• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.128-134
• /
• 2005

In order to fabricate the aluminum alloys with good drawability, the textures evolution of the AA5182 sheets after rolling and annealing was studied. The measurement of the deformation textures was carried out for the sheets which were cold rolled with high reduction ratio by using the symmetric roll. In addition, the change of the recrystallization texture was investigated after heat-treatments of the rolled sheets with various heat treatment conditions. Rolling without lubrication and subsequent annealing led to the formation of favorable $rot-C_{ND}\;\{001\}<110>\;and\;{\gamma}-fiber ND//<111>$ textures in AA5182 sheets. From the results, the ${\gamma}$-fiber ND//<111> component well evolved during rolling at highest reduction ratio (over $90\%$, l/d parameter of 6.77). Among shear deformation textures, the ${\gamma}$-fiber ND//<111> was not rotated in holding time of $180\~7,200$ seconds at $350^{\circ}C$. The Monte-Carlo technique was used and could be representatively simulated these textures evolution during recrystallization.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.2
• /
• pp.73-79
• /
• 2001

This paper describes the simple single phase air-conditioner of power factor correction (PFC) circuit. By adopting PFC in the rectifier, we can reduce harmonic into power line, improve the efficiency and lower the total system cost compared to conventional inviter only. Also, system performance is improved by stabilizing the output voltage of PFC. To improve the current waveform of diode rectifiers, we propose a new operating principle for the voltage diode rectifiers. A circuit design method is shown by experimentation and confirmed simulation. It explained that compared conventional pulse-width modulated (PWM) inverter with half pulse-width modulated (HPWM) inverter HPWM inverter. Proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.496-501
• /
• 2007

In order to enhance sintering characteristics on the $ZnO-Pr_6O_{11}$ based multilayer chip varistors (MLVs), a response surface analysis using central composite design method were carried out. As a result, varistor voltage($V_{1mA}$), nonlinear coefficient ($\alpha$), leakage current ($I_L$) and capacitance (C) were considered to be mainly affected by sintered temperature and holding time. MLVs sintered at $1200^{\circ}C$ and above $1200^{\circ}C$ revealed poor electrical characteristics, possibly due to the reaction between electrode materials(Pd) and $ZnO-Pr_6O_{11}$ based ceramics. On the sintering temperature range $1150{\sim}1175^{\circ}C$, nonlinear coefficient ($\alpha$) and leakage current ($I_L$) were shown to be $60{\sim}69$ and below $0.3{\mu}A$, respectively. In particular, MLVs sintered at $1175^{\circ}C$, 1.5 hr and $2^{\circ}C/hr$ (cooling speed) showed stable ESD(Electrical Static Discharge) characteristics under the condition of 10 times at 8 Kv with deviation varistor voltage, and deviation nonlinear coefficient were 0.3% and 0.33% (at positive), 0.55% (at negative), respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1139-1145
• /
• 1998

In this paper, to fabricate a superconducting fault current limiter(FCL) of thick film type, $YBa_2Cu_3O_X superconducting thick films were fabricated by surface diffusion process using the screen printing method. Powder mixture of $3BaCuO_2$+2CuO was screen printed on $Y_2BaCuO_5$(d=15mm). And critical current densities of the thick films were observed as the sintering temperature(92$0^{\circ}C$~95$0^{\circ}C$) and holding time(2h~10h). Based on experimental data, the thick films for superconducting FCL were sintered at $940^{\circ}C$ in 2 hours. The superconducting FCL with a current limiting area of 1mm wide and 66mm long was prepared on $Y_2BaCuO_5$ substrate. To measure the characterization of the fabricated FCL, an alternating voltage (60Hz) was applied to the FCL in 77K liquid nitrogen. At an applied voltage of 4V, the FCL was limited from 20A into 0.6A not farther than 0.5ms.

• Journal of Powder Materials
• /
• v.17 no.6
• /
• pp.494-498
• /
• 2010

The p-type thermoelectric compounds of $Bi_2Te_3$ based doped with 3wt% Te were fabricated by a combination of rapid solidification and spark plasma sintering (SPS) process. The effect of holding time during spark plasma sintering (SPS) on the microstructure and thermoelectric properties were investigated using scanning electron microscope (SEM), X-ray diffraction (XRD) and thermoelectric properties. The powders as solidified consisted of homogeneous thermoelectric phases. The thermoelectric figure of merit measured to be maximum ($3.41{\times}10^{-3}/K$) at the SPS temperature of $430^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.20 no.1
• /
• pp.38-45
• /
• 2000

