• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.224-231
• /
• 1990

To improve the dispersion of platinum catalyst, the effects of carbon black surface treatment, solvents, surfactants, and ultrasonic homogenizing were examined. Upon introducing the hydrophilic groups acting as an anchorage center of the catalyst on the surface of carbon black by oxidation, the migrating and growing of platinum particles(or ions) during reduction could be restricted. When mixed solvents, surfactants, or ultrasonic homogenizer were used to disperse catalysts on the carbon black, the dispersion of catalyst could be improved, due to the good permeation of chloroplatinic acid through the pore of carbon black. Among the impregnation methods, the method using ultrasonic homogenizer with mixed solvent was the most excellent. Using this method the particle sized could be minimized in less than $30A^{\circ}$ and distributed homogeneously.

• Applied Chemistry for Engineering
• /
• v.3 no.4
• /
• pp.701-709
• /
• 1992

Silver particles were impregnated on carbon black with colloidal method and used as catalyst for oxygen electrode in alkaline fuel cell. With the addition of sodium dodecylbenzenesulfonate in $AgNO_3$ and $NaBH_4$solution, colloidal solution was made and confirmed with electrophoresis test. Effects of particle size on electrode performance were studied and $200{\AA}$ of silver particle size shown the highest value of mass activity. The aggromeration of silver particle was Influenced with surfactant amount, stirring time and heat treatment. Considering the increase of particle size caused of operating temperature, recommendable particle size of silver catalyst for manufacturing the electrode was $100{\AA}$. Dispersity of carbon black was investigated and reagglomeration was appeared after homogenizing 30 sec.

• Food Science and Preservation
• /
• v.10 no.2
• /
• pp.192-199
• /
• 2003

To prepare soybean curd utilizing effectively bioactive component of soybean, ultra fine whole soybean flour(UFWSF) was used as a soybean curd material for preparation of uncompressed whole soybean flour curd(UWSFC) in this study. The UWSFC was made with treatment by proteinase and coagulant, and proximate composition, color, textural properties and sensory evaluation of that were analyzed. Protease produced from Aspergillus sojae, bromelain and papain showed soybean curd coagulation ability and the pretense produced from Aspergillus sojae showed the highest soybean curd coagulation ability. When, after first heating and homogenizing, the proteinase was added to soybean milt textural properties of UWSFC were the best. Hunter's L and b values and textural properties (hardness, fracturability springiness, gumminess and chewiness) of UWSFC using proteinase and coagulant were higher than commercial soft soybean curd and adhesiveness and cohesiveness showed contrary tendency.

• Journal of Korea Foundry Society
• /
• v.20 no.2
• /
• pp.104-109
• /
• 2000

Three different white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their abrasion wear behavior in as-cast and heat-treated conditions. The specimens were produced using a 15㎏-capacity high frequency induction furnace. Melts were super-heated to $1600^{\circ}C$, and poured at $1550^{\circ}C$ into Y-block pepset molds. Three combinations of the alloying elements were selected so as to obtain the different types of carbides : 3%C-10%Cr-5%Mo-5%W(alloy No. 1: $M_7C_3$ and $M_6C$), 3%C -10%V-5%Mo-5%W(alloy No. 2: MC and $M_2C$) and 3%C-17%Cr-3%V(alloy No. 3: $M_7C_3$ only). A scratching type abrasion test was carried out in the states of as-cast(AS), homogenizing(AH), air-hardening(AHF) and tempering(AHFT). First of all, the as-cast specimens were homogenized at $950^{\circ}C$ for 5h under the vacuum atmosphere. Then, they were austenitized at $1050^{\circ}C$ for 2h and followed by air-hardening in air. The air-hardened specimens were tempered at $300^{\circ}C$ for 3h. 1 ㎏ load was applied in order to contact the specimen with abrading wheel which was wound by 120 mesh SiC paper. The wear loss of the test piece(dimension: $50{\times}50{\times}5$ mm) was measured after one cycle of wear test and this procedure was repeated up to 8 cycles. In all the specimens, the abrasion wear loss was found to decrease in the order of AH, AS, AHFT and AHF states. Abrasion wear loss was lowest in the alloy No.2 and highest in the alloy No.1 except for the as-cast and homogenized condition in which the alloy No.3 showed the highest abrasion wear loss. The lowest abrasion wear loss of the alloy No.2 could be attributed to the fact that it contained primary and eutectic MC carbides, and eutectic $M_2C$ carbide with extremely high hardness. The matrix of each specimen was fully pearlitic in the as-cast state but it was transformed to martensite, tempered martensite and austenite depending upon the type of heat-treatment. From these results, it becomes clear that MC carbide is a significant phase to improve the abrasion wear resistance.

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.316-327
• /
• 1998

This study was designed to examine the tissue levels of interleukin-$1{\alpha}$(IL-$1{\alpha}$), interleukin-$1{\beta}$(IL-$1{\beta}$) and tumor necrosis factor-${\alpha}$(TNF-${\alpha}$) in inflamed human dental pulps and periapical lesions, and to determine the relationship between each cytokine and pulpal and periapical pathosis. The pulps used in this experiment, were obtained in routine endodontic treatment and the periapical lesions in periapical surgery after clinical diagnoses were performed. These specimens were divided into four groups as normal pulp group(control group, n=9), acute pulpitis group(n=g), chronic pulpitis group(n= 10) and periapical lesion group(n= 18) and stored in liquid N2. For extract preparation, tissues were finely minced with a scalpel, and the fragments were incubated in $0.5m\ell$ homogenizing buffer (0.1 mol/L potassium chloride, 0.02 mol/L TRIS; pH=7.6) for two hours and grinded with glass homogenizer. Debris was removed by centrifugation and supernatants were immediately tested with enzymelinked immunosorbent assay (ELISA, R&D Co., Minneapolis, USA). Following results were obtained; 1. The concentrations of IL-$1{\alpha}$ in all experimental groups were significantly higher than in control group(p<0.05). And the concentrations of IL-$1{\alpha}$ in periapical lesion group were somewhat higher than in two pulpitis groups, but the differences among those groups were not stastically significant (p>0.05). 2. The concentrations of IL-$1{\beta}$ in all experimental groups were significantly higher than in control group (p<0.05), and all the experimental groups expressed similar concentrations. 3. The concentrations of TNF-${\alpha}$ in all experimental groups were higher than in control group but only the differences between chronic pulpitis group and control group were statistically significant(p<0.05). And the concentrations of TNF-${\alpha}$ in acute and chronic pulpit is groups were higher than in periapical lesion group but only the differences between chronic pulpitis group and periapical lesion group were statistically significant (p<0.05). 4. There was significant correlation only between IL-$1{\alpha}$ and IL-$1{\beta}$ in periapical lesion group (p<0.05).