• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.51-59
• /
• 2000

In-cylinder spray flow motion plays an important in the adjustment of mixture preparation with a fundamental spray characteristics and in-cylinder flow field well in direct-injection gasoline engine. In this study, the fundamental spray characteristics such as mean drop size, velocity distribution, spray angle were measured and in-cylinder spray flow motion was visualized in order to optimize intake port, piston top land and combustion chamber shapes in the development stage of mass-produced G야 engine. For these experiments, the PDPA measurements and Mie scattering technique were used for detailed spray characteristics and in-cylinder spray motions were obtained by use of ICCD camera through the single-cylinder optical engine. From the experimental results, the test injector shows a good low-end linearity between the dynamic flow and fuel injection pulse width and the fuel spray of 20mm or less in SMD with good spray symmetry. In addition, the in-cylinder tumble flow has more effect on the homogeneous mixture formation than that of in-cylinder swirl flow at early injection mode and the in-cylinder swirl flow plays a better role of stratified mixture preparation than tumble flow at late injection mode.

• Journal of Institute of Convergence Technology
• /
• v.9 no.1
• /
• pp.13-19
• /
• 2019

The purpose of this study is to suggest a new method to determine a combustion phase (start of combustion and end of combustion) using a combustion pressure data. Unlike previous research method that used heat release amount, the difference between the combustion pressure measured in the combustion chamber and the motoring pressure was used to determine the combustion phase. This research was conducted using a single-cylinder diesel engine with a compression ratio of 17.7. The test was conducted under various injection timing. The newly proposed method showed high accuracy in combustion mode with early injection, as well as the conventional combustion mode. It is expected that this method will be used to study new combustion strategies such as HCCI (homogeneous charge compression ignition) and RCCI (reactivity controlled compression ignition) that are applying early injection strategies as well as existing combustion modes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.294-295
• /
• 2006

Field sequential liquid crystal display (FSLCD) has advantages such as a high transmittance due to no use of color filter and high color reproductivity because of LED backlight for a luminance source. However, to realize FSLCD response time of the LCD must be below 5ms. In this paper, we have chosen electrically controlled birefringence (ECB) mode for this application and studied film compensation to improve the operating voltage and viewing angle and to achieve a fast response time optimizing the condition of the discotic film and TAC film, operating voltage decreases to 5V, and viewing angle range is $160^{\circ}$ at horizontal and vertical direction, respectively and $120^{\circ}$ in diagonal direction. (contrast ratio > 10:1) and optimized cell exhibits a fast response time of 4ms in most grey levels.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.1-14
• /
• 2007

In this paper, a design of an integral augmented nonlinear optimal variable structure system(INOVSS) is presented for the prescribed output control of uncertain MIMO systems under persistent disturbances. This algorithm basically concerns removing the problems of the reaching phase and combining with the nonlinear optimal control theory. By means of an integral nonlinear sliding surface, the reaching phase is completely removed. The ideal sliding dynamics of the integral nonlinear sliding surface is obtained in the form of the nonlinear state equation and is designed by using the nonlinear optimal control theory, which means the design of the integral nonlinear sliding surface and equivalent control input. The homogeneous $2{\upsilon}(\kappa)$ form is defined in order to easily select the $2{\upsilon}$ or even $(\kappa)-form$ higher order nonlinear terms in the suggested sliding surface. The corresponding nonlinear control input is designed in order to generate the sliding mode on the predetermined transformed new surface by means of diagonalization method. As a result, the whole sliding output from a given initial state to origin is completely guaranteed against persistent disturbances. The prediction/predetermination of output is enable. Moreover, the better performance by the nonlinear sliding surface than that of the linear sliding surface can be obtained. Through an illustrative example, the usefulness of the algorithm is shown.

• Structural Engineering and Mechanics
• /
• v.61 no.3
• /
• pp.371-379
• /
• 2017

Modelling of a crack propagating through a finite element mesh under mixed mode conditions is of prime importance in fracture mechanics. In this paper, two crack growth criteria and the respective crack paths prediction in functionally graded materials (FGM) are compared. The maximum tangential stress criterion (${\sigma}_{\theta}-criterion$) and the minimum strain energy density criterion (S-criterion) are investigated using advanced finite element technique. Using Ansys Parametric Design Language (APDL), the variation continues in the material properties are incorporated into the model by specifying the material parameters at the centroid of each finite element. In this paper, the displacement extrapolation technique (DET) proposed for homogeneous materials is modified and investigated, to obtain the stress intensity factors (SIFs) at crack-tip in FGMs. Several examples are modeled to evaluate the accuracy and effectiveness of the combined procedure. The effect of the defects on the crack propagation in FGMs was highlighted.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.3 s.246
• /
• pp.249-259
• /
• 2006

