• Tribology and Lubricants
• /
• 제33권2호
• /
• pp.71-78
• /
• 2017

The drag torque in the wet clutch system of a dual clutch transmission system is investigated because it is relatively high, up to 10 of the total output torque of the engine, even when the clutch is in the disengagement state with zero torque transfer. Drag torque results from the shear resistance of the DCTF between the friction pad and separator plate. To reduce the drag torque for ensuring fuel economy, the groove pattern of the wet clutch friction pad is designed to have a high flow rate through the pattern groove. In this study, four types of groove patterns on the friction pad are designed. The volume fraction of the DCTF (VOF) and hydrodynamic pressure developments in the gap between the friction pad and separator plate are computed to correlate with the computation of the drag torque. From the computational results, it is found that a high VOF and hydrodynamics increase the drag torque resulting from the shear resistance of the DCTF. Therefore, a patterned groove design should be used for increasing the flow rate to have more air parts in the gap to reduce the drag torque. In this study, ANSYS FLUENT is used to solve the flow analysis.

• Corrosion Science and Technology
• /
• 제7권5호
• /
• pp.283-287
• /
• 2008

The drag reduction agency (DRA) for gas pipeline, a novel method used for reducing friction or drag on a gas flowing to increase the transmission efficiency of gas pipeline, is a more flexible and economical technology than internal flow efficient coatings. In this paper, an effective DRA has been developed in Authors' Institute by analyzing the hydrodynamic friction resistance on internal gas pipeline and then studying the work mechanism and molecular structure of DRA. In the meantime, a group of property test for selecting DRA material has been determined, including viscosity, contact angle, volatility, corrosion, slab extending, and flow behavior in horizontal tube. The inhibition efficiency and drag reduction efficiency of the developed DRA have been investigated finally based on the relevant test methods. Results of corrosion test show that the developed DRA has very good inhibition effect on mild steel by brushing a thin layer of DRA on steel specimens, giving inhibition efficiency of 91.2% and 73.1% in 3%NaCl solution and standard salt fog environment respectively. Results of drag-reducing test also show that the Colebrook formula could be used to calculate friction factors on internal pipes with DRA as the Reynolds number is in the range of $0.75\times10^5\sim2.0\times10^5$. By comparing with normal industrial pipes, the friction resistance coefficient of the steel pipe with DRA on internal wall decreases by 13% and the gas flux increases by 7.3% in testing condition with Reynolds number of $2.0\times10^5$.

• 한국해안·해양공학회논문집
• /
• 제30권3호
• /
• pp.114-122
• /
• 2018

본 연구는 다공성 구조물과의 파랑의 상호 작용을 수치모의하기 위한 비정수압 수치모형인 SWASH를 소개한다. 이 수치모형은 ${\sigma}$-좌표계에 Volume Averaged Reynolds Averaged Navier-Stokes(VARANS)을 지배방정식으로 다공성 매체에서의 유동을 계산한다. 다공성 매체에서의 유동을 고려하기 위해 사용된 경험적 저항 계수는 보정 작업이 필요하다. 본 연구에서는 수치모형에 사용된 경험적 저항 계수를 다공성 매체를 통과하는 댐 붕괴 실험과 다공성 구조물과 고립파의 상호 작용에 대한 실험을 이용하여 보정 및 검증하였다. 실험 결과와 수치실험 결과는 비교적 잘 일치하는 것으로 나타났다. 또한 비정수압 수치모형인 SWASH가 VOF 접근법을 기반으로 하는 3차원 다공성 유동 모델보다 계산상 훨씬 더 효율적이라는 것이 확인되었다.

• 동력기계공학회지
• /
• 제21권3호
• /
• pp.51-59
• /
• 2017

In the early design stage of underwater vehicles, it is important to estimate the vehicle's underwater motion performance. The key design elements for the motion are propellers, battery power, and underwater resistance of the vehicle. Small thrusters with motor and propeller are usually used for the UUV(unmanned underwater vehicles). In this study, a multiphysics thruster model combining electro-mechanical and hydrodynamics characteristics was proposed to estimate the thruster performance. To show the applicability of the mathematical model, an sample thruster was used for the derive the unknown parameters of thruster. Hydrodynamic parameters were calculated for a 3D geometry model of the propeller by ANSYS/CFX program. Finally, Matlab/simulink program was used for the numerical simulation to predict the thruster performance from the given voltage/current input to the motor. Also, proved validity of simulation model by experiment test. Test were done by 2 mode(middle/high speed, reverse). The thruster performance curves obtained from this simulation were confirmed to be similar with experiment results.

• 한국해양공학회지
• /
• 제25권6호
• /
• pp.17-22
• /
• 2011

This study conducted wide-tank experiments and numerical calculations for a vessel in various positions such as upright and inclined by 2 and 4 degrees, with the goal of investigating the motion amplitude response of a small damaged fishing boat subject to a beam sea. Numerical calculations were conducted based on the three-dimensional source distribution method. The good agreement of the numerical calculation and experimental results confirmed that the present calculation method can be efficiently used for the initial design of a small fishing boat. In addition, while the chine-line type has been frequently adopted to improve a ship's resistance performance in the design of a small fishing boat, it is considered that the possibility of a deterioration in rolling performance should be thoroughly considered.

