• 한국안전학회지
• /
• 제33권4호
• /
• pp.46-53
• /
• 2018

This study examined the maximum resistant moment and nonlinear rotational stiffness of wedge joint between the vertical and horizontal members of system supports. To examine the maximum resistant moment and propose the nonlinear rotation stiffness of wedge joint, 6 specimens were tested and additional 3 specimens, where the horizontal member was welded to the vertical member, were tested to compare the moment capacity of wedge joints. The average maximum moment in the tested wedge joint was 1.183 kNm which represented about 70 % of the maximum moment developed in the welded specimens. And, as simulating nonlinear rotational stiffness of the wedge joint, a tri-linear model was suggested. The rotational stiffness was estimated as 23.095 kNm/rad in first stage, 7.945 kNm/rad in second stage, and 3.073 kNm/rad in third stage. For the failure mode, the specimen with the wedge joint showed the failure of joint between vertical and horizontal members. However, the specimen with welded joint represented the yielding of horizontal members.

• 콘크리트학회지
• /
• 제8권4호
• /
• pp.171-179
• /
• 1996

PC판넬 조립식 구조의 수직.수평접합부의 유용한 접합형태에 따라 접합부 전단내력을 상승시킬 수 있는 접합부 설계의 기본 형태를 제시하는데 연구의 목적이 있다. 시험체는 수직접합부의 경우 전단키의 개수 및 보강철물의 종류에 변수를 주고 수평접합부의 경우에는 전단키의 갯수 및 가력방향에 변수를 주어 총 22개의 시험체를 제작하여 실험하였다. 결론적으로 수직접합부의 경우, 수평보강철물이 있는 시험체는 기존의 다른 실험결과와 마찬가지로 수평보강철물이 없는 시험체에 비하여 연성이 크게 나타났다. EH한 와이어로프와 원형철근 두 종류의 보강철물을 사용하여 실험한 결과 와이어 로프를 사용한 시험체는 원형철근을 사용한 시험체와 최대내력 및 전단강성 등 전체적인 구조거동이 거의 비슷하게 나타났다.

• 콘크리트학회지
• /
• 제6권2호
• /
• pp.138-147
• /
• 1994

대형 콘크리트 판넬구조 수평접합부는 상부로부터 전달되는 축하중에 대하여 저항하게 되며 이때의 저항내력은 그라우트와 판넬의 강도, 접합부의 형태 및 단부 모멘트, 그라우트의 폭 등에 따라 변하게 된다. 본 연구는 패쇄형 수평접합부에 대한 실험연구로서 슬래브의 단부형태, 벽판넬의 단부보강 및 슬래브의 횡변위 구속에 따른 내력의 변화를 관찰하고자 하였다. 현재 대형 콘크리트 패널구조 수평접합부의 설계에 적용되고 있는 국내 규준식은 국내의 대형 콘크리트 패널구조와는 다소 다른 형태의 실험결과에 의해 유도된 식으로서 그 적용성에 대한 평가가 요망된다. 따라서 본 연구에서는 실험결과를 근거로 이에 대한 평가를 실시할 뿐만 아니라 폐쇄형 수평접합부의 내력을 평가할 수 있는 적합한 이론식을 제시 하였다. 실험결과, 상부 벽판넬의 단면이 결손(10mm)됨에 따라 약 23.5% 내력이 저감되는 것으로 나타났으며, 슬래브 단부형태의 따른 차이와 벽판넬의 단부보강에 따른 내력의 차이, 슬래브의 횡변위 구속 유무에 따른 내력의 차이는 거의 없는 것으로 나타났다. 또한, 제안되 이론식과 실험결과를 비교한 결과 이론식에 의한 결과가 실험결과와 좋은 대응을 보이는 것으로 나타났다.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.565-576
• /
• 2020

Experimental and discrete element methods were used to investigate the effects of angle of Y shape non-persistent joint on the tensile behaviour of joint's bridge area under brazilian test. concrete samples with diameter of 100 mm and thikness of 40 mm were prepared. Within the specimen, two Y shape non-persistent notches were provided. The large notch lengths were 6 cm, 4 cm and 2 cm. the small notch lengths were 3 cm, 2 cm and 1 cm. The angle of larger notch related to horizontal axis was 0°, 30°, 60°, 90°. Totally, 12 different configuration systems were prepared for Y shape non-persistent joints. Also, 18 models with different Y shape non-persistent notch angle and notch length were prepared in numerical model. The large notch lengths were 6 cm, 4 cm and 2 cm. the small notch lengths were 3 cm, 2 cm and 1 cm. The angle of larger notch related to horizontal axis was 0, 30, 60, 90, 120 and 150. Tensile strength of model materil was 1 MPa. The axial load was applied to the model by rate of 0.02 mm/sec. This testing showed that the failure process was mostly governed by the Y shape non-persistent joint angle and joint length. The tensile strengths of the specimens were related to the fracture pattern and failure mechanism of the discontinuities. It was shown that the tensile behaviour of discontinuities is related to the number of the induced tensile cracks which are increased by increasing the joint length and joint angle. The minimum tensile strength occurs when the angle of larger joint related to horizontal axis was 60°. Also, the maximum compressive strength occurs when the angle of larger joint related to horizontal axis was 90°. The tensile strength was decreased by increasing the notch length. The failure pattern and failure strength are similar in both methods i.e. the experimental testing and the numerical simulation methods.

