• Journal of the Korean Geotechnical Society
• /
• v.22 no.8
• /
• pp.119-127
• /
• 2006

Granulated Blast Furnace Slag (GBFS) is produced in the manufacture process of pig-iron and shows a similar particle formation to that of natural sea sand and also shows light weight, high shear strength, well permeability, and especially has a latent hydraulic property by which GBFS is solidified with time. Therefore, when GBFS is used as a backfill material of quay or retaining walls, the increase of shear strength induced by the hardening is presumed to reduce the earth pressure and consequently the construction cost of harbor structures decreases. In this study, using the model sand box (50 cm$\times$50 cm$\times$100 cm), the model wall tests were carried out on GBFS and Toyoura standard sand, in which the resultant earth pressure, a wall friction and the earth pressure distribution at the movable wall surface were measured. In the tests, the relative density was set as Dr=25, 55 and 70% and the wall was rotated at the bottom to the active earth pressure side and followed by the passive side. The maximum horizontal displacement at the top of the wall was set as ${\pm}2mm$. By these model test results, it is clarified that the resultant earth pressure obtained by using GBFS is smaller than that of Toyoura sand, especially in the active-earth pressure.

• Korean Journal of Environmental Agriculture
• /
• v.33 no.3
• /
• pp.164-168
• /
• 2014

BACKGROUND: Increase in application of liquid pig manure(LPM) in agriculture as nutritional source has become a social issue due to its influence on water quality. Also, proper application methods have not been developed with respect to indigenous properties of LPM and soil physical properties. Therefore, we conducted this experiment to observe the infiltration characteristics and distribution of dissolved organic compounds of LPM in soils having different soil textures. METHODS AND RESULTS: To do this experiment, we collected three different soils and LPM. We analyzed the physical and chemical properties of both soils and LPM to determine the dilution ratios of LPM. The LPM diluted to 4 different ratios with distilled water was applied to the top of soil column. Infiltration rates were observed by time and depth until the amount of effluent collected from the bottom of the soil columns were stabilized while maintaining the hydraulic head 3 cm above the soil column. The results showed that infiltration rates increased with increasing dilution ratios in the order of sandy, loamy sand, and sandy loam. The time required to reach steady state was increased with decreasing sand contents clay. CONCLUSION: The size and amount of the dissolved organic compounds in LPM that can determine the efficiency as fertilizer and environmental problems as nonpoint pollution source in water quality have not been investigated with respect to behavior and transport of them in soil. Therefore, it requires further research how we can properly apply LPM as valuable fertilizer substitute for inorganic fertilizers.

• Korean Journal of Soil Science and Fertilizer
• /
• v.48 no.3
• /
• pp.194-204
• /
• 2015

Six study sites in Gumi, Goryeong in Gyeongbuk province and Naju in Jeonnam province were selected to investigate soil properties of poorly drained horizons in paddy soils. The horizons were re-established layers which were parent material layers originated from fluvial deposits. Topsoil layers were differentiated from piled parent materials while soil structure of the topsoil layer was massive with striated microstructure. Compaction at soil re-establishment and a lack of structure and aggregate development in these soils may cause the limitation of vertical water movement and result in poorly drained horizons. Soil samples were taken from paddy fields with top soils of sandy loam, silt loam and silty clay loam and re-established soils of coarse and fine texture. The samples were taken from each horizon for the analyses of soil chemical and mineral properties. Soils with re-established soils of coarse texture had greater amounts of sands from top soil texture distributions, while soils with fine texture had greater amounts of silts. Chemical properties of top soils were analyzed from rice cultivated soils at the time of re-establishments and one year after the re-establishments. The coarse texture of the re-established horizons decreased in EC values from 0.23 to $0.11(dS\;m^{-1})$, available phosphate values from 112 to $54(mg\;kg^{-1})$, and exchangeable Ca values from 6.6 to $4.9(cmol_c\;kg^{-1})$. On the other hand, soils with fine texture showed decrease only in pH and exchangeable Ca values. Especially, organic matter and available phosphate contents showed heterogeneous distributions from each horizon. This result may be caused by mixture of plough layer and subsurface layer during and consolidation. Hydraulic conductivity values were low at the boundaries of top soil and parent material layers except SL/coarse soil. Soil microstructure was massive structure without soil clods or pores and showed striated structure. Therefore, re-established paddy fields with fluvial deposits as parent material layers showed limited vertical movements of soil water because of occurrence of compacted layers and less-development of soil clods and aggregates.

