• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.3
• /
• pp.38-52
• /
• 1997

Aluminum-faced honeycomb-cored sandwich panels as hull plating can provide structural weight savings when compared with the conventional aluminum single panels. The aim of the present paper is to confirm the feasibility of the sandwich panels for the hull material of fast ferries through designing an 80m class proto-type fast passenger/car ferry. For the case study, the structural design for the same principal particulars using the aluminum single panels is also performed, and the design results for the two types will be compared to confirm the weight savings between the two construction methods. The economics of a ship, being comprised of the shipbuilding cost and ship operaing cost, will require a cost analysis including a quantitative comparison between the two construction methods and the results of the cost analysis will be presented. Finally, the reasons why aluminum sandwich panels have not presently been used as the hull material for large size fast vessels will be discussed.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.2
• /
• pp.85-91
• /
• 2016

The most important factor in the structural design of ships and offshore structures operating in arctic region is ice load, which results from ice-structure interaction during the ice collision process. The mechanical properties of ice related to strength and failure, however, show very complicated aspect varying with temperature, volume fraction of brine, grain size, strain rate and etc. So it is nearly impossible to establish a perfect material model of ice satisfying all the mechanical characteristics completely. Therefore, in general, ice collision analysis was carried out by relatively simple material models considering only specific aspects of mechanical characteristics of ice and it would be the most significant cause of inevitable errors in the analysis. Especially, it is well-known that the most distinctive mechanical property of ice is high dependency on strain rate. Ice shows brittle attribute in higher strain rate while it becomes ductile in lower strain rate range. In this study, the simulation method of ice collision to ship hull using the nonlinear dynamic FE analysis was dealt with. To consider the strain rate effects of ice during ice-structural interaction, strain rate dependent constitutive model in which yield stress and hardening behaviors vary with strain rate was adopted. To reduce the huge amount of computing time, the modeling range of ice and ship structure were restricted to the confined region of interest. Under the various scenario of ice-ship hull collision, the structural behavior of hull panels and failure modes of ice were examined by nonlinear FE analysis technique.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.6
• /
• pp.1032-1036
• /
• 2012

A bulking agent is an essential material for composting of high-moisture livestock manure such as pig slurry. Sawdust has been used as the most popular bulking agent but resources are limited in Korea. In this study, the feasibility of rice hull as a bulking agent was examined for composting of solid pig manure. The solid pig manure was mixed with 15% sawdust (PM+SD15), 15% rice hull (PM+RH15), 10% sawdust and 5% rice hull (PM+SD10+RH5), and 5% sawdust and 10% rice hull (PM+SD5+RH10) based on fresh weight. These mixtures were composted for 35 days. The average temperature of the composting file for 35 days was higher in PM+SD10+RH5 and PM+SD5+RH10 than in PM+SD15 and PM+RH15. The mass loss of PM+SD10+RH5 and PM+SD5+RH10 were 36.7 and 36.4%, respectively, which were higher than that of PM+SD15 and PM+RH15. After composting, organic matter content and organic matter/nitrogen ratio in all treatments met the official standards of commercial fertilizers. We concluded that rice hull may be a good bulking agent for pig manure composting when it is used in mixture with sawdust.

• Korean Journal of Environmental Agriculture
• /
• v.39 no.3
• /
• pp.222-227
• /
• 2020

BACKGROUND: Among the biomass conversion techniques of livestock manure, composting process is a method of decomposing organic matter through microorganisms, and converting it into fertilizer in soil. The aerobic composting process is capable of treating cow manure in large quantities, and produces greenhouse gas as CO₂ and N₂O, although it has economical benefit. By using the activated rice hull biochar, which is a porous material, it was intended to mitigate the greenhouse gas emissions, and to produce the compost of which quality was high. Objective of this experiment was to estimate CO₂ and N₂O emissions through composting process of cow manure with different cooperated biochar contents. METHODS AND RESULTS: The treatments of activated rice hull biochar were set at 0%, 5%, 10% and 15%, respectively, during composting cow manure. The CO₂ emission in the control was 534.7 L kg^-1, but was 385.5 L kg^-1 at 15% activated rice hull biochar. Reduction efficiency of CO₂ emission was estimated to be 28%. N₂O emission was 0.28 L kg^-1 in the control, but was 0.03 L min^-1 at 15% of activated rice hull biochar, estimating about 89% reduction efficiency. CONCLUSION: Greenhouse gas emissions during the composting process of cow manure can be reduced by mixing with 15% of activated rice hull biochar for eco-friendly compost production.

