• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.3
• /
• pp.430-435
• /
• 2012

This study was carried out to investigate the rheological effects of black garlic extracts on the bread dough. 0, 5, 10 and 15% of black garlic extracts were added in the bread flour. Falling number, RVA (Rapid visco analyser), farinograph and alveograph were analyzed. Falling number was lowered by increasing the amount of the extract added in the wheat flour. The pasting characteristics of the dough by RVA, value of pasting temperature, peak viscosity, holding strength, final viscosity, break down and set back were increased compared to the control. In the Farinograph analysis, the consistency and the water absorption ratio were elevated with the increase of the extract added. However, the rapid decrease of stability and the time to breakdown values were observed by increasing the extract addition amount compared to the control. However the mixing tolerance index (MTI) was rapidly increased as the amount of the extract addition was increased, and the highest farinogram quality number was observed in the control. Through the alveograph analysis, $P_{max}$ value was found to show the highest value in the control, while the L and G values were higher but W values was lowered in the dough with added 15% black garlic extract. As a result of the analysis, there was no significant bad effect until 5% of black garlic extracts was added to the bread dough.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.1
• /
• pp.55-64
• /
• 2000

Culture maturity assessment can be used to control fruiting body flush timing. Culture maturity of sawdust-based substrate was evaluated by using oak mushroom, (Lentinula edodes (Berk.) Pegler). The influence of substrate water potential (${\psi}$) on the growth and fruiting of three genotypes of L. edodes was also investigated. Glucosamine content revealed a peak at the fruiting body senescent stage. Glucosamine increased steadily to the sporophore senescent stage, and sharply declined at crop treatment. Lipid phosphate and ergosterol contents peaked at pinning and button break stages, respectively. Therefore lipid phosphate and ergosterol contents would be considered as the convenient measurement for judging culture maturity and fruiting potentials. The substrate pH values before inoculation and on the fruiting stage were varied from 6.3 to 4.0. This pH changes were detected as changes in color from bluish purple to yellow by direct bromphenol blue(BPB) spraying, and shown a good correlation with fruit body yield of the 1 st flush. Concerning water potential of the cultures, a slight reduction of water potential, -0.5MPa, stimulated mycelial and colony growths on liquid, agar and sawdust-based substrates. The water potential of well-colonized matured substrate was -0.7MPa and -4.0MPa, before and after the fruiting, respectively. Excellent water providing capacity (higher ${\psi}$) is expected to well-matured cultures with a high density of mycelial colonization. Also, the substrate water potential significantly affected by the interaction between genotypes and spawn run time.

• Korean Journal of Food Science and Technology
• /
• v.23 no.2
• /
• pp.188-191
• /
• 1991

A study was carried out to investigate the control effect of sodium and potassium phosphates, sodium citrate and three different salts mixtures on kimchi fermentation when they were added into half-fermented kimchi in the concentration range of $0.001{\sim}0.01\;M$. The salts mixtures added were sodium phosphates mixture(CA-A), addition of $NaNO_2$, Ca-EDTA and BHA to CA-A(CA-B) and substitution of BHA with sodium citrate in CA-B. The results showed that sodium phosphates and sodium citrate significantly inhibited the kimchi fermentation while potassium phosphate had little effect. The order of control effect was $Na_3PO_4-Na_2HPO_4-sodium\;citrate-NaH_2PO_4-K_2HPO_4-KH_2PO_4$. Among the salts mixtures, CA-A showed the most reducing effect in the fermentation rate followed by CA-C and CA-A. The mixture of CA-C could extend the time of holding pH $4.2{\sim}4.4$ by approximately 6 times at $4{\sim}25^{\circ}C$ when it was compared to control. The microbial growth study of total and Leuconostoc mesenteroides also showed a very significant decrease in their numbers.

• Food Science of Animal Resources
• /
• v.26 no.1
• /
• pp.28-36
• /
• 2006

This study was carried out to investigate the changes in physicochemical, microbiological and sensory properties on vacuum packaged Yakibuda products for Export during storage at $4{\pm}1^{\circ}C$ for 40 days. Yakibuda, Japanese favorite meat product, were produced with three different pork cuts or tenderloin (T1), loin (T2) and ham (T3). The pH of all produce was tend to increased with increase in storage period. After 40 days of storage, pH of T2 was significantly (p<0.05) higher compared to other treatments. TBARS and VBN values of all treatments were increased with increased storage period. The water holding capacity ranged $81.41{\sim}92.20%$ in T1, $81.13{\sim}94.51%$ in T2 and $82.93{\sim}87.50%$ in T3. The shear force of T3 was higher than that of other treatments during whole storage time. The number of microorganism (Total plate counts, Escherichia coli, Lactobacilli spp.) were below 3.0 $log_{10}CFU/cm^2$ during the whole storage period. In sensory evaluation, the score of overall acceptability were above 5.5 point in all products. The storage properties of vacuum packaged Yakibuda could be maintained for 40 days at $4{\pm}1^{\circ}C$ storage temperature.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.283-292
• /
• 1996

