• 멤브레인
• /
• 제27권6호
• /
• pp.519-527
• /
• 2017

멤브레인 파울링은 지표수를 처리하는 저압 멤브레인 기술 적용의 확장에 있어 큰 장애가 된다. 따라서 파울링 제어를 위한 주기적인 수리학적 세정기술의 최적화는 매우 중요하다. 주기적인 수리학적 세정과 이와 연관된 파울링 현상에 관한 올바른 이해는 멤브레인 세정 전략을 최적화하기 위해 매우 유용할 수 있다. 실험적으로 측정한 투과도와 전통적인 Hermia 파울링 모델 예측 치의 비교를 통해, 본 연구에서는 합성 탁도유발 시료를 처리하는 가압식 멤브레인 공정에서 30분 여과와 정세정/역세정이 포함된 1분 세정조건을 바탕으로 6번의 운전사이클을 통해 발생하는 파울링 현상을 분석하고 이를 통해 지배적인 파울링 기작을 정량적으로 이해하고자 하였다. 단독 세정에서, 첫 번째 운전사이클에서 발생하는 파울링은 완전공극막힘 현상에 의해 주로 지배되었고 마지막 운전 사이클에서는 케이크 형성이 지배적인 파울링 기작으로 관찰되었다. 정세정과 역세정이 혼합된 경우, 파울링 속도는 감소하였으나 전반적으로 케이크 형성이 주 파울링 기작으로 관찰되었다.

• 한국농공학회논문집
• /
• 제56권5호
• /
• pp.67-75
• /
• 2014

In this study, the large-scale hydraulic model test was performed to investigate the hydraulic characteristics for development of the non-power soil cleaning and keeping system at the dike gate. The outlet height, outflow number, outflow discharge, and outflow cycle were compared and analyzed. The non-power soil cleaning and keeping system was most effective at 11.2 mm in the outlet height. And then the mean outflow cycle was 1.09 sec, and the mean outflow discharge was $0.00164m^3/s$. The total outflow number increased gradually as the water level of a water tank increased, and the outlet height decreased. As a level of water tank decreased, the mean outflow cycle was lengthened, and the unit outflow discharge increased. This result showed this system was most effective. To remove the silty clay deposited in facilities, the methods of excavation, dredging, high pressure washing, etc have been applied to the tidal facilities such as land reclamation, a small size fishing port, and a harbor for maintenance. However, this is extremely cost-ineffective, whereas the non-power soil cleaning and keeping system will bring about an enormously positive economic effect. In addition, when the non-power soil cleaning and keeping system is applied to the dike gate of land reclamation, a thorough examination of the local tidal data and the careful system planning are required to prevent the disaster damage caused by flooding.

• 한국물환경학회지
• /
• 제18권3호
• /
• pp.303-312
• /
• 2002

본 연구에서는 기존 배관설비 분야에서 다양한 용도로 사용되고 있는 Polly-Pigs를 이용한 건물내 급수관의 스케일을 제거하기 위한 공법을 개발하여 이를 평가하였다. 15mm 노후관의 세관실험결과, KDP series에 의해서 직관부 또는 곡관부의 통수능은 3.5~15.4%까지 증가되는 것으로 나타났으며, 육안분석결과 대부분 제거가 이루어진 부분은 적색 스케일($Fe_2O_3{\cdot}3H_2O$)이었으며, 흑색 스케일($Fe_2O_4{\cdot}nH_2O$)의 제거에는 한계가 있는 것으로 나타났다. 그러나 KDP series의 겉표면에서 Fine sand를 coating한 KDPS series에 의해서는 sand의 효과로 노후관의 통수능이 13.0~17.9%까지 증가되어 통수능이 95.9~99.5%까지 높게 회복되는 것으로 나타났으며, 대부분의 흑색 스케일도 크게 제거되는 것으로 나타났다. 또한 Cleaning v/v의 나선형 가이드 베인(Helical guide vane)과 Pigs의 회전날개(Rotating wing)의 영향으로 주행시 Pigs의 회전력은 크게 향상되어 16배이상 회전수가 증가하는 것으로 나타났다. 이로 인해 100mm 급수관의 세관에서는 통수능이 90%인 노후관이 세관 후 통수능이 완전히 회복되는 것으로 나타났다. 또한 15mm 급수관에 비하여 매우 낮은 압력하에서도 세관효과가 높은 것으로 나타나 관경이 클수록 세관에 필요한 세관압력은 크게 감소되며, 세관효과는 증가되는 것으로 나타났다.