The remelting for recycling or thin aluminum scrap, such as aluminum chip generally involves melting of these pieces submerged in molten salt flux. In this study, the effects of salt flux compositions and alloying elements on the aluminum dropletscoalescence and oxide film removal were studied in 99.8%Al, Al-1.01%Cu, Al-1.03%Si, and Al-1.38%Mg alloys as a function of holding time at $740^{\circ}C$ Salt fluxes based on NaCl-KCl(1:1) with addition of 5wt.% fluorides(NaF, $Na_3AlF_6$, $CaF_2$) or 5 wt.% chloride($MgCl_2$, $AlCl_3$) were used. The experimental results show that NaCl-KCl(1:1) with addition of 5 wt.% fluorides exhibits better coalescence ability than that with chlorides. The oxide film is not removed by NaCl-KCl(1:1) with addition of 5 wt.%chlorides, while it is removed by NaCl-KCl(1:1) with addition of 5 wt.% fluorides. The aluminum droplets coalescence and oxide film removal by salt fluxes are related to interfacial tension tension between metal and salt flux.

• Journal of Korea Foundry Society
• /
• v.19 no.5
• /
• pp.427-432
• /
• 1999

Most investment castings contain some porosities and microcavities. In this study, we investigated the elimination trends of various internal defects in IN738LC investment castings for industrial gas turbine blade by hot isostatic pressing. The results showed that cylindrical defects which are under $0.6mm{\Phi}{\times}7mm$ size are mostly eliminated and aspect ratio of defects is more sensitive factor than their cross section shape in removing these defects. Increasing hot isostatic pressure and holding time doesn't affect the elimination trend of cylindrical defects over $0.6mm{\Phi}{\times}7mm$ size because first step(plastic deformation) of HIP densification doesn't occur under these HIPping conditions.

• Korean Journal of Materials Research
• /
• v.16 no.12
• /
• pp.743-746
• /
• 2006

ZTA tubes were prepared by centrifugal casting and sintered at $1600^{\circ}C$ for 2 hrs. The ZTA tubes were machined into specimens of $3{\times}4{\times}40$ mm. Molten Soda lime glass (SLG) was penetrated into the surface of ZTA at an optimized condition of $1500^{\circ}C$ for the holding time of 5 h and furnace cooled. The extra glass on the surface was removed using a resin bonded diamond wheel. The glass penetrated samples were tested for their flexural strength using four point bend test. Vickers Indentation cracks were made on the glass penetrated surface at different loads of 9.8 N, 49 N, 98 N and 196 N. The residual compression on the surface enhanced the flexural strength and crack arrest behaviour remarkably. This was attributed to the thermoelastic mismatch between the glass and ZTA matrix during cooling.

• Korean Journal of Materials Research
• /
• v.21 no.11
• /
• pp.623-627
• /
• 2011

This is a study on the distribution of acoustic emission parameters during a burst test for a type-II CNG vehicle fuel tank. A resonant AE sensor with a central frequency of 150 kHz was attached to the composite materials in the center of the fuel tank. The pressure was increased from 30 to 100% of the expected burst pressure and was maintained for 10 minutes at each level. Damage at 70% of expected burst pressure occurred by various damage mechanisms including fiber breakage and delamination, while that of below 60% only occurred by matrix crack initiation and growth. The count, duration and rise time of the AE signal at 60% of the expected burst pressure are distributed below 500, 5000 ${\mu}s$ and 300 ${\mu}s$, respectively. Then, at above 70% they increased with pressure by superimposing of individual AE signal generated at a nearby place. These results confirmed that the analysis of the distribution of AE parameters is an effective tool for estimating damage of a CNG fuel tank.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.229-235
• /
• 2014

In this paper, the effects of precipitates and Mn-solute atoms on the recrystallization behavior of an Al-Mn alloy was studied using micro-Vickers hardness, electrical conductivity measurements and optical microscopy. Various thermo-mechanical processes were designed to investigate the different morphologies, and the solute concentration, of Mn in the matrix. The results indicate that the recrystallization temperature, $T_R$ and time, $t_R$, are influenced by the amount of M-solute atoms in the matrix, and that the recrystallization microstructure is influenced by the amount of precipitates. Recrystallization in the Slow-Cooling specimen was rapid due to its low concentration of Mn-solute atoms, and the crystal-grain size was the smallest due to finely distributed precipitates. However, in the case of the No-Holding specimen, elongated grains were observed at the low annealing temperature and the largest recrystallized grains were observed at the high annealing temperatures (compared with Slow-Cooling and Base specimens) due to the high Mn-solute atoms in the matrix.