Stress and displacement fields of a propagating Mode III crack in an orthotropic functionally gradient material (OFGM), which has (1) linear variation of shear modulus with a constant density, and (2) an exponential variation of shear modulus and density, are derived. The equations of motion in OFGM are developed and solution to the displacement and stress fields fer a propagating crack at constant speed though an asymptotic analysis. The stress terms associated with $\gamma^{-1/2}\;and\;\gamma^{0}$ are not affected by the FGM constant $\zeta$ which is nonhomogeneous parameter, only on the higher order terms, the influences of nonhomogeneity on the stress are explicitly brought out. When the FGM constant $\zeta\;is\;zero\;or\;\gamma{\rightarrow}0$, the fields for OFGM are almost same as the those for homogeneous orthotropic material. Using the stress components, the effects of nonhomogeneity on stress components are discussed.

• Earthquakes and Structures
• /
• v.15 no.4
• /
• pp.411-417
• /
• 2018

To solve the seismic response problem of a vertical floating roof tank with base isolation, the floating roof is assumed to experience homogeneous rigid circular plate vibration, where the wave height of the vibration is linearly distributed along the radius, starting from the theory of fluid velocity potential; the potential function of the liquid movement and the corresponding theoretical expression of the base shear, overturning the moment, are then established. According to the equivalent principle of the shear and moment, a simplified mechanical model of a base isolation tank with a swinging effect is established, along with a motion equation of a vertical storage tank isolation system that considers the swinging effect based on the energy principle. At the same time, taking a 150,000 m 3 large-scale storage tank as an example, a numerical analysis of the dampening effect was conducted using a vibration mode decomposition response spectrum method, and a comparative analysis with a simplified mechanical model with no swinging effect was applied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.195-195
• /
• 2010

In recent years, Anodic aluminum oxide(AAO) has become popular and attractive materials. It can be easily fabricated and self-organized pore structures. It has been widely used as a biosensor membrane, photonic crystal for optical circuit and template for nanotube growth etc. In previous papers, the theory was developed that AAO shows anisotropic optical properties, since it has anisotropic structure with numerous cylindrical pores. It gives rise to the anisotropy of the refractive index called as birefringence. It can be used as conventional polarizing elements with high efficiency and low cost. Therefore, we would like to compare the theory and experimental results in this study. One method which can measure effective refractive index of thin film is the prism coupling technique. It can give accurate results fast and simply. Furthermore, we can also measure separately the refractive index with different polarization using polarization of the laser (TE mode and TM mode). We calculated the effective refractive index with effective medium approximations (EMAs) by pore size in the SEM image. EMAs are physical models that describe the macroscopic system as the homogeneous and typical method of all mean field theories.

• Computational Structural Engineering
• /
• v.9 no.3
• /
• pp.209-216
• /
• 1996

The primary objective of this paper is to grasp many characteristics of buckling behavior of latticed spherical domes under various conditions. The Arc-Length Method proposed by E.Riks is used for the computation and evaluation of geometrically nonlinear fundamental equilibrium paths and bifurcation points. And the direction of the path after the bifurcation point is decided by means of Hosono's concept. Three different nonlinear stiffness matrices of the Slope-Deflection Method are derived for the system with rigid nodes and results of the numerical analysis are examined in regard to geometrical parameters such as slenderness ratio, half-open angle, boundary conditions, and various loading types. But in case of analytical model 2 (rigid node), the post-buckling path could not be surveyed because of Newton-Raphson iteration process being diversed on the critical point since many eigenvalues become zero simultaneously.

• The Research Journal of the Costume Culture
• /
• v.18 no.1
• /
• pp.177-189
• /
• 2010

The purpose of this study is to research the conspicuous consumption characteristic expressed in the modern fashion. The conspicuous consumptions are classified with 2 parts as follows as: 1. The motive of conspicuous consumption, 2. The effect of conspicuous consumption. And the motive of conspicuous consumption is 1) conspicuous consumption, 2) conformity consumption, 3) compensatory consumption. The effect of conspicuous consumption is 1) veblen effect, 2) bandwagon effect, 3) snob effect. The veblen effect is caused either by the belief that higher price means higher quality, or by the desire for conspicuous consumption to be seen as buying an expensive, prestige item. The bandwagon effect is people tend to follow the crowd without examining the merits of a particular thing. The snob effect refers to the desire to own unusual, expensive or unique goods. The conspicuous consumption has produced conflicting results of the homogeneous imitation and the different scarcity. Consequently conspicuous consumption characteristic expressed in the modern fashion refers to the conformable imitation and the different scarcity. The conformable imitation is pursuit of first lady look and imitation. The different scarcity refers to the desire to own exclusive or unique goods. The unique value is pursuit of limited edition and art mode.