This study was performed to determine the physical properties of rice hull and straw which could be used for an optimum design and operation of the handling facilities for these rice crop by-products. The properties measured were kinetic friction coefficient , bulk density, and dynamic and static angle of repose. Rice hulls with moisture content of 13% and 21% were used throughout the test while rice straws of 10% and 16% moisture were chopped into 10mm length and used for the test. Friction coefficient was calculated from the horizontal traction forces measurement when a container holding the mass of rice hull and straw was pulled over mild steel. PVC, stainless steel, and galvanized steel surface by a universal testing machine. Bulk density was measured by an apparatus consisting of filling fundel and a receiving vessel. Dynamic angle of repose which is the angle at which the material will stand when piled was calculated from the photos of bulk samples after they were flowed by gravity and accumulated on a circular surface. Static angle of repose which is the angle between the horizontal and the sloping side of the material left in the container when discharging was also measured in the similar way. Results and conclusions from this study are summarized as follows . 1. Kinetic friction coefficient of both rice hull and straw were in the range of 0.26 -0.52 and increased with the moisture content. The magnitude of friction increased in the order of galvanized steel, stainless steel, PVC ,and mild steel. 2. Bulk densities of rice hull decreased while those of rice straw increased with moisture content increase . Average bulk densities of rice hull and straw were 96.8 and 74.7kg/㎥, respectively. 3. Average dynamic angle of repose for rice straw was 32.6$^{\circ}$ and those for 13% and 21% moisture rice hull were 38.9$^{\circ}$ and 44.9$^{\circ}$ , respectively. 4. Static angles of repose for both rice hull and straw showed increase with the moisture content. The values were 75.2\ulcorner and 80.2$^{\circ}$ for 13% and 21% moisture rice hull, respectively. Rice straws having 10% and 16% moisture content showed 87.3% and 89.2$^{\circ}$ static angle of repose, respectively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.1
• /
• pp.73-83
• /
• 1997

Most of the materials used in various industrial fields and also in our daily life are multi-component materials or composite materials, and it is well known that there are many cases where adhesion between the constituents within the bonded systems plays an important role. There are various types of performance evaluation tests for the bonded materials, among which tests for evaluating the bond performance under various conditions may be regarded as the most interesting ones for those engaged in work related to adhesion. I have studied on the mechanism of adhesion form the rheological standpoint with my colleagues, including some students from Korea, and I am very happy to be able to have a talk on some of our research works. In Japan, the so-called "adhesives" are usually classified into two categories;adhesives and pressure sensitive adhesives (PSA). Adhesives are the materials which solidify after bonding and are after used as the structural adhesives because the adhesive strength is comparatively strong. On the other hand, the pressure sensitive adhesives never solidify and are used as PSA tapes, labels or decals. About the adhesives, we have examined the dependence of adhesive strength(shear, tensile, peel) upon both temperature and rate of deformation, and found out some empirical rules which are applicable to most of the adhesive systems. We have also developed a simplified theory of adhesion, which is deseribed in terms of mechanical equivalent mode1 and a few failure criteria. Although some of the common rules can be accounted for according to this theory, it must be pointed out that a fracture mechanical approach ms inevitable especially in the region where the meehanical relaxation time of the adhesive is extremely large [W. W. Lim and H. Mizumachi]. About the pressure sensitive adhesives, we have studied on the PSA performance (peel, tack, holding power) as a function of both the viscoelastic properties and surface chemical properties of the materials, and found out some rules, and again we have developed a theory which deseribes the mechanism. And in addition, we have studied on the miscibility between linear polymers and oligomers, because PSA is generally manufactured by blending gums and tackifier resins. Many phase diagrams have been found and some of them have been analyzed on thermodynamic basis, and it became evident that the miscibility is a very important factor in PSA [H. J. Kin and H. Mizumachi]. In this presentation, I want to emphasize the fact that the adhesion performance is closely related to the structure/property of the adhesives.adhesives.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.4
• /
• pp.249-255
• /
• 2017

BACKGROUND: Globally, mulberry (Morus sp.) is exploited for feeding leaf to silkworms in order to obtain silk fiber or for animal feedstock production. Also, mulberry fruit is known to a by-product that was produced from mulberry tree after harvesting leaves for silkworm rearing, as a yield and consumption of mulberry fruit was increased, it has been fixing to a newincome crop. Mulberry leaves and fruits are used for the health benefits of human beings. Mulberry contains various bioactive components, such as alkaloids and flavonoids. Mulberry flavonoids are an important part of the diet because of their effects on human nutrition. The flavonoids in mulberry leaf and fruit of 'Suhyang'(Morus alba L.) were determined. METHODS AND RESULTS: Flavonoids for mulberry leaf and fruit of 'Suhyang' were analysed using ultrahigh performance liquid chromatography coupled with diode array detection and quadrupole time-of-flight mass spectrometry (UPLC-DAD-QTOF/MS)technique. An UPLC-DAD-QTOF/MS system was used, and identification of mulberry leaves constituents was carried out on the basis of the complementary information obtained from LC spectra, MS ions, and MS/MS fragments. The mulberry leaf (16 flavonoids) and fruit (9 flavonoids) were isolated and analyzed from Suhyang using UPLC-DAD-QTOF/MS chromatogram. To the best of our knowledge, Quercetin 3-O-(6"-O-malonyl) glucoside and quercetin 3-O-rutinoside (rutin) was detected on the highest content in leaf and fruit, respectively and further research will be devoted to evaluate their biological activity. CONCLUSION: Obtaining information about the concentration of functional materials in mulberry leaves could contribute to the development and promotion of processed, functional products and offer possible industrial use of 'Suhyang', holding promises to enhance the overall profitability of sericulture.