• 한국운동역학회지
• /
• 제17권3호
• /
• pp.115-124
• /
• 2007

The purpose of this study was to analyze the kinematics variables of upper limb joint during forehand stroke by swings patterns. Eight high school tennis players were chosen for the study, who have never been injured for last six months, in Busan. They performed horizontal swing and vertical swing that it was done each five consecutive trial in the condition of square, semi-open and open stance. It was filmed by 6 video camera and used with 3-dimensional motion analyzer system. The following kinematic variables were analyzed in relation to angle of joint(shoulder, elbow and wrist joint). The conclusion were as follow: 1. The angle of right shoulder joint represented all event that both swing were shown similar pattern in swing type and stance pattern. 2. All event in the angle of elbow joint had consistent with that except E2, horizontal and vertical swings in square stance. 3. All event in the angle of wrist joint was show to similar pattern except E2, horizontal and vertical swing in open stance.

• 한국도로학회논문집
• /
• 제3권1호
• /
• pp.165-176
• /
• 2001

줄눈콘크리트포장의 줄눈은 온도 및 습도변화에 기인하여 발생하는 슬래브내에 무작위하게 발생하는 균열을 제어할 목적으로 설계된다. 이러한 인위적인 균열 (줄눈)은 자연발생적인 균열에 비하여 줄눈채움, 하중전달장치등의 보호대책을 강구하는 것이 용이하다는 장점을 가지고 있다. 줄눈채움의 잠재적인 이점은 표면수의 하부층으로의 침투로 인한 하부층의 약화 및 비압축성 물질 (작은 입자위 골재)의 줄눈내에 끼어듦으로 인한 스폴링을 방지하는데 있다. 합리적인 줄눈 채움의 설계를 위해서는 줄눈폭의 변화 (줄눈의 수평 움직임)의 산정이 중요한 입력요소이다. LTPP SMP 연구에 포함된 16개의 줄눈콘크리트포장의 줄눈의 수평움직임에 대한 장기 현장계측자료를 토대로 상당수의 줄눈에서 수평움직임을 허용하지 않고 있다는 것이 밝혀진바 있다. 이러한 현상을 줄눈잠김이라고 한다. 줄눈잠김이 발생하는 원인은 설계상에 계획된 줄눈부의 균열이 발생하지 않기 때문이라고 추정된다. 본 연구에서는 임의의 줄눈콘크리트포장에서 줄눈잠김의 비율을 예측할 수 있는 모델을 제시하였고 줄눈 잠김이 포장체의 성능에 미치는 영향을 조사하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 봄 학술발표회 논문집
• /
• pp.19-24
• /
• 1994

Four types of horizontal joint were tested to investigate the difference with regards to the compressive behavior and strength. These include wedge-type joints (i)with and (ii)without transverse reinforcement against splitting failure of the panel concrete, and wedge-type joints (iii)with different widths of joint concrete (6cm vs 8cm) and (iv)closed platform joint. It was shown that the compressive strength of wedge-type joint is about 10% higher than that of closed-type (platform) joint. But the effect of transverse reinforcement and joint concrete widths on the strength of the joints turned out be negligible. Also, the moduli of elasticity in panel and joint are compared and the equivalent moduli of the whole wall are derived.

• Clinics in Shoulder and Elbow
• /
• 제25권3호
• /
• pp.224-229
• /
• 2022

Background: Most acromioclavicular joint (ACJ) injuries are caused by direct trauma to the shoulders, and various methods and techniques are used to treat them; however, none of the options can be considered the gold standard. This study examines the horizontal stability of the ACJ after a complete dislocation was repaired using one of two Ethibond suture techniques, the loop technique and the two holes in the clavicle technique. Methods: In this single-blind, randomized clinical trial, 104 patients diagnosed with complete ACJ dislocation type V were treated using Ethibond sutures with either the loop technique or the two holes in the clavicle technique. Horizontal changes in the ACJ were radiographically assessed in the lateral axial view, and shoulder function was evaluated by the Constant (CS) and Taft (TS) scores at intervals of 3, 6, and 12 months after surgery. Results: The horizontal stability of the ACJ was better with the two-hole technique than the loop technique at all measurement times. CS and TS changes showed a significant upward trend over time with both techniques. The mean CS and TS at the final visit were 95.2 and 11.6 with the loop technique and 94.0 and 11.9 with the two-hole technique, respectively. The incidence of superficial infections caused by the subcutaneous pins was the same in the two groups. Conclusions: Due to the improved ACJ stability with the two-hole technique, it appears to be a more suitable option than the loop technique for AC joint reduction.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 가을 학술발표회 논문집
• /
• pp.113-120
• /
• 1994

Large Concrete Panel Structures behave quite differently from frame or monolithic shear wall structures because of the weakness of Joint in stiffness and strength. The joint experiences large deformation such as shear-slip in vertical and horizontal joint and rocking and crushing in horizontal joint because of localized stress concentration, but the wall panels behave elastically under cyclic loads. In order to describe the nonlinear behavior of the joint in the analysis of PC structures, different analysis technique from that of RC structures is needed. In this paper, for analysis of large concrete panel subassemblage subjected to cyclic loads, the wall panels are idealized by elastic finite elements, and the joints by nonlinear spring elements with various load-deflection relationship. The analytical results are compared with the experimental results on the strength, stiffness, energy dissipation and lateral drift, and the effectiveness of this computer analysis modelling technique is checked.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.597-602
• /
• 1997

The compressive strength of horizontal joints in precast concrete large panel structures depends on parameters such as grout and panel strength, detail of joint, joint moment, width of grout column etc. As the panels are only connected at the pocket, it results in the reduction of compressive strength area. The purposes of this study are to develop the suitable grout material the joint pocket and to enable us to evaluate structural capacity. The validity of the design formulas provides us more economic system in construction. Test results of 15 specimens show that the proper construction procedure and grouting material develop the sufficient compressive strength of the wall as monolithic system.