• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.1
• /
• pp.49-61
• /
• 2015

This is the second of two companion papers that describe the performance assessment for flexible rockfall protection systems. Described in a companion paper is the criteria to assess the performance of flexible rockfall protection systems. In this study the performance assessment of domestic rockfall protection fences was implemented using the criteria suggested in the companion paper. It was investigated that the rockfall protection fences for express highways performed well to resist the rockfall energy of 50kJ and the deformed rockfall protection fences right after impacting would not obstruct the vehicle traffic. However, to dissipate the rockfall energy of 50kJ with the level of European standards constantly, the spacing of wireropes was adjusted to be 200mm up to the 8th wirerope from the bottom and spacing-maintainers should be extended to the 8th wirerope. It was figured out that the rockfall protection fences for general highways were required to install spacing-maintainers as those for express highways because they, which did not have spacing-maintenance members, were very prone to the penetration of rockfall even for the very small rockfall impact energies.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.6
• /
• pp.48-55
• /
• 2009

The feedback interference channels are those made through the multipaths that are built by moving and stationary objects around transmit and receive antennas mounted at the same point. This paper describes the method to measure the feedback interference channels in the rural regions and sides of highways and the analysis on channel characteristic parameters. Using the measured samples, we estimated scattering functions, delay power spectra, and Doppler power spectra, and we analyzed the channels using eight parameters including coherence bandwidth, coherence time, maximum excess delay, average excess delay, rms delay spread, Doppler shift, Doppler spread, and spread factor, and delay and Doppler cumulative distributions. Even though many observations are made, note that the feedback signals of high Doppler frequencies and large energy are observed in the sides of highways due to high speed vehicles while low Doppler frequencies occurred in the rural region due to rare traffic.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.143-150
• /
• 2015

PURPOSES : The authors set out to estimate the related carbon emissions, energy use, and costs of the national freeways and highways in Korea. To achieve this goal, a macro-level methodology for estimating those amounts by road type, road structure type, and road life cycle was developed. METHODS : The carbon emissions, energy use, and costs associated with roads vary according to the road type, road structure type, and road life cycle. Therefore, in this study, the road type, road structure type, and road life cycle were classified into two or three categories based on criteria determined by the authors. The unit amounts of carbon emissions and energy use per unit road length by classification were estimated using data gathered from actual road samples. The unit amounts of cost per unit road length by classification were acquired from the standard cost values provided in the 2013 road business manual. The total carbon emissions, energy use, and cost of the national freeways and highways were calculated by multiplying the road length by the corresponding unit amounts. RESULTS: The total carbon emissions, energy use, and costs associated with the national freeways and highways in Korea were estimated by applying the estimated unit amounts and the developed method. CONCLUSIONS: The developed method can be employed in the road planning and design stage when decision makers need to consider the impact of road construction from an environmental and economic point of view.

• Journal of Veterinary Clinics
• /
• v.31 no.4
• /
• pp.282-287
• /
• 2014

The negative impacts of roads on wildlife mortality have been well documented, and one of the most significant impact is wildlife-vehicle collisions (WVCs) in most countries throughout the world. While road impacts on wildlife are a truly global concern with a large socio-economic cost, few researches in Korea have been quantified road-kill occurrence on highways or identified extensively seasonal and geographic patterns of this phenomenon. Therefore, we analyzed highway mortality of wild mammals in Korea using database from five years of nation-wide data on WVCs, and estimated road-kill density by standardizing on per km and per $10^3$ vehicle basis. During 2008 through 2012, a total of 10,940 wildlifes were reported killed on highways, with an average of 2,188 cases per year. There were 2,376 road-kills in 2012, and this equates to 0.01 road-kills per km per week or one road-kill every 88.5 km per week. For time of day, road-kills occurred more frequently in the early morning (05:00-08:00, 38.3%), and day of week did not have a significant influence in any individual year. The road-kill was highest in the spring (March- May, 33.0%) and least in the winter (December-February, 16.1%), and the most frequently killed native species were of Korean water deer (79.7%), raccoon dog (12.7%), Korean hare (3.1%), and leopard cat (1.2%). The overall standardized kill-rate (number/10 km/1,000 vehicles/month) in 2012 was 0.057 with highest on Dangjinyeongdeok highway (0.476), followed by Yeongdong (0.274), Sooncheonwanju (0.233), Iksanpohang (0.187), and Joongang (0.150). This study highlights that the frequency of WVCs are prevalent throughout the highways in Korea. Further work is needed to determine whether such a level of mortality is sustainable from an ecological point of view.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.2
• /
• pp.13-22
• /
• 2017

The present study proposes a new methodology for predicting the demand for truck rest areas beside national highways. Previous demand forecasting methods were reviewed first in order to complement them with additional items. The results of the study are as follows. In the demand forecasting process, the primary task is to divide parking demands of trucks into short-term parking and long-term parking. Since short-term and long-term parking vary in utilization, congestion, and turnover rate, different influence factors should be considered according to parking time. Furthermore, the demand characteristics of rest and convenience facilities need to be reflected as well, because they in turn affect the demand for truck rest areas. In sum, the demand forecasting process for destination-type truck rest areas on national highways requires more attention than that for truck rest areas on expressways, and possible influences of various factors should be examined in this process.