• Membrane and Water Treatment
• /
• 제8권2호
• /
• pp.185-199
• /
• 2017

Low-pressure membrane filtration is increasingly used for tertiary treatment of wastewater effluent organic matter (EfOM), mainly comprising organic base/neutral compounds. In-line coagulation with underdosing, charge neutralization, and sweep floc conditions prior to ultrafiltration (UF) was studied to determine removals of the EfOM components and consequent reduction of fouling using polyethersulfone membranes. Coagulation and UF substantially reduced fouling for all coagulation conditions while removing from 7 to 38% of EfOM organic acids. From 7 to 16% of EfOM organic base/neutrals were removed at neutral pH but there was no significant removal for slightly acid coagulation conditions even though fouling was substantially reduced. Sweep floc produced the lowest resistance to filtration but may be inappropriate for in-line use due to the large added volume of solids. Charge-neutralization resulted in poor recovery of the initial flux with hydraulic cleaning. Under-dosing paralleled sweep floc in reducing hydraulic resistance to filtration (for sub-critical flux) and the initial flux was also easily recovered with hydraulic cleaning. Hydrophobic and hydrophilic base/neutrals were identified on the fouled membranes but as previously reported the extent of fouling was not correlated with accumulation of organic base/neutrals.

• 한국자동차공학회논문집
• /
• 제8권5호
• /
• pp.207-215
• /
• 2000

This study theoretically investigated the roll-off cleanliness operation to eliminate the built-in contaminants which are primarily the result of manufacturing and assembly procedures first. A rigorous analytical examination of the cleaning process associated with hydraulic systems was performed by developing the general filtration process equations. The sloughing process by which built-in contaminant is entrained in the system fluid was examined during the development of a general analytical expression for sloughing rate. This sloughing rate expression in conjunction with the filtration process equations have lead to a relationship rate expression in conjunction with the filtration process equations have lead to a relationship which describes the flushing and clean-up operation for the hydraulic systems. The effects of the primary roll-off cleanliness factors was discussed and illustrated on the figures. Then, the analytical results was shown to be usefully applied into the design of roll-off flushing equipment for the hydraulic system of a tractor.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.1122-1123
• /
• 2005

• 한국물환경학회지
• /
• 제25권1호
• /
• pp.120-124
• /
• 2009

This study was performed to investigate the application of submerged membrane bioreactor (MBR) system for biological nutrient removal of municipal wastewater. MBR bioreactor consists of four reactors such as anaerobic, stabilization, anoxic and submerged membrane aerobic reactors with two internal recycles. The hydraulic retention time (HRT), sludge retention time (SRT) and flux were 6.2 hr, 34.1 days and $19.6L/m^2/hr$ (LMH), respectively. As a result of operation, the removal efficiency of $COD_{Cr}$, SS, TN and TP were 94.3%, 99.9%, 69.4%, and 74.6%, respectively. There was no significant effect of microbial activity after the maintenance cleaning using 200 mg/L of NaOCl. Membrane filtration for the treatment of municipal wastewater was performed for longer than 9 months without chemical recovery cleaning.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1672-1675
• /
• 2003

In this study, we developed full automation test system for pressure vessel. This pressure vessel containing oxygen, nitrogen and carbon is widely used in industrial field. The test items of pressure vessel are divided into three branches which is weight measurement, water-hydraulic, and leakage test. After leakage test is completed, cleaning and dry progress is carried out. And control system is consist of three controller which is PLC, monitoring system and database system. PLC is control all of system. Monitoring system measures weight, pressure, flow etc and display to all conditions. Database system stores tested data. we design system to control all test modules in communication by a second period with three control modules. Finally, we verified this system by field test.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권1호
• /
• pp.55-59
• /
• 2004

This study developed a fully automated test system for pressure vessels, containing such as oxygen, nitrogen, which is widely used in many industries. The pressure vessel test has three major parts including weight measurement test, water-hydraulic test and leakage test followed by cleaning and drying. The control system for these tests consists of three parts: a PLC, a monitoring system and a database management system. The PLC oversees overall control of test machines, while the monitoring system measures and displays weight, pressure, flow etc. for every situations, and the database management system stores test data. These three modules are designed to communicate with one another at 1 Hz frequency alerting problematic situations to the operator. The system has gone through actual field tests for verification of performances.

• Design & Manufacturing
• /
• 제12권1호
• /
• pp.41-46
• /
• 2018

This study proves the causes of cylinder and piston jam by scratches which is the fatal problem of hydraulic breaker through the thermal analysis and thermal-structural coupled field analysis. The trouble from the scratch is a complex problem which can be caused by manufacturing process (this is an internal factor) and the users mistake or contamination in the hydraulic circuit (these are an external factor). Hence, it's not easy to investigate the causes, also hard to prevent the recurrence. In this reason, hydraulic breaker manufacturers are trying to improve the manufacturing process such as machining, heat treatment, grinding, cleaning, also to prevent the contamination in hydraulic circuit and to remove the remains. It's being managed thoroughly by manufacturers. This study shows the effect of the temperature rise by the frictional heat generated when the piston hits the tool on the hydraulic oil while the hydraulic breaker is operating, also the temperature distribution when it starts to affect main components of hydraulic breaker. The stress and the amount of deformation also could be found through thermal-structural coupled field analysis. It proved that the stress and deformation are proportionally increased according to the temperature rise in hit area, and it affects the cylinder and the viscosity of hydraulic oil inside the cylinder when it heats up beyond the certain temperature.