• Journal of Convergence for Information Technology
• /
• v.8 no.2
• /
• pp.83-90
• /
• 2018

We have studied the optimal conditions for design and development on the communication device for a bilateral, and it's electrodes for transmitting electric signal are constructed on the $36^{\circ}$ rotated $LiTaO_3$ substrate by evaporating Al-Cu(W 30%) alloy. At first, we manufactured three kind of samples using this method, and selected two samples as similar with frequency, ripple and passband characteristics, and then we connect two samples by series in order to make bilateral devices. As results, we obtained that the electrode structure has better characteristics then the others, when it's width of reflector and electrode are $1{\lambda}/4$, $1{\lambda}/12$ respectively, and it's frequency is approximately 190.3MHz. Near future, I hope to help the manufacture for communication devices for the multi-channel and the duplex filter.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.433-440
• /
• 2014

In this study, a method for the low-carbon active distribution system (ADS) planning is proposed. It takes into account the impacts of both network capacity and demand correlation to the renewable energy accommodation, and incorporates demand response (DR) as an available resource in the ADS planning. The problem is formulated as a mixed integer nonlinear programming model, whereby the optimal allocation of renewable energy sources and the design of DR contract (i.e. payment incentives and default penalties) are determined simultaneously, in order to achieve the minimization of total cost and $CO_2$ emissions subjected to the system constraints. The uncertainties that involved are also considered by using the scenario synthesis method with the improved Taguchi's orthogonal array testing for reducing information redundancy. A novel cuckoo search (CS) is applied for the planning optimization. The case study results confirm the effectiveness and superiority of the proposed method.

• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2696-2707
• /
• 2021

The purpose of this study is to investigate the efficiency of various structural modeling schemes for evaluating seismic performances and fragility of the reactor containment building (RCB) structure in the advanced power reactor 1400 (APR1400) nuclear power plant (NPP). Four structural modeling schemes, i.e. lumped-mass stick model (LMSM), solid-based finite element model (Solid FEM), multi-layer shell model (MLSM), and beam-truss model (BTM), are developed to simulate the seismic behaviors of the containment structure. A full three-dimensional finite element model (full 3D FEM) is additionally constructed to verify the previous numerical models. A set of input ground motions with response spectra matching to the US NRC 1.60 design spectrum is generated to perform linear and nonlinear time-history analyses. Floor response spectra (FRS) and floor displacements are obtained at the different elevations of the structure since they are critical outputs for evaluating the seismic vulnerability of RCB and secondary components. The results show that the difference in seismic responses between linear and nonlinear analyses gets larger as an earthquake intensity increases. It is observed that the linear analysis underestimates floor displacements while it overestimates floor accelerations. Moreover, a systematic assessment of the capability and efficiency of each structural model is presented thoroughly. MLSM can be an alternative approach to a full 3D FEM, which is complicated in modeling and extremely time-consuming in dynamic analyses. Specifically, BTM is recommended as the optimal model for evaluating the nonlinear seismic performance of NPP structures. Thereafter, linear and nonlinear BTM are employed in a series of time-history analyses to develop fragility curves of RCB for different damage states. It is shown that the linear analysis underestimates the probability of damage of RCB at a given earthquake intensity when compared to the nonlinear analysis. The nonlinear analysis approach is highly suggested for assessing the vulnerability of NPP structures.

• Journal of the Korea Convergence Society
• /
• v.12 no.3
• /
• pp.141-149
• /
• 2021

3D printers, which emerged in the late 20th century, have become a key part of the fourth industrial revolution in the 21st century. Although 3D printers, the key equipment of the maker movement and the starting point of the new cottage industry in the 21st century, still reveal the limitations of mass production with low output speed and limited filament materials, the use of 3D printers by ceramic craftsmen has recently increased exponentially. However, as part of a way to overcome the discord between craftsmanship and the new technology, which has been repeated over and over in the past in craft history, the study focused on the 'plaster mold casting' technique using 3D printers. Therefore, after analyzing casting techniques of Tony Hansen, Webe van Gansbeck, Jade Crompton, and Ryu Hee-do, the potters who actively developed gypsum techniques in the world's ceramic crafts field and applied them to their own designs, I tried to find the point of convergence between 3D printers and ceramic crafts by presenting examples of effective 3D modeling methods and optimal slip casting methods using 3D printers.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.64 no.6
• /
• pp.43-53
• /
• 2022