• Food Science of Animal Resources
• /
• v.36 no.1
• /
• pp.68-76
• /
• 2016

This study was conducted to investigate the meat quality and sensory properties of 12 major cuts from 10 Hanwoo bulls (25-32 mon of age) after they were aged at 2℃ for 0, 7, 14, and 21 d. Protein content (%) was between 19.17 and 22.50%. Intramuscular fat content ranged from 2.79 to 8.39%. The collagen content of the chuck roll, chuck tender, and short plate muscles was higher (1.97-2.04%) than that of the striploin muscles (1.48%) (p<0.05). CIE lightness (L*) values increased with an increase in aging days for tenderloin, loin, chuck roll, oyster blade, short plate, top sirloin, and eye of round muscles (p<0.05). Most muscles, except the short plate, showed no significant changes in redness CIE (a*) and yellowness (b*) color values during aging. The tenderloin, loin, and striploin showed significantly higher water holding capacity (58.60-62.06%) than that of chuck roll and short plate (53.86-57.07%) muscles (p<0.05). The Warner-Bratzler shear force values of most muscles decreased significantly as the aging period increased (p<0.05), exception the tenderloin. The chuck tender muscles showed the highest cooking loss, whereas tenderloin muscle showed the lowest (p<0.05). The tenderloin muscle had the longest sarcomere length (SL) (3.67-3.86 μm) and the bottom round muscle had the shortest SL (2.21-2.35 μm) (p<0.05). In the sensory evaluation, tenderness and overall-likeness scores of most muscles increased with increase in aging days. The tenderloin and oyster blade showed relatively higher tenderness and overall-likeness values than did the other muscles during the aging period. No significant differences were noted in juiciness and flavor-likeness scores among muscles and aging days.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.4
• /
• pp.746-754
• /
• 1996

The purpose of this study was to evaluate the fracture strength of porcelain laminate veneer with various lingual extention length when incisal restoring. Sixty recently extracted, intact maxillary incisors were used and stored in a physiologic saline solution from the time of extraction. Seating form was preparation at the labial surface of each tooth with a water-cooled round diamond bur. Standard block was formed with 32 gauge and 24 gauge wax at tooth labial and lingual surface. Lingual extention length differed according to each group. (group I : 0.5mm, group II : 1 mm, group III : 2mm, group IV : 0mm) All tooth specimens were impressioned with examix(GC Inc., Japan). Refractory cast were maked with refractory die material(Ceramco Inc., U.S.A.) Laminate porcelain (Ceramco II Veneer porcelain, Ceramco Inc., U.S.A.) was condensed in refractory die cast and baked according to the manufacturer's recommendations. Each surface was contoured with low speed diamond bur according to guide block. All porcelain specimens were sandblasted and ultrasonically cleaned in distlled water for 3 minutes. Then, all porcelain specimen were etched with 8% hydrofluoric acid for 5 minutes. Sixty specimens were bonded with composite resin cement(Choice Porcelain Veneer System, Bisco Inc., U.S.A.) according to manufacture's directions. The fracture loads of the specimen were measured by Instron universal testing machine. The mean values of fracture loads for the groups were statistically compared by Duncan's multiful range test. The result were as follows : Mean fracture strengths of each group were 86.95Mpa in no lingual extention group, 44.98Mpa in 0.5mm lingual extention group, 27.47Mpa in 1mm lingual extention group, 19.61Mpa in 2mm lingual extention group. There was a statistically significant difference between all group(p<0.01).

• Food Science of Animal Resources
• /
• v.23 no.3
• /
• pp.221-226
• /
• 2003

This study investigated the effect of different electrical stunning methods on pH, water holding capacity(WHC), cooking loss(CL), meat color and blood spot rate in broilers. One-hundred and forty broiler chickens were slaughtered by 50, 65 and 90 voltage with the same electrical frequency(255 Hz) and stunning time(5 sec) in commercial abattoir. The ultimate pH of leg muscle and WHC of breast muscle decreased with increasing the stunning voltage. However, there were no significant differences in ultimate pH, WHC and CL of breast muscle, and ultimate pH of leg muscle. Lightness(L*) and yellowness(b*) values of leg muscle stunned with 90V, 255 Hz, 5 sec were higher than those stunned with 50V, 255 Hz for 5 sec(p<0.05). But there were no significant differences in color value on skin, breast and wing muscle. Our experiments showed that change of stunning voltage affected some broiler meat quality parameters. However, further research is necessary to examine the effects of stunning condition on broiler meat quality.