• Advances in aircraft and spacecraft science
• /
• 제4권4호
• /
• pp.401-419
• /
• 2017

This paper presents the main outcomes of the preliminary development of the Anuloid, an innovative disk-shaped VTOL aircraft. The Anuloid has three main features: lift is provided by a ducted fan powered by a turboshaft; control capabilities and anti-torque are due to a system of fixed and movable surfaces that are placed in the circular internal duct and the bottom portion of the aircraft; the Coanda effect is exploited to enable the control capabilities of such surfaces. In this paper, results from CFD analyses and wind tunnel tests are presented. Horizontal and vertical flights were considered, including accelerated flight. Particular attention was paid to the experimental analysis of the Coanda effect via a reduced scale 3D printed model. The results suggest that the Coanda effect is continuously present at the lower surface of the Anuloid and may be exploited for the control of the aircraft. Also, very complex 3D flows may develop around the aircraft.

• 대한조선학회논문집
• /
• 제55권1호
• /
• pp.75-82
• /
• 2018

Wedge-shaped fins are generally used to provide sufficient forces and moments to control and maneuver a supercavitating vehicle. There are four fins placed along the girth of the vehicle, near he tail: two of the fins are horizontal and the other two fins are vertical. In a fully developed supercavitating flow condition, a part of the fin is in a cavity pocket and the other is exposed to water. In this paper, experimental investigations of hydrodynamic characteristics of the wedge-shaped fin models are presented. Experiments were conducted at a cavitation tunnel of the Chungnam National University. We first closely observed the typical formation of wake cavitation and measured lift and drag forces acting on two different test models. Next, using a special device for generating natural and artificial supercavities, we investigated hydrodynamic forces at different cavitation number conditions. This work provides a basis for interpreting the cavity stability and hydrodynamic characteristics of the wedge-shaped control fin for a supercavitating vehicle.

• 대한조선학회논문집
• /
• 제53권1호
• /
• pp.10-17
• /
• 2016

When a planing hull straightly runs and turns, its floating position and pitch angle are changed depending on its speed, and large transient motion happens. In this paper, six degrees of freedom(6 DOF) equations of motion, which could simulate the motion of a planing hull, are established. Static and dynamic forces in vertical plane are modeled using pre-calculated displacements and metacentric heights depending on various draft, lift under bottom, and vertical damping coefficients which are used to tune the final motion. Hydrodynamic coefficients in horizontal plane at various equilibrium state are calculated by using Lewandowski's empirical formula and the speed-dependent equilibrium state are calculated beforehand by Savitsky's formula. The speed effects are considered by curve-fitting the coefficients at various speed to the polynomials. Accelerating, decelerating and backing, turning, and zig-zag are simulated and compared with the sea trial results, and it is confirmed that the speed reduction, roll, and pitch during such maneuvers of sea trial and simulation are well consistent.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1315-1320
• /
• 2008

An experimental study was carried out to study the solid-liquid mixture upward flow in a vertical and inclined annulus with rotating inner cylinder. Lift forces acting on a fluidized particle plays a central role in many importance applications, such as the removal of drill cuttings in horizontal drill holes, sand transport in fractured reservoirs, sediment transport and cleaning of particles from surfaces, etc. Field measurements have revealed that the pressure drop over a borehole during drilling of a slim oil well or a well with a long reach can depend significantly on the rotation speed of the drill pipe. An accurate prediction of the annular frictional pressure drop is therefore important for conditions where the annular clearance is small. Effect of annulus inclination and drill pipe rotation on the carrying capacity of drilling fluid, particle rising velocity, and pressure drop in the slim hole annulus have been measured for fully developed flows of water and of aqueous solutions.

• 한국공간구조학회논문집
• /
• 제13권2호
• /
• pp.57-66
• /
• 2013

There are a number of construction methods to build spatial structures such as erection method, Element method, Block method, Sliding method, Lift-up method and Push-up method. These methods are uneconomical and low accuracy, and require long construction duration because of a need of a scaffold or a tower crane to build spatial roof frame. In this study, the construction method to erect a truss structure was proposed as an economical and easy installation method. The proposed method has end hinges of keel truss and winches with horizontal cable. This method makes safe and accurate production and reduces construction duration because trusses are built on the floor or supporter. The goal of this study is to verify the validity of construction method by building scale model using the proposed method.