• Journal of Advanced Research in Ocean Engineering
• /
• v.1 no.4
• /
• pp.211-226
• /
• 2015

Membrane type Mark III cargo containment system (CCS) is considered in this study to investigate its strength capability under applied loads due to liquefied natural gas (LNG) cargo. A rectangular plated structure supported by inner hull structure is exemplified from Mark III CCS according to classification society's guidance and it is assumed as multi-layered structure by stacking plywood, triplex, reinforced polyurethane (PU) foam and series of mastic upon inner hull structure. Commercially available general purpose finite element analysis package is used to have reliable FE models of Mark III CCS plate. The FE models and anisotropic failure criteria such as maximum stress, Hoffman, Hill, Tsai-Wu and Hashin taking into account the direction dependent material properties of Mark III CCS plate components and their material properties considering a wide variation of temperature due to the nature of LNG together form the strength analysis procedure of Mark III CCS plate. Strength capability of Mark III CCS plate is understood by its initial failure and post-initial failure states. Results are represented in terms of failure loads and locations when initial failure and post-initial failures are occurred respectively. From the results the basic design information of Mark III CCS plate is given.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.211-215
• /
• 2005

The binary Al-Mg alloys are the basis for the 5000 series of non-heat-treatable aluminum alloys. In general, 5000 series of aluminum alleys have a high strength, good welding characteristics and a high resistance to corrosion, especially under the seawater. Thus the aluminum alloys are adopted in the hull material of hovercraft that is required light in weight as well as high strength. It is very important that the weldability problem of these alloys caused by high thermal conductivities welding deformation, porosity and so on. in this study, auto-welding equipment was applied for aluminum welding automation. Also, optimal welding data were studied by investigating welding characteristics for various shapes of weldment to use Al 5083 that is representative structural materials of the 5000 series of aluminum alloys.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.1
• /
• pp.61-67
• /
• 2024

A naval mine is an effective weapon system implemented for defending defends ports and seas. A mine is an underwater weapon that poses a great threat to ships sailing over the sea from shallow areas. Most of the influence-type naval mines detect magnetic field signals from ships and determine the final time of fire. Therefore, the level of underwater electro-magnetic signatures of ships is a key requirement for determining the survival of ships in wartime situations where mines are emplaced. The main reason why the high manganese steel is attracting attention for naval ship hulls is its nature as a non-magnetic steel. The non-magnetic hull does not generate electro-magnetic signatures; thus, it has the advantage improving the stealth of the ship. In this paper, I examine whether this material can be applied in the hulls material of naval ships that must be ableto reduce underwater electro-magnetic signatures by considering the non-magnetic characteristics of the first developed high manganese steel in the world.

• Korean Journal of Organic Agriculture
• /
• v.20 no.4
• /
• pp.475-490
• /
• 2012

Since 1997, Korean Ministry of Knowledge Economy and Ministry of Environment have established data on some 400 basic raw and subsidiary materials and process like energy, petro-chemical, steel, cement, glass, paper, construction materials, transportation, recycling and disposal etc by initiating establishment of LCI database. Regarding agriculture, Rural Development Administration has conducted establishment of LCI database for major farm products like rice, barley, beans, cabbage and radish etc from 2009, and released that they would establish LCI database for 50 items until 2020 later on. The domestic LCI database for seeds, seedling, agrochemical, inorganic, fertilizer and organic fertilizer etc is only at initial stage of establishment, so overseas LCI databases are brought and being used. However, since the domestic and overseas natural environments differ, they fall behind in reliability. Therefore, this study has the purpose to select organic farming materials, survey the production process for various types of organic farming materials and establish LCI database for the effects of greenhouse gas emitted by each crop during the process. As for selecting methods, in this study organic farming materials were selected in the method of direct observation of material and bottom-up method a survey method with focus on the organic farming materials admitted into rice production. For the basic unit of carbon emission amount by the production of 1kg of organic farming material, the software PASS 4.1.1 developed by Korea Accreditation Board under Ministry of Knowledge Economy was used. The study had the goal to ultimately provide basic unit to calculate carbon emission amount in executing many institutions like goal management system and carbon performance display system etc in agricultural sector to be conducted later on. As a result, emission basic units per 1kg of production were calculated to be 0.04968kg-$CO_2$ for oystershells, 0.004692kg-$CO_2$ for expanded rice hull, and 1.029kg-$CO_2$ for bordeaux mixture liquid.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.3
• /
• pp.244-248
• /
• 2000

It was investigated and analized on the construction and hull form for the ordinary fishing boat of south coast in Korea, and then analogized on the shipbuilding technology of fishing boat and fishing type around 1900 by B-spline form parameter method. The results obtained can be summarize as follows : (1) It was known that the boats used in this study have more narrow hull form than that of ancient fishing boats and their hull form was improved around 1900. (2) Keel was composed of bar keel with angle cross section. The stem corner have a material of bar stem and makes a sharp pointed stem. (3) Shell plate was jointed by the rabbetted clinker joint method. (4) It was investigated that anchovy drag net fishing boat has high L/B, L/D, B/D value as compared with drift gill net fishing boat. (5) Two boats have a good stability and particularly anchovy drag net fishing boat have a better stability value in comparison to the drift gill net fishing boat.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.83-97
• /
• 1995

The aim of this study is to derive a simple formula for predicting ultimate strength of hull girders under vertical bending moment. The existing formulas have been reviewed and classified into analytical approach, empirical approach and linear approximate approach. It is known that the ship hull will reach the ultimate limit state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical formula is derived. The accuracy of the formula has been verified by a comparison of the experimental and the numerical results.