Rice paddy has been actively converted into upland crop fields as more profitable upland crop cultivation are encouraged along with the decrease in rice consumption. However, the current water supply system remains mainly for paddy water supply, so research on pipeline water supply for upland cultivation is needed. The objective of this study was to optimize storage tank installation locations for pipeline water supply in reservoir irrigation districts. Five of reservoir irrigation districts were selected as the study sites and gridded of 10×10 m in size. Then genetic algorithm was adopted to evaluate the effects of spatial storage tank allocation on total pipeline cost. The lengths of the main and branch pipelines were considered as the objective cost function for the optimization of storage tank installation. Overall the shorter the branch pipeline and the longer the main pipeline, as the number of storage tanks increase. The minimal pipeline cost, i.e., optimal condition was reached when approximately 10% of the storage tank numbers to total upland plots were installed. The methodology presented in this study can be applied to determine the number and spatial arrangement of storage tanks for upland pipeline irrigation system design.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.4
• /
• pp.251-257
• /
• 2023

This study entailed an investigation of a tensile stress measurement method for prestressed concrete (PSC) tendons by utilizing external magnetization. The target of this study are PS structures that have been constructed and in use. An optimal external magnetization based elasto-magnetic (EM) sensor was designed using finite element analysis considering various factors, such as coil arrangement and size, that could influence the PS tendons inside the PSC girder. The residual tensile stress resulting from the external magnetization of the girder was then determined. Further, theoretical verification was performed using the numerical and material data used in the finite element analysis for sensor design. The calculated values of strength of magnetization at the target location were matched with the finite element analysis results. Thus, the designed sensor and the feasibility of magnetizing the tendons inside the PSC I-girder using an EM sensor were validated.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.41 no.6
• /
• pp.427-434
• /
• 2008

Processing of collagen from yellowfin tuna (Thunnus albacares) abdominal skins was optimized by response surface methodology and central composite design. The values of independent variables at optimal conditions were NaOH concentration: 0.5 N, NaOH treatment time: 36.2 hr, pepsin concentration: 1:4.9 ratio (0.245%, w/v), and digestion time: 48.1 hr, respectively. The collagen content estimated under optimal conditions was 33.1%, and the actual experimental collagen content was 32.3%. Physicochemical properties of collagen from yellowfin tuna abdominal skin were investigated by amino acids analysis, SDS-PAGE, FT-IR, viscosity and denaturation temperature. Amino acids content of the collagen was 21.0%. SDS-PAGE pattern of the collagen showed two different $\alpha$-chain (${\alpha}_1$- and ${\alpha}_2$- chain), $\beta$-component and $\gamma$-component. The spectrum of FT-IR of the collagen showed wavenumber at 3,434, 1,650, 1,542 and $1,235\;cm^{-1}$ representing the regions of amide A, I, II and III, respectively. Relative viscosity of the collagen decreased continuously on heating up to $32^{\circ}C$, and the rate of decrease was retarded in the temperature range of $35-50^{\circ}C$. Denaturation temperature (Td) of the collagen solution (0.06%, w/v) was $31^{\circ}C$ and was lower than calf skin collagen ($35^{\circ}C$).

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.12
• /
• pp.1731-1737
• /
• 2000

This study was conducted to investigate the effects of threonine:lysine ratios on growth performance, apparent nutrient digestibility and blood urea nitrogen (BUN) concentration, and to estimate the optimal threonine:lysine ratios for growing barrows and gilts. A total of 150 pigs (Landrace${\times}$Yorkshire${\times}$Duroc, $16.75{\pm}0.42kg$ average body weight, 75 barrows and 75 gilts) was randomly allotted into six treatments in a $2{\times}3$ factorial design. Six diets were formulated to contain 1.12% lysine for barrows and 1.33% lysine for gilts with three threonine:lysine ratios (50, 60 and 70%) for both barrows and gilts. Throughout the whole experimental period (16 to 56 kg body weight), there was no interaction between sex and dietary threonine:lysine ratio in average daily gain (ADG), average daily feed intake (ADFI) and feed conversion rate (FCR). Between sexes, there was a clear sex-effect showing better growth performance of barrows. Barrows consumed more feed (p<0.01) and grew faster (p<0.01) than gilts. For barrows, there was a trend to improved ADG and FCR with increasing threonine:lysine ratio. For gilts, there was a trend to improved ADG and FCR up to threonine:lysine ratio of 60%, but not significant. There was no interaction between sex and threonine:lysine ratio in nutrient digestibilities of growing pigs except for crude ash (CA). Between sexes, there were differences in nutrient digestibilities, except for calcium for which gilts showed higher a digestibility (p<0.01). Among dietary threonine:lysine ratios, there were no differences in nutrient digestibilities. Mean values of essential amino acids (EAA), non-essential amino acids (NEAA) and total amino acids (TAA) digestibilities were not affected by sex and dietary threonine:lysine ratio. There was no evidence of an interaction between sexes and dietary threonine:lysine ratio. Between sexes, total BUN concentration was lower in gilts than barrows (p<0.05). It was concluded that a 70 and 60% dietary threonine:lysine ratio for barrows (1.12% lysine) and gilts (1.33% lysine) tended to result in better growth performances and nutrient utilization and lower BUN concentration than other threonine:lysine ratios.