• 수산해양기술연구
• /
• 제38권2호
• /
• pp.172-178
• /
• 2002

본 연구는 유체역학적 해석을 이용하여 선망 어구 운동을 동적으로 시뮬레이션하였다. 선망 어구는 조업 과정 중에 어구의 형상이 크게 바뀌는 특성이 있고, 모든 조업단계에서 어구요소가 3차 시스템이며 대부분 망지라는 유연한 물체에 의해 구성되어 있어 외력에 대해 그 형상이 비선형적으로 변하므로 모델링이 어렵다. 본 연구에서는 질량-스프링 모델을 이용하여 수학적으로 기술하였다. 선망의 조업 과정중 그물의 투망, 침강, 죔줄을 죄는 과정의 어구운동을 시뮬레이션하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.720-723
• /
• 2005

Ship motion is a complex controlled process with several hydrodynamic parameters that vary in wide ranges with respect to ship load condition, speed and surrounding conditions (such as wind, current, tide, etc.). Therefore, to effectively control ships in a designed track is always an important task for ship masters. This paper presents an effective adaptive autopilot ships that ensure the optimal accuracy, economy and stability characteristics. The PID control methodology is modified and parameters of a PID controller is designed to satisfy conditions for an optimal objective function that comprised by heading error, resistance and drift during changing course, and loss of surge velocity or fuel consumption. Designing of the controller for course changing process is based on the Model Reference Adaptive System (MRAS) control theory, while as designing of the automatic course keeping process is based on the Self Tuning Regulator (STR) control theory. Simulation (using MATLAB software) in various disturbance conditions shows that in comparison with conventional PID autopilots, the designed autopilot has several notable advantages: higher course turning speed, lower swing of ship bow even in strong waves and winds, high accuracy of course keeping, shorter time of rudder actions smaller times of changing rudder direction.

• Elastomers and Composites
• /
• 제34권4호
• /
• pp.315-320
• /
• 1999

점착성과 소수성을 제거함으로써 실리콘 EVD 튜브의 성능을 향상시키기 위하여 저온 플라스마 공정을 이용한 실리콘 고무의 표면개질을 시도하였다. 고분자를 형성하지 않는 플라스마를 이용한 표면처리와 고분자를 형성하는 플라스마를 이용한 박막코팅 방법을 시도하였다. 박막코팅을 할 경우에 점착성이 특히 크게 줄어들었으며, 결과적으로 실험실 환경에서의 오염 정도를 줄일 수 있었다. 산소를 포함한 플라스마를 이응할 경우 튜브의 외부뿐만 아니라 내부의 표면을 친수성으로 개질시킴으로써, 결과적으로 수력학적 초기 저항을 줄일 수 있었다. 대부분의 경우에 있어서, 이러한 표면개질은 실리콘 튜브의 기계적 물성에 아무런 악영향을 끼치지 않았으며 영율, 인장강도, 인장율 등의 물성은 오히려 향상되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권8호
• /
• pp.1094-1099
• /
• 2010

수중에 있는 구 주위의 3차원 층류유동을 수치 해석하였다. 유한체적법을 기반으로 나비에 스톡스 방정식을 비구조격자로 풀어 물체주위의 동역학 현상을 규명하였다. 보티시티, 속도, 동압, 레지듀얼, 항력계수 등의 데이터를 가지고 분석하였다. 레이놀드 수는 425, 300, 250, 100 이다. 구 사이의 거리가 작은 경우가 구 한 개의 후류 유동보다 안정됨을 보였고 구 사이의 간격이 커짐에 따라 유동현상은 불안정하게 나타났다. 후방의 구는 정체압력의 감소를 보였고 이로 인해 저항이 줄어들게 됨을 알 수 있었다. 항력계수의 비교는 본 수치계산이 타당함을 입증하였다.

• 열처리공학회지
• /
• 제9권3호
• /
• pp.169-176
• /
• 1996

Effect of retained austenite on rolling contact fatigue of nitrocarburized high-carbon chromium bearing steel has been investigated to develop surface-hardened bearing steel with imprved resistance to rolling contact fatigue. Fatigue tests were conducted in elesto-hydrodynamic lubricating conditions at a shaft speed of 5,000rpm, under max, hertzian stress of $492kg/mm^2$. Volume fraction of retained austenite in austenitic nitrocarburized STB2 steel was controlled by tempering at various temperature, $200{\sim}250^{\circ}C$. It was observed using TEM that decomposition of retained austenite during tempering at $250^{\circ}C$ was the highest in quantity, resulted in formation of lower bainite. Rolling contact fatigue life of the specimens with lower bainite, formed by decomposition of retained austenite, was improved in comparison with there of specimens with more amount of retained austenite.