• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.75-79
• /
• 1997

Optical and mechanical characteristics of $TiO-2, ZrO_2 \;and\; SiO_xN_y$ thin films prepared by ion assisted deposition (IAD) were investigated. IAD films were bombarded by Ar or nitrogen ion beam from a Kaufman ion source while they were grown in as e-beam evaporator. The result shows that the Ae IAD increases the refractive index and packing density of $TiO_2 films close to those of the bulk. For $ZrO_2$ films the Ar IAD increases the average refractive index decreases the negative inhomogeneity of refractive index and reverses to the positive inhomogeneity. The optical properties result from improved packing density and denser outer layer next to air The Ar-ion bombardment also induces the changes in microstructure of $ZrO_2$ films such as the preferred (111) orientation of cubic phase increase in compressive stress and reduction of surface roughness. Inhomogeneous refractive index SiOxNy films were also prepared by nitrogen IAD and variable refractive index of $SiO_xN_y$ film was applied to fabricate a rugate filter.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.37-41
• /
• 1997

The optical property, the environmental stability and the crystallization of ZnS thin films prepared by ion-assisted deposition (IAD) were investigated and compared with those of conventional electron-beam deposited thin films. The humidity(R.H. 85%) test and the thermal(15$0^{\circ}C$) show that the IAD films have relatively higher refractive index, smaller extinction coefficient and environmentally more stable than the conventional films. It is believed to originate from the reduced adsorption of moisture which reflect the increased packing density and the improved microstructure by ion bombardment. XRD experiments also confirm that conventionally grown films have an amorphous in comparison with the crystalline structured IAD films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.103-106
• /
• 2006

Semiconductor laser diode has a reflective facet in a both-ends side fundamentally. Laser performance for improving, Anti-Reflection and High-reflection coating on the facet of semiconductor laser diode. To prevent internal feedback from both facets for realizing superluminescent diode and reducing the reflection-induced intensity noise of laser diode, it's key techniques are AR/HR coatings. In the study AR coating film were manufactured by Ion-Assisted Deposition(IAD) system. Then manufactured coating film measurement electrical properties(L-I-V, Se, Resistor) and Optical properties (wavelength FFP)

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.1
• /
• pp.24-28
• /
• 2010

We have proposed an Buffer layer to improve the transmittance of ITO. Here, $SiO_2$ and $TiO_2$ were selected as the Buffer layer coating material. The structures of Buffer layer were designed in ITO/$SiO_2/TiO_2$/Glass and ITO/Glass/$TiO_2/SiO_2$. Then, these materials were deposited by ion-assisted deposition system. Transmittances of deposited ITO were 86.14 and 85.07%, respectively. These results show that the proposed structure has higher transmittance than the conventional ITO device.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.98-98
• /
• 1999

Highly transparent and conducting tin-doped indium oxide (ITO) films were deposited on polycarbonate substrate by ion-assited deposition. Low substrate temperature (<10$0^{\circ}C$) was maintained during deposition to prevent the polycarbonate substrate from be deformed. The influence of ion beam energy, ion current density, and tin doping, on the structural, electrical and optical properties of deposited films was investigated. Indium oxide and tin-doped indium oxide (9 wt% SnO2) sources were evaporated with assisting ionized oxygen in high vacuum chamber at a pressure of 2$\times$10-5 torr and deposition temperature was varied from room temperature to 10$0^{\circ}C$. Oxygen gas was ionized and accelerated by cold hallow-cathode type ion gun at oxygen flow rate of 1 sccm(ml/min). Ion bea potential and ion current of oxygen ions was changed from 0 to 700 V and from 0.54 to 1.62 $\mu$A. The change of microstructure of deposited films was examined by XRD and SEM. The electrical resistivity and optical transmittance were measured by four-point porbe and conventional spectrophotometer. From the results of spectrophotometer, both the refractive index and the extinction coefficient were derived.