• Wind and Structures
• /
• 제37권1호
• /
• pp.57-78
• /
• 2023

In this study, a generalized three-degree-of-freedom (3-DoF) analytical model is formulated to predict linear aerodynamic instabilities of a prism under quasi-steady (QS) conditions. The prism is assumed to possess a generic cross-section exposed to turbulent wind flow. The 3-DoFs encompass two orthogonal horizontal directions and rotation about the prism body axis. Inertial coupling is considered to account for the non-coincidence of the mass center and the rotation center. The aerodynamic force coefficients-drag, lift, and moment-depend on the Reynolds number based on relative flow velocity, angle of attack, and the angle between the wind and the cable. Aerodynamic forces are linearized with respect to the static equilibrium configuration and mean wind velocity. Routh-Hurwitz and Liénard and Chipart criteria are used in the eigenvalue problem, yielding an analytical solution for instabilities in galloping and static divergence types. Additionally, the minimum structural damping and stiffness required to prevent these instabilities are numerically determined. The proposed 3-DoF instability model is subsequently applied to a conductor with ice accretion and a full-scale dry inclined cable. In comparison to existing models, the developed model demonstrates superior prediction accuracy for unstable regions compared with results in wind tunnel tests.

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.120-127
• /
• 2016

본 연구에서는 수문의 설치방향에 따른 최적의 설치방향을 규명하기 위하여, 모형 제작에 의한 수문 진동실험을 수행하고, 진동특성이 연구되어진다. 47.5m 원형게이트가 아크릴을 사용하여 1:31 축척으로 제작되고, 납으로 질량이 보완된다. 먼저 모형을 검증하기 위하여 모형의 고유진동수가 측정되고, 원형 수문의 유한요소 해석 값으로 부터 환산된 고유진동수와 비교된다. 모형은 1.6m 폭을 갖는 콘크리트 수로에서 정방향과 역방향 설치에 따른 각각의 실험이 이루어 졌다. 각 방향 실험에서는 수문 개방고와 상하류 수위에 따른 여러 조건에서 수직진동이 측정되어 졌다. 실험결과를 바탕으로 정뱡향과 역방향 설치에 대한 진동현상을 서로 비교 분석하였다. 정방향 모형은 수문이 많이 열렸을 때 하단부의 수평트러스 부재를 치는 뒤돌아 치는 와류에 의하여 진동이 크게 발생하였고, 작은 개방고에서 suction force에 의한 진동이 발생하였다. 그러나 역방향 모형에서는 이러한 현상이 발생하지 않는다. 마지막으로 95m 수문의 진동실험결과와 본 47.m의 실험결과를 같이 비교하여 평가하였다. 실험결과 여러 실험 조건에서 진동이 작게 측정되는 역방향 배치 모형이 더 합리적인 것으로 분석되었다.

• 수산해양기술연구
• /
• 제43권1호
• /
• pp.49-61
• /
• 2007

Otter boards in the trawl are the one of essential equipments for the net mouth to be spread to the horizontal direction. Its performance should be considered in the light of the spreading force to the drag and the stability of towing in the water. Up to the present, studies of the otter boards have focused mainly on the drag and lift force, but not on the stability of otter boards movement in 3 dimensional space. In this study, the otter board is regarded as a rigid body, which has six degrees of freedom motion in three dimensional coordinate system. The forces acting on the otter boards are the underwater weight, the resistance of drag and spread forces and the tension on the warps and otter pendants. The equations of forces were derived and substituted into the governing equations of 6 degrees of freedom motion, then the second order of differential equations to the otter boards were established. For the stable numerical integration of this system, Backward Euler one of implicit methods was used. From the results of the numerical calculation, graphic simulation was carried out. The simulations were conducted for 3 types of otter boards having same area with different aspect ratio(${\lambda}=0.5,\;1.0,\;1.5$). The tested gear was mid-water trawl and the towing speed was 4k't. The length of warp was 350m and all conditions were same to each otter board. The results of this study are like this; First, the otter boards of ${\lambda}=1.0$ showed the longest spread distance, and the ${\lambda}=0.5$ showed the shorted spread distance. Second, the otter boards of ${\lambda}=1.0$ and 1.5 showed the upright at the towing speed of 4k't, but the one of ${\lambda}=0.5$ heeled outside. Third, the yawing angles of three otter boards were similar after 100 seconds with the small oscillation. Fourth, it was revealed that the net height and width are affected by the characteristics of otter boards such as the lift coefficient.