• The Journal of Engineering Geology
• /
• v.15 no.4 s.42
• /
• pp.407-421
• /
• 2005

This study aims to investigate hydrogeological properties of the central area from Yangjeong-Dong to Sujeong-Dong in Busan Metropolitan City. For this study, pumping tests were carried out in the bedrock aquifer of Yangjeong-Dong and the unconsolidated aquifer near Busanjin railway station. The pumping test in the bedrock aquifer containing the Dongrae fault revealed specific hydraulic characteristics with respect to the fault. The pumping test in the unconsolidated aquifer revealed the hydrogeologic properties of both coastal landfill and fine sediments. It was found that the Moench's sphere-shaped dual-porosity model fits the bedrock aquifer, whereas the Neuman's uncofined aquifer model accords with the unconsolidated aquifer. The average transmissivity and storage coefficient of the bedrock aquifer are $2.75{\times}10^{-5}m^2/s\;and\;6.41{\times}10^{-5}$ and those of the unconsolidated aquifer are $8.24{\times}10^{-4}m^2/s\;and\;3.70{\times}10^{-3}$, respectively. On the other hand, slug tests gave average transmissivity and storage coefficient values of $9.84{\times}10^{-4}m^2/s\;and\;1.21{\times}10^{-2}$, respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.76-85
• /
• 2017

In this study, to evaluate the mechanical properties of fiber-reinforced cement composites by strain rate, hydraulic rapid loading test system was developed. And compressive and tensile strength of the hooked steel fiber and polyamide fiber reinforced cement composite were evaluated. As a result, the compressive strength, strain capacity and elastic modulus were increased with increasing strain rate. The effect of compressive strength by type and volume fraction of fibers was not significant. The dynamic increase factor(DIF) of the compressive strength was higher than that of the CEB-FIP model code 2010 and showed a trend similar to that of ACI-349. The tensile strength and strain capacity were increased with increasing strain rate. The hooked steel fibers were drawn from the matrix. The tensile strength and strain capacity of hooked steel fiber reinforced cement composites were increased as the strain rate increased. The tensile strength and deformation capacity of the fiber reinforced cement composites were increased. And, hooked steel fibers were drawn from the matrix. On the other hand, because the bonding properties of polyamide fiber and matrix is large, polyamide fiber was cut-off with out pullout from matrix. The strain rate effect on the tensile properties of polyamide fiber reinforced cement composites was found to be strongly affected by the tensile strength of the fibers.

• Tunnel and Underground Space
• /
• v.23 no.3
• /
• pp.169-179
• /
• 2013

Well testing in unconventional reservoirs, such as tight or shale gas formations, presents considerable challenges. It is difficult to estimate the reservoir properties in ultra-low permeability formation because of poor inflow prior to stimulation and excessive test duration. Moreover, radial flow may not develop in hydraulically fractured horizontal wells. For these reasons, the cost of test is high and the accuracy is relatively low. Accordingly, industry is turning to an alternate testing method, diagnostic fracture injection test (DFIT), which is conducted prior to the main hydraulic fracture treatments. Nowadays, DFIT are regarded as the most practical way to obtain good estimates of reservoir properties in unconventional reservoirs. Various methods may be used for interpreting DFIT data. This paper gives an explanation of those methods in detail and examines three actual field data. These show how various analysis methods can be applied to consistently interpret fracture closure pressure and time, as well as before and after closure flow regimes and reservoir properties from field data.