• Journal of Korea Spatial Information System Society
• /
• v.9 no.1
• /
• pp.79-90
• /
• 2007

In this paper we proposed and implemented an incident detection model which combines fuzzy algorithm and traffic pattern in order to enhance the efficiency of incident detection for the highways with lamps. Most of the existing algorithms dealt with highways without lamps and can not be used for detecting incidents in the highways with lamps. The data used for model building are traffic volume, occupancy, and speed data. They have been collected by a loop sensor at 5 minutes interval at a point in the Internal Circular Highway of Seoul for the period of 3 months. In this model, the three parameters collected by sensor were fuzzified and combined with the daily traffic pattern of the link. The test of efficiency of the propsed model was performed by comparing the result of proposed model with traditional APID algorithm and fuzzy algorithm without the pattern data respectively. The result showed significant amount of improvement in reducing the false incident detection rate by 18%.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.127-134
• /
• 2009

This study was performed to establish the process mean which is statistically satisfying the critical limit of deformation strength $(S_D)$, which is found to reflect rutting characteristics of asphalt mixture relatively well. The process means were determined using the critical $S_D$ values (3MPa for local highway and 4MPa for arterial highways), which were obtained from correlation analysis of APA and $S_D$ test data of actual highway projects, and coefficient of variation of 32 combinations of domestic mixtures. The process means of 3.2 MPa for local highway and 4.25 MPa for arterial highways were suggested when using 3 specimens (diameter of 100mm). However, since these values are based on the loading speed of 30mm/min, the higher values, 3.5 MPa for local highway and 4.5 MPa for arterial highways, were suggested, respectively, if the loading speed of 50mm/min is applied using the old Marshall machine, which should give higher test values.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.75-82
• /
• 2007

This study was performed to investigate impacts of truck lane restrictions on multilane highways on traffic flow variables such as average speed, the frequency of lane changes, and change in traffic volume and also to verify whether or not different lane restriction scenarios were proper. Two types of hypothetical highway networks and OD demands were developed for traffic simulation models in order to conduct the experimental study. Three types of scenarios were also developed according to the number of restricted lanes for trucks. The PARAMICS microscopic traffic simulation software package was used as the primary analytical tool. Statistical analysis was conducted with simulation outputs. Results showed that truck lane restrictions may lead to positive impacts on traffic flow on multilane highways. In addition, this study demonstrated that the number of restricted lanes can be very an important factor to lead successful implementation of truck lane restrictions.

• Smart Structures and Systems
• /
• v.15 no.1
• /
• pp.99-117
• /
• 2015

The Stonecutters Bridge (SCB) in Hong Kong is the third-longest cable-stayed bridge in the world with a main span stretching 1,018 m between two 298 m high single-leg tapering composite towers. A Wind and Structural Health Monitoring System (WASHMS) is being implemented on SCB by the Highways Department of The Hong Kong SAR Government, and the SCB-WASHMS is composed of more than 1,300 sensors in 15 types. In order to establish a linkage between structural health monitoring and maintenance management, a Structural Health Rating System (SHRS) with relevant rating tools and indices is devised. On the basis of a 3D space frame finite element model (FEM) of SCB and model updating, this paper presents the development of an SHR-oriented 3D multi-scale FEM for the purpose of load-resistance analysis and damage evaluation in structural element level, including modeling, refinement and validation of the multi-scale FEM. The refined 3D structural segments at deck and towers are established in critical segment positions corresponding to maximum cable forces. The components in the critical segment region are modeled as a full 3D FEM and fitted into the 3D space frame FEM. The boundary conditions between beam and shell elements are performed conforming to equivalent stiffness, effective mass and compatibility of deformation. The 3D multi-scale FEM is verified by the in-situ measured dynamic characteristics and static response. A good agreement between the FEM and measurement results indicates that the 3D multi-scale FEM is precise and efficient for WASHMS and SHRS of SCB. In addition, stress distribution and concentration of the critical segments in the 3D multi-scale FEM under temperature loads, static wind loads and equivalent seismic loads are investigated. Stress concentration elements under equivalent seismic loads exist in the anchor zone in steel/concrete beam and the anchor plate edge in steel anchor box of the towers.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.4
• /
• pp.85-91
• /
• 2021

Some sections of the highway are closed due to disasters and accidents. In this situation, it analyzes what kind of situation occurs due to functional failure in the highway network. The domestic highway network can be expressed as a graph. Blocking some sections of the highway can turn into a national disaster. In this paper, we analyze the robustness of the domestic highway network. The robustness of expressways refers to the degree to which the traffic conditions of the domestic expressway network deteriorate due to the blockage of some sections. The greater the robustness, the smaller the effect of some blocking appears. This study is used to evaluate the congestion level of one section of the transportation network, and a value obtained by dividing the section traffic volume (V) by the section traffic volume (C) is used. This study analyzes the robustness of highways by using the actual traffic volume data of the departure and arrival points of domestic highways, and analyzes the changes in traffic volume due to partial blockage through experimental calculations. Although this analysis cannot reflect the exact reality of domestic highways, it is judged to be sufficient for the purpose of confirming the basic robustness of the overall network.