• 한국의류학회지
• /
• 제38권1호
• /
• pp.97-109
• /
• 2014

This study developed a functional dress shirt for adult males that reflected the body surface variation of a human body section by motion. This study conducted a 3D body scan for 8 subjects in their 40's based on the Size Korea 2010 database. Data recorded the proper posture change value and body surface change value to develop functional dress shirts for adult males. We scanned the subjects with a 3D body scanner for five primarily male wearing dress shirts and operating postures, right standing, arms raised to $90^{\circ}$ horizontal forward position, arms raised $90^{\circ}$ to the horizontal position side, lift up the arm $180^{\circ}$, and arm forward $90^{\circ}$ in a bent posture. We analyzed the 3D scan data from those motions to examine change of length using 3D software Rapidform XOS. The results indicated that the body surface sections with contraction were the front and rear shoulder area, armpit and central length as well the width of arms at more than 10%. The increased body section included the body and armpit back length; in addition, the rear arm vibration girth and under arm girth were more than 10%. In order to reflect the size variation of for each motion, the ease amount of the front and rear shoulder length and width needs to be reduced 20% because it affects the shoulder length during the right standing. The results suggest that the ease amount of the shoulder length should be minimal. The ease amount of the back size needs to be 0.5-2cm bigger and set 0.5-1.5cm longer than the dress shirt length side drooping to compensate for the side length shortage of each motion. The sleeve length needs to be 0-0.5cm shorter, and ease amount of the girth of sleeve bottom needs to be reduced 0-0.7cm due to the size variation of arms. However, the girth of the rear arms is suggested to be 0-0.6cm longer in the ease amount to the rear arm girth as the extension is more than 10% over the width and length of each motion.

• 한국지구과학회지
• /
• 제28권7호
• /
• pp.857-870
• /
• 2007

명시적 액체-얼음상 미시물리 과정을 포함하는 구름 분해 모형(ARPS: Advanced Regional Prediction System)을 이용하여 2차원 그리고 주변 바람이 없는 경우에 뇌우 유출의 구조와 진화를 조사하였다. 고해상도 격자 간격(50m)을 이용하여 유출의 난류 구조를 명시적으로 분해하였다. 모사된 단세포 스톰과 스톰과 연관된 Kelvin-Helmholtz(KH) 빌로우(billow)는 발달, 성숙, 소멸의 생애 단계를 가졌다. 구름 역학과 미시물리 사이의 상호작용으로 야기된 이차 맥동과 대류 세포의 분활이 관측되었다. 상대적으로 건조한 하층 대기를 낙하하는 빗방울과 우박의 증발에 기인한 찬 하강류는 뇌우 찬 공기 유출을 야기시켰다. 유출 머리는 거의 일정한 속도로 이동하였다. KH 불안정에 의해 생성된 KH 빌로우는 유출 상부에서 난류 혼합을 야기하였으며 유출의 구조를 지배하였다. KH 빌로우는 유출 머리에서 생성되었고 돌풍 전선에 상대적으로 뒤쪽으로 이동함에 따라 성장하고 소멸하였다. 가장 빨리 성장하는 섭동의 수평 파장과 임계 시어층 깊이의 비 그리고 KH 빌로우의 수평 파장과 최대 진폭의 비에 대한 수치 모사 결과는 다른 연구 결과와 잘 일치하였다.