• 소성∙가공
• /
• 제20권8호
• /
• pp.601-610
• /
• 2011

Based on the facts that AZ31 magnesium alloy can be blow formed just like superplastic aluminum alloys and that most superplastic alloys fail by cavitation, the present study was undertaken to investigate the cavitation behavior of a fine-grained AZ31 sheet during blow forming at the elevated temperature. Other points of interest included the much lower strain rate and temperature dependencies of the magnesium alloy compared with conventional superplastic alloys. It was also aimed to find if cavitation in the AZ31 alloy can be suppressed by hydrostatic pressure, as is the case in most superplastic alloys. Interestingly, the application of hydrostatic pressure did not increase the blow formability of AZ31 sheet, even though it reduced the degree of cavitation. A possible reason for this behavior is discussed.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.225-227
• /
• 2004

The compressive characteristics of thick carbon/epoxy composite in a submarine environment was investigated in this study. The specimens made of thick carbon fiber/epoxy composite that were immersed into seawater Jar thirteen months. the seawater content at saturation was about $1.2\%$ of the specimen weight. Compressive tests have been performed in different hydrostatic pressures of 0.1 MPa, 100 MPa, 200 MPa, and 270 MPa. The results showed that the compressive elastic modulus increased about $12.3\%$ as the hydrostatic pressure increased from 0.1 MPa to 200 MPa. The results also showed that compressive fracture strength increased $28\%$ and compressive fracture strain increased $8.5\%$ as the hydrostatic pressure increased from 0.1 MPa to 270 MPa.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.645-649
• /
• 1997

In case of swash plate type axial piston hydraulic motor, hydrostatic bearing used to achieve the lubrication effect on the mechanical sliding contact areas between the following parirs ; sliooer-pad and swash plate,piston and cylinder bore,valve plate and cylinder block, etc. This study discussed the basic charateristic for the hydrostatic slipper-pad bearings with the capillary or orifice restrictor under static load condition. And, we also development of hydrostatic bearing tester for hydrostatic balancing test of pistion & slipper-pad assembly, and some experimental data on supply pressure step responce are reported.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.5-9
• /
• 2011

The hydraulic piston using a hydrostatic bearing has been used widely due to its satisfying performance at very high pressurized circumstance and relative higher power density in comparison to conventional one. For high pressurization, enhanced efficiency and long durability of the hydraulic piston, the design of hydrostatic bearing is at issue, which is installed between piston shoe and swash plate. The performance of the hydrostatic bearing is influenced significantly by the assembly of the piston shoe consisting of circular land and recess. In this study, to estimate the performance of the hydrostatic bearing, the characteristics for lubrication of the assembly of the piston shoe were investigated by measuring a leakage rate of hydraulic fluid under an experimental condition, where a rotating velocity of the piston, hydraulic pressure and temperature of the hydraulic fluid were changed systematically. In addition, a film thickness of the hydraulic fluid on the piston shoe was measured and compared to theoretical one.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.39-44
• /
• 2009

The hydrostatic slipper bearing is generally used in high pressure axial piston pumps to support the load generated from two surfaces which are sliding relatively at low speed. The object of the bearing is to remove the possibility of direct contact by maintenance of an adequate oil film thickness between two metal surfaces. Because the bearing performance is influenced by the bearing deformation, it is highly dependent on the injection pressure, the bearing surface profile and so on. In this study, the deformation characteristics of a hydrostatic slipper bearing is investigated according to the injection pressure by the finite element analysis. In the analysis, the special boundary condition to take the fluid-structure interaction (FSI) into account is used on the interactive surface. The results, such as bearing deformation, stress and lifting force, obtained from the fully coupled analysis are compared with those from the single step sequential method.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.117-123
• /
• 2003

This paper deals with pressure ripple and noise reduction characteristics for a hydrostatic transmission(HST) consisting of a variable axial piston pump connected in an open loop to a fixed displacement axial piston motor. Pressure ripples in HST is major source of vibration, which can lead to fatigue failure of components and cause noise. In order to reduce the pressure ripple, an annular tube type hydraulic filter proposes to absorb pressure ripples with the high frequencies components to achieve better noise attenuation in HST. The basic principle tube is applied to propagation of pressure wave, reflection, absorption in cross section of discontinuity and resonance in the hydraulic pipeline. It is experimently confirmed that a hydraulic filter is absorbed to be about 30∼40dB of pressure ripple with high frequencies. These results will assist in modeling and design of noise reduction in hydraulic control systems, and here, should provide a means of designing a quieter HST.

