• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.67-71
• /
• 2013

$FeCl_3$ has been used as an etchant for metal etching such as Fe, Cu, and Al. In the process of metal etching, $Fe^{3+}$ is reducted to $Fe^{2+}$ and the etching rate becomes slow and etching efficiency decreased. Waste $FeCl_3$ etchant needs to be regenerated because of its toxicity and treatment cost. In this work, HCl was initially mixed with the waste $FeCl_3$ and then, strong oxidants, such as $O_2$ and $H_2O_2$, were added into the mixed solution to regenerate the waste etchant. During successive etching and regeneration processes, oxygen-reduction potential (ORP) was continuously measured and the relationship between ORP and etching capability was investigated. Regenerated etchant using a two vol% HCl of the total etchant volume and a very small amount of $H_2O_2$ was very effective in recovering etching capability. During the etching-regeneration process, the same oxygen-reduction potential variation cannot be repeated every cycle since concentrations of $Fe^{2+}$ and $Fe^{3+}$ ions were continuously changed. It suggested that the control of etching-regeneration process based on the etching time becomes more efficient than that of the process based on oxygen reduction potential changes.

• Journal of fish pathology
• /
• v.25 no.2
• /
• pp.123-126
• /
• 2012

Exfoliation of fouling abalone, Haliotis discus hannai from shelters by commercial oxytetracycline (OTC) was observed in culture farms. In the present study, different components of OTC for exfoliation of abalone were investigated to understand how to work. Abalone were detached from shelter in 14,000 ppm of commercial OTC (main ingredients of OTC: OTC-hydrogen chloride (HCl), 50%; glucose, 49%; blue pigment, <1%), but not below 8,000 ppm. A 95% of exfoliation rate was observed in OTC-HCl (7,000 ppm, pH 2.8) but no exfoliation in OTC-HCl (7,000 ppm, pH 5.0), glucose (7,000 ppm) or blue pigment (140 ppm). Moreover 100% exfoliation rate was observed in HCl-seawater of pH 2.8. These results indicate that HCl is the component resulting in exfoliation of the fouling abalone. Abalone was detached in HCl solution (pH 2.5-3.2) within 2 min. However, a lower pH and longer treatment resulted in delayed recovery of the detached abalone. Thus, exfoliation of fouling abalone can be achieved by a low pH treatment with cautious handling.

• Journal of Wetlands Research
• /
• v.25 no.4
• /
• pp.291-296
• /
• 2023

DIWS system was employed to treat hydrochloric acid gas from cold rolling mill process of iron and steel industry. Chlorine gas generated from the acid regeneration system was combined with hydrogen gas and hydrogen chloride gas was increased to 50%. After the injection of Na₂S₂O₃ to remove chlorine gas, the removal of hydrogen chloride was stably kept 87.5~88.8%, where the inflow was 13.1~13.4ppm and the outflow was 1.5~1.7ppm. DIWS system can be recommended for the real iron and steel plant because it was stably maintained not only the air emission standards but also the reduction of chemical usage.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.2
• /
• pp.103-108
• /
• 2014

Using dried sludge as a secondary fuel of a coal-fired power plant is proposed as an alternative option for sludge disposal. Because elemental contents of sludge are different from those of coal, different levels of acidic gas emissions are expected from the co-combustion of sludge with coal. In this study, sludge samples were obtained from 7 sewage treatment plants in Korea. Each sludge sample was combusted together with coal in a lab-scale combustor, and the concentrations of nitrogen oxides ($NO_x$), sulfur dioxide ($SO_2$), hydrogen chloride (HCl), chlorine ($Cl_2$) in the flue gas were analyzed. Compared to the combustion of coal only, $NO_x$ concentration was slightly higher in the flue gas from the co-combustion of coal and sludge. $SO_2$ emission increased with the combustion of sludge due to the higher content of sulfur in sludge than in coal. For most of the tested samples, the concentrations of HCl and $Cl_2$ were varied depending on the chlorine content in the sludge sample.