• Korean Journal of Optics and Photonics
• /
• v.8 no.5
• /
• pp.382-386
• /
• 1997

The composite $MgF_2$-$TiO_2$ films are fabricated by codeposition from two independent sources. To improve optical and mechanical properties of films, the films are prepared by ion-assisted deposition. Chemical compositions, optical properties and microstructures of the composite films were investigated. The chemical composition rates of Ti:Mg of $MgF_2$-$TiO_2$ composite films are nonlinearly varied according to the relative deposition rate. It is found that the refractive indices of the composite films decrease with increasing $MgF_2$ contents and can be fitted quite well with Drude's formula and that the microstructures of the composite films changes from an amorphous to crystalline with increasing $MgF_2$ mole fractions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.169-169
• /
• 2010

650nm 적외선 차단 필터를 Macleod 프로그램을 이용하여 설계하고, 이온보조증착(IAD) 장비를 이용하여 코팅한 후 투과도, 파장, 두께특성을 조사하였다. 차단필터의 증착물질은 $TiO_2$ (n=2.30) /$SiO_2$ (n=1.46) 을 사용하여 45층의 다층 박막으로 증착하였다. 코팅된 차단필터는 차단파장이 651 nm로써 평균 ${\pm}5$ nm 이내의 편차를 보였다. 420~630 nm 파장영역에서 평균 투과도는 89%이었으며, 투과도의 균일도는 약 2.12로써 매우 균일하였다. 투과도기 단파장 영역에서 감소된 것은 다층박막 증착 시 산소가 결핍된 것으로 판단된다.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.788-796
• /
• 1996

$TiO_2$ films prepared by RF magnetron sputtering, electron beam evaporation, ion assisted deposition (IAD) and sol-gel method are prepared on c-Si substrate and vitreous silica substrate respectively. From the transmission spectra of $TiO_2$ films on vitreous silica substrate in the spectral region from 190 nm to 900 nm, k($\lambda$) of $TiO_2$ is obtained. Using k($\lambda$) in the interband transition region the coefficients of the quantum mechanical dispersion relation of an amorphous $TiO_2$ and hence n($\lambda$) including the optically opaque region of above fundamental transition energy are obtained. The spectroscopic ellipsometry spectra of $TiO_2$ films in the spectral region of 1.5-5.0eV are model analyzed to get the film packing density variation versus i) substrate material, ii) film thickness and iii) film growth technique. The complex refractive index change of these $TiO_2$ films versus water condensation is also studied. Film micro-structures by SE modelling results are compared with those by atomic force microscopy images and X-ray diffraction data.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.12
• /
• pp.814-818
• /
• 2016

DSSCs (dye-sensitized solar cells) based on $TiO_2/SiO_2$ multi layer AR (anti-reflection) coating on the outer glass FTO (fluorine-doped tin oxide) substrate are investigated. We have coated an AR layer on the surface of a DSSCs device by using an IAD (ion beam-assisted deposition) system and investigated the effects of the AR layer by measuring photovoltaic performance. Compared to the pure FTO substrate, the multi layer AR coating increased the total transmittance from 67.4 to 72.9% at 530 nm of wavelength. The main enhancement of solar conversion efficiency is attributed to the reduction of light reflection at the FTO substrate surface. This leads to the increase of Jsc and the efficiency improvement of DSSCs.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.766-772
• /
• 1996

Undoped $SnO_x$ thin films were deposited on Si(100) substrate by using reactive ioassisted deposition technique (R-IAD). In order to investigate the effect of initial oxygen content and heat treatment on the oxidation state and crystalline structure of tin oxide films, $SnO_x$ thin films were post-annealed at 400~$600^{\circ}C$ for 1 hr. in a vacuum ~$5 \times 10^{-3}$ -3/ Torr or were directly deposited on the substrate of $400^{\circ}C$ and the relative arrival ration ($Gamma$) of oxygen ion to Sn metal varied from 0.025 to 0.1, i.e., average impinging energy ($E_a$) form 25 to 100 eV/atom. As $E_a$ increased, the composition ratio of $N_ON{sn}$ changed from 1.25 to 1.93 in post-annealing, treatment and 1.21 to 1.87 in in-situ substrate heating. In case of post-annealing, the oxidation from SnO to $SnO_2$ was closely related to initial oxygen contents and post-annealing temperature, and the perfect oxidation of $SnO_2$ in the film was obtained at higher than $E_a$=75 eV/atom and $600^{\circ}C$. The temperature for perfect oxidation of $SnO_2$ was reduced as low as $400^{\circ}C$ through in-situ substrate heating. The variation of the chemical state of $SnO_x$ thin films with changing $E_a$'s and heating method were also observed by Auger electron spectroscopy.