• 한국식품과학회지
• /
• 제30권3호
• /
• pp.596-601
• /
• 1998

비열처리공법 중 하나로 새롭게 주목받고 있는 초고압 처리를 동치미에 적용하여 미생물의 살균정도, 효소 활성과 hardness의 변화를 관찰하였다. 제조한 동치미를 $30^{\circ}C$ 배양기에서 발효 적숙기라고 판단되는 pH 4.0까지 발효시킨 후, 이를 시료로 사용하여 $200{\sim}686\;MPa$ 범위의 압력에서 5분간 처리하였다. 무처리군의 균체수는 호기성 세균, 젖산균, 효모 및 곰팡이가 각각 $4.05{\times}10^8,\;3.25{\times}10^8,\;3.55{\times}10^4\;CFU/mL$ 존재하였으나, 호기성 세균은 600 MPa, 젖산균과 효모 및 곰팡이는 400 MPa 이상에서 완전히 살균되었다. 젖산균의 압력에 따른 내압성을 관찰해 본 결과 380 MPa에서 Leuconostoc mesenteroides가 유일하게 검출되어 가장 강한 내압성을 나타내었으며, 김치의 주 산패균으로 알려진 Lactobacillus plantarum은 300 MPa로 처리한 시료에서도 발견되지 않아 압력에 약한 균주로 판단되었다. 조직감에 관계하는 효소인 pectinesterase (PE)와 polygalacturonase (PG)는 압력에 의해 모두 활성이 증가하였다. 초고압 처리를 하지 않은 시료의 효소 활성을 100으로 했을 때, PE는 500 MPa에서 193으로 가장 활성이 높았으며, PG는 압력이 증가함에 따라 활성이 서서히 증가하여 686 MPa에서 191이었다. 동치미에 있는 무의 조직감은 초고압 처리했을 때 hardness가 증가하여 400 MPa에서 5분간 처리한 시료는 무처리군에 비해 약 0.065kg이 높았다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.377-380
• /
• 2000

The collapsible phenomena of the circular tubes due to the excessive transmural pressure are investigated experimentally. Collapsible tubes are installed in the test section where the external pressure is applied to the test tubes by applying the hydrostatic head. The collapsible circular tubes are made of rubber, whose diameters are 6 and 4.2 mm, respectively. The hydrostatic water head of the upper reservoir is applied to the test section. Pressures at the upstream and downstream sides are measured by the pressure transducers. The collapsible phenomena are observed as the transmural pressure Increases, and also the flutter phenomenon occurs due to the critical transmural pressure.

• 한국해양공학회지
• /
• 제21권3호
• /
• pp.52-57
• /
• 2007

Composite material is one of the strongest candidates for deep see pressure hulls. Research regarding composite cylinders, subjected to hydrostatic pressure, has been ongoing for a couple of decades, abroad, but domestic research is very new. Experimental investigations seem necessary, in order to understand their structural behavior not only up to the ultimate limit state, but in the post-ultimate regime. That experimental information will be very helpful in the development of any theoretical methods or to substantiate any commercial numerical packages for structural analyses. In this study, ultimate strength tests on seven composite cylinders subjected to hydrostatic pressure are reported, which includes the fabrication method of models, mechanical properties of the material, initial shape imperfection measurements, test procedure, and strain and axial shortening measurements during the tests. The ultimate strengths of the models were compared with predictions of numerical analyses. The numerical predictions are higher than the test results. It seems necessary to improve the accuracy of the numerical predictions by considering the initial shape and material imperfections.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.154-157
• /
• 2006

Composite material is one of the strong candidates for deep see pressure hulls. Research regarding composite unstiffened or stiffened cylinders subjected to hydrostatic pressure has a couple of decades history abroad but domestic research is very new. Experimental investigations seem necessary to understand their structural behavior not only up to the ultimate limit state but in post-ultimate regime. Those experimental information will be very helpful to develop any theoretical methods or to substantiate any commercial numerical packages for structural analyses. In this study, ultimate strength tests on seven composite cylinders subjected to hydrostatic pressure are reported, which includes the fabrication method of models, material properties of the material, initial shape imperfection measurements, test procedure and strain and axial shortening measurements during the tests. The ultimate strengths of the models were compared with those of numerical analyses. The numerical predictions are higher than the test results. It is necessary to improve the accuracy of the numerical predictions.