• Bulletin of the Korean Chemical Society
• /
• v.12 no.4
• /
• pp.371-373
• /
• 1991

The crystal structure of eprazinone dihydrochloride, $C_{24}H_{32}N_2O_2$${\cdot}$2HCl, has been determined from 2102 independent reflections collected on an automated Nonious CAD-4 diffractometer using graphite-monochromated $Mo-K\alpha$ radiation. The crystals are monoclinic, space group P$2_1$/n, with unit cell dimensions a=11.381(2), b=28.318(2), c=7.840(1) $\AA$, $\beta=92.45(2)^{\circ}$, ${\mu}=2.37$ c$m^{-1}$, F(000)=968, and Z=4. Final R value is 0.071 for independent 2102 observed reflections. The molecule assumes an extended conformation. The piperazine ring has a normal chair conformation and the four carbon atom are planar with a maximum displacement of 0.004 $\AA$ for C(18) atom. The two chloride ions are hydrogen bonded to the two piperazine nitrogen atoms [N(14)${\cdot}{\cdot}{\cdot}$Cl(1); 2.986(6) $\AA$ N(17)…Cl(2); 3.084(8) $\AA$].

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.10
• /
• pp.1594-1598
• /
• 2015

This study was performed to investigate the effects of various acidic treatment for anthocyanin and proanthocyanidin extraction from black bean. Extracts were prepared with 80% methanol solutions containing HCl, acetic, formic, phosphoric, and citric acids of different concentrations (0.1, 0.2, 0.3, 0.5, and 0.7%). Total anthocyanin content ranged from 0.74 mg/g in 0.7% citric acid to 1.74 mg/g in 0.3% HCl, depending on acid type and concentration. The major anthocyanins were delphinidin-3-glucoside (D3G), cyanidin-3-glucoside (C3G), and petunidin-3-glucoside (Pt3G). The highest C3G content was 1.12 mg/g in 0.3% HCl. Proanthocyanidin content ranged from 2.01 mg/g in 0.5% acetic acid to 5.29 mg/g in 0.3% HCl. Thus, acidic condition is a significant factor affecting anthocyanin and proanthocyanidin extraction from black bean, and the optimum extraction conditions were determined as 80% methanol containing 0.3% HCl.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.7-12
• /
• 1984

In this paper, the authors applied the method of hydrogen chloride gettering oxidation to fabricate the low noise bipolar transistor. The results of measurements of the effect of guttering on the variation of flicker noise spectral intensity for variable HCI concentrations indicate that flicker noise in bipolar than-sistor is dependent on the surface condition and that the gettering in a mixture of 2% HCI in oxidation produced the optimal results in the fabrication of the low noise device. In addition, it was also noted that the PSG layer formed by the emitter source (phosphorus) did not have so much guttering effect as in the process with HCl getterinng.

• Journal of the Korean Chemical Society
• /
• v.7 no.2
• /
• pp.186-188
• /
• 1963

An attempt to improve the method of volumetric determination of tungsten developed by Luke has been made successfully. Using amalgam coated lead instead of pure metallic lead in the reduction procedure. W(VI)-W(III) reduction has been found to be quantitative in rather concentrated hydrochloric acid. Since there was no excessive dissolution of lead via reduction of hydrogen ion, lead surface was totally accessible for the reduction of tungsten and no trouble was caused by dereposition of $PbCl_2$ crystals at the nozzle of Jones reductor. Furthermore, it has been confirmed that almost 100 mg. of $WO_3$ can be handled easily if the chloride concentration of the HCl is increased by adding solid $NH_4Cl$.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.09a
• /
• pp.103-111
• /
• 1998

Au fine particle dispersed TiO2 film was prepared on silica glass substrate by sol-gel dip and firing process. The films were fabricated from the system of titanium tetraisoproxie-EtOh-HCl_H2O-hydrogen tetrachloroaurate(III) tetrahydrate. The conditions for the formation of the clear solution and dissolving high concentration of Au compound were examined. And a photoreduction process was adopted to control the size of gold metal particles. Phase evolution of matrix TiO2 and variation of Au particle with UV irradiation were investigated by XRDA, SEM, TEM and UV-visible spectrophotometer. And the effect of CPCl(Cetylpyridinium chloride monohydrate) as a dispersion agent was evaluated.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.12
• /
• pp.1269-1273
• /
• 1997

The system which employs iron, palladium, molecular oxygen and hydrogen as a model mono-oxygenase, has been investigated to develop a new method for selective cyclohexane oxidation uner mild conditions. This system provides much higher yield and selectivity for the formation of cyclohexanol and cyclohexanone compared to that of the existing industrial method. When the catalytic system, FeCl2-Pd/alumina, was employed, the oxidation system required acetone as a solvent to be efficient and acidifying the solvent by a little addition of acetic acid or HCl made the system more efficient. The Pd catalyst was recyclable without a significant deactivation but the recycling of ferrous chloride showed the decrease in the activity. On the other hand, the heterogeneous catalytic system, Pd/Fe2O3 could be recovered easily and reused after drying treatment.