ZigBee end devices which have very limited resources. Using the block addressing scheme, end devices can send data to the destination without a routing table. However, hierarchical routing has the problem that the packets follow the tree hierarchy to the destination even if the destination is located nearby. In this paper, we propose a scheme to improve the hierarchical routing algorithm in ZigBee networks by employing the neighbor table that is originally used together with the routing table. We suggest selecting the neighbor node that has the minimum remaining hops to the destination as the next hop node. Simulation result shows that the proposed scheme saves more than 30% of the hop counts compared with the original hierarchical routing.