• Ecology and Resilient Infrastructure
• /
• v.3 no.2
• /
• pp.100-109
• /
• 2016

Low impact development (LID) facilities are established for the purpose of restoring the natural hydrologic cycle as well as the removal of pollutants from stormwater runoff. Improved efficiency of LID facilities can be obtained through the optimized interaction of their major components (i.e., plant, soil, filter media, microorganisms, etc.). Therefore, this study was performed to evaluate the performances of LID facilities in terms of runoff and pollutant reduction and also to provide an optimal maintenance method. The monitoring was conducted on four LID technologies (e.g., bioretention, small wetlands, rain garden and tree box filter). The optimal SA/CA (facility surface area / catchment area) ratio for runoff reduction greater than 40% is determined to be 1 - 5%. Since runoff reduction affects the pollutant removal efficiency in LID facilities, SA/CA ratio is derived as an important factor in designing LID facilities. The LID facilities that are found to be effective in reducing stormwater runoff are in the following order: rain garden > tree box filter > bioretention> small wetland. Meanwhile, in terms of removal of particulate matter (TSS), the effectiveness of the facilities are in the following order: rain garden > tree box filter > small wetland > bioretention; rain gardens > tree box filter > bioretention > small wetland were determined for the removal of organic matter (COD, TOC), nutrients (TN, TP) and heavy metals (Cu, Pb, Cd, Zn). These results can be used as an important material for the design of LID facilities in runoff volume and pollutant reduction.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.37 no.3_4
• /
• pp.34-47
• /
• 1995

It is experienced fact as a regular annual event that the structure to he designed on unreasonable flood for the agricultural structures including reservoirs have been brought not only loss of lives, but also enormous property damage. For the solution of this problem at issue, this study was conducted to develop an optimal runoff hydrograph model by comparison of the peak flows and time to peak between observed and simulated flows derived by linear time-invariant and linear time-variant models under the condition of having a short duration of heavy rainfall with uniform rainfall intensity at nine small watersheds which are within the range of 55.9 to 140.7 square kilometers in area in Han, Geum, Nagdong and Yeongsan Rivers. The results obtained through this study can be summarized as follows. 1. Storage constants and Gamma function arguments were calculated within the range of 1.2 to 6.42 and of 1.28 to 8.05 respectively by the moment method as the parameters for the analysis of runoff hydrograph based on linear time-invariant model. 2. Parameters for both linear time-invariant and linear time-variant models were calibrated with nine gaged watershed data, using a trial and error method. The resulting parameters including Gamma function argument, N and storage constant, K for linear time-invariant model were related statistically to watershed characteristic variables such as area, slope, length of main stream and the centroid length of the basin. 3. Average relative errors of the simulated peak discharge of calibrated runoff hydrographs by using linear time-variant and linear time-invariant models were shown to be 0.75 and 5.42 percent respectively to the peak of observed runoff hydrographs. Correlation coefficients for the statistical analysis in the same condition were shown to be 0.999 and 0.978 with a high significance respectively. Therefore, it can be concluded that the accuracy of a linear time-variant model is approaching more closely to the observed runoff hydrograph than that of a linear time-invariant model in the applied watersheds. 4. Average relative errors of the time to peak of calibrated runoff hydrographs by using linear time-variant and linear time-invariant models were shown to be 16.44 and 19.89 percent respectively to the time to peak of observed runoff hydrographs. Correlation coefficients in the same condition were also shown to be 0.999 and 0.886 with a high significance respectively. 5. It can be seen that the shape of simulated hydrograph based on a linear time- variant model is getting closer to the observed runoff hydrograph than that of a linear time-invariant model in the applied watersheds. 6. Two different models were verified with different rainfall-runoff events from data for the calibration by relative error and correlation analysis. Consequently, it can be generally concluded that verification results for the peak discharge and time to peak of simulated runoff hydrographs were in good agreement with those of calibrated runoff hydrographs.