• Ecology and Resilient Infrastructure
• /
• v.8 no.4
• /
• pp.212-222
• /
• 2021

In this study, the flow resistance coefficient was calculated considering the physical properties and distribution characteristics of floodplain vegetation, and the effect of floodplain vegetation distribution on flow characteristics was analyzed by reflecting it in a two-dimensional numerical simulation. The three-dimensional point clouds of vegetation acquired using ground lidar were analyzed to apply floodplain vegetation's physical properties to the existing formula for vegetation flow resistance calculation. The floodplain vegetation distribution in the modeling was divided into locally distributed and fully distributed conditions in the floodplain. As a result of the simulation of the study site, the flow resistance coefficient of floodplain vegetation was found to have a value of about five times or more compared to the flow resistance coefficient of the main channel bed when the design flood occurs based on Manning's n coefficient. Also, it affected the hydraulic characteristics in the main channel and floodplain.

• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.461-468
• /
• 2004

In order to characterize hydraulic property dependant on join roughness in rock mass, this study computed permeability coefficients on each range of joint roughness coefficient (JRC) suggested by Barton(1976). For a quantitative analysis of roughness components spectral analysis using the fast fourier transform was performed to select effective frequencies on each PC range. The results of spectral analyses show that low ranges of the JRC are mainly composed of low frequency domain, while high ranges of the JRC have dominant components at high frequency domain. The inverse Fourier transform made it possible to generate joint models of each JRC range using the effective frequencies of roughness spectrum. The homogenization analysis was applied to calculate permeability coefficient at homogeneous microscale, and then, computes a homogenized permeability coefficient (C-permeability coefficient) at macro scale. Therefore, it is possible to analyze accurate characteristics of permeability reflected with local effect of facture geometry. According to the calculation results, permeability coefficients were distributed between $10^{-3}m/sec\;and\;10^{-4}/sec$. In cases of sheared joint models permeability coefficients were plotted between $10^{-4}m/sec\;and\;10^{-5}/sec$, showing irregular distribution of permeability coefficients on each IRC range. The differences of permeability coefficients for the same aperture models or for the sheared joint models indicate that changes of roughness pattern influence on permeability coefficients. Therefore, the effect of joint roughness should be considered to characterize hydraulic properties in rock joints.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.2
• /
• pp.132-138
• /
• 2009

Soils originated from limestone, located at the southern part of Kangwon province and Jecheon, Danyang of Chungbuk province are mainly composed of fine texture, have different properties from soils originated from granite and granite gneiss, especially for water movement. This study was conducted for making PTF(Pedo-Transfer Function) for Kfs(field saturaton hydraulic conductivity) estimation, and for investigating the relation between soil particle distribution and the infiltration and percolation rate in soils originated from limestone. Soils used for the experiment were 6 soils of Gwarim, Mosan, Jangseong, Maji, Anmi and Pyongan series. Infiltration and percolation rate for the soil were measured by a disc tension infiltrometer and a Guelph permeameter, respectively. The particle size distribution and organic matter content of the soils were analyzed. Kfs was not related with sand, silt, clay, and organic mattrer (OM) content because of forest soils which contained high gravel, pebble, and cobble content, and O layer with high OM content. After Mosan soil series and O layer of Gwarim series were excluded for the data analysis, Kfs was explained as a linear function with sand and clay content and a exponential function with OM content. As a result, the PTF equation was obtained as Kfs=-4.20558+0.479706*(S)+0.023187*exp(1.829*OM) ($R^2=0.6558^{*}$).

• Analytical Science and Technology
• /
• v.18 no.5
• /
• pp.410-418
• /
• 2005

PCBs had numerous uses such as hydraulic fluid, heat exchange fluid, sealant, lubricant, and carbonless copy paper. They are most likely found in electric utilities, power stations, industrial facilities, electronic manufacturing plants, petrochemical plants, railroad systems, electric equipment repair facilities, mining sites (active or abandoned), and military camps. Due to its outstanding chemical and thermal stabilities and electrical insulation properties, the commercial and industrial products of PCBs, such as Aroclors, Kaneclors, Clophens, Phenaclors etc., had been widely used as thermal oil and transformer oil from 1930s until the 1970s. The transformer oils were analyzed as a main source of polychlorinated biphenyls (PCBs) emission into the environment. Qualitative estimation of oil extracts as carried out with Aroclor 1242, 1248, 1254, 1260. The transformer oils contained the pure and mixed of Aroclor 1242, Aroclor 1254, and Aroclor 1260. Also, commercial screening kit of 20 ppm and 50 ppm were applied to the transformer oil samples.