• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.4
• /
• pp.552-559
• /
• 2015

Hydrogen is commonly used in many industrial field. However, hydrogen should be filled in a high pressure container to use it. Therefore, many researches have been conducted about an electrolyzer. The operating principle of the electrolyzer is that the electrolyzer can separate water molecules into hydrogen and oxygen. To use the electrolyzer, a power conversion system is needed because the current of the electrolyzer increases exponentially depending on the voltage of the electrolyzer. Thus, this paper proposes the power conversion system for the electrolyzer using a full-bridge DC-DC converter topology.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1132_1133
• /
• 2009

In this paper, a observer-based PI controller will be developed for PEM fuel cell system. Nonlinear model of PEM fuel cell system is introduced to study the controller design problems. Sliding mode observer will be designed to estimate the cathode and anode pressures of PEMFC system. And a nonlinear state observer is also designed to estimate the other states such as supply manifold pressure, Oxygen pressure, Hydrogen pressure, return manifold pressure, etc. These estimated states are used to design the observer-based PI controller. The validity of the proposed controller will be verified by using computer simulation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.1
• /
• pp.19-26
• /
• 1999

The effectiveness of a double-tube heat exchanger has been investigated experimentally. This problem is of particular interest in the design of the heat exchanger in a hydrogen liquefaction system. Temperature, pressure, and mass flow rate for hydrogen were measured both in inner tube and in annulus of a double-tube heat exchanger. The effectiveness could be evaluated from the measured temperature and mass flow rate. It is found that the effectiveness increases with an increase in the heat transfer area of a double-tube heat exchanger and with a decrease of the heat capacity ratio. But the increase rate of the effectiveness decreased with a decrease of the heat capacity ratio. Therefore, it is presented that a criterion for selecting the heat exchanger length and heat capacity ratio to obtain the effectiveness required in a hydrogen liquefaction system.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.67-70
• /
• 2009

Because many research using rocket grade peroxide is studied, distillation method for domestic production of rocket grade hydrogen peroxide is required. Distillation methods are very various and divided by feeding method, distillation time, distillation pressure, and so on. Among these, vacuum distillation is a suitable method for hydrogen peroxide. This method can reduce thermal decomposition and reaction with impurities. Distillation condition is determined by Raoult's law. Low vacuum level and vacuum level control are appeared as important problems of the experiment equipment, which are solved by using less leakage vacuum chamber and metering valve.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.5
• /
• pp.625-633
• /
• 2011

Characteristics of a commercial metal hydride (MH) hydrogen supply system have been investigated and an operating strategy was developed based on the experimental data. As a prior step, charging/discharging capacity, thermal properties such as heat capacity, heat of reaction of MH system were experimentally measured. And then P-C-T data for various operating conditions were collected and a correlation between P, C and T predicting the behavior of MH was derived. Based on the basic experimental data, an operating strategy of MH system was developed, in which the hot water temperature supplied into the water jacket of MH was controlled depending on the pressure of MH, thereby the pressure of MH could be maintained at a suitable range. By adjusting the temperature of hot water from $40^{\circ}C$ to $60^{\circ}C$, the maximum discharging capacity of hydrogen could be increased by 4.7%, and consequently more stable hydrogen supply and longer operation time of fuel cell system could be achieved.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.205-211
• /
• 2021

Recently, it is necessary for study on renewable energy due to environmental pollution and fossil fuel depletion. Therefore, in this study, the filling temperature according to the nozzle geometry was evaluated based on the limit temperature specified in SAEJ2601 for charging hydrogen, a new energy. There are three types of nozzles, normal, angle and round, fixed the average pressure ramp rate at 52.5 MPa/min, and the injection temperature was set at 293.4 K. As a result, the lowest temperature distribution was found in the round type, although the final temperature did not differ significantly in the three types of nozzles. In addition, Pearson's coefficient was calculated to correlate the mass flow rate with the heat transfer rate at the inner liner wall, which resulted in a strong linear relationship of 0.98 or higher.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.5
• /
• pp.456-464
• /
• 2023

In this study, a compact hydrogen liquefaction system was constructed with the aim of creating a data storage and monitoring program for liquid hydrogen production. This program was designed to receive and record signals from diverse control equipment through the LabVIEW software. A range of measurement instruments were devised to collect data, encompassing variables such as flow rate, pressure, temperature, and liquid level. As a result, it was possible to directly check the production of liquid hydrogen by obtaining various data of condensed liquid hydrogen. In addition, it was confirmed that long-term storage of liquid hydrogen is possible by developing automatic ON/OFF through the LabVIEW program.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.284-284
• /
• 2010

Currently, hydrogen has been produced by Steam Reforming or partial oxidation reforming processes mainly from oil, coal, and natural gas and results in the production of $CO_2$. However, these are influenced greatly on the green house effect of the earth. so it is important to find the new way to produce hydrogen utilizing water without producing any environmentally harmful by-products. In our research, we use microwave water plasma and photocatalyst to improve dissociation rate of water. At low pressure plasma, electron have high energy but density is low, so temperature of reactor is low. This may cause of recombination in the generated hydrogen and oxygen from splitting water. If it want to high dissociation rate of water, it is necessary to control of recombination of the hydrogen and oxygen using photocatalyst. We utilize the photocatalytic material($TiO_2$, ZnO) coated plasma reactor to use UV in the plasma. The quantity of hydrogen generated was measured by a Residual Gas Analyzer.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06b
• /
• pp.87-107
• /
• 1996

The fine Co powder with an average particle sie of less than 1$\mu\textrm{m}$ was prepared by hydrothermal reduction with hydrogen from Co(OH)2 slurry obtained by mixing the solutons of CoSO4$.$7H2O and NaOH. A method to control pH of the end solution around neutrality was proposed. The reduction rate was found to be a function of pH, temperature, hydrogen pressure and the amount of catalyst.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.513-516
• /
• 1987

Hydrogenated amorphous silicon (a-Si:H) films have been deposited, for thye first time, by a remote plasma chemical vapor deposition. The hydrogen radical play a important role to control the deposition rate, The bonded hydrogen content to silicon is independent of hydrogen partial pressure in the plasma. Optical gap of deposited a-Si:H lies between 1.7eV and 1.8eV and all samples have sharp absorption edge. B-doped a-Si:H films by a RPECVD has a high doping efficiency compared with plasma CVD. The Fermi level of 100ppm B-doped film lies at 0.5eV above valence band edge.