• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(I)
• /
• pp.440-445
• /
• 2002

In this paper, traction system for urban transit maglev system is proposed. Using vector control strategy to control magnitude and frequency of output voltage transiently is general. But in case of traction system for railway vehicle, it is impossible that adapt vector control because there is one-pulse mode in a high speed region. So this paper proposes the control strategy using vector control in a low speed region and slip frequency control in a high speed region. And also proposes overmodulation method that makes to change in one-pulse mode softly. The performance of traction system will be verified by simulation results using ACSL.

• 한국철도학회논문집
• /
• 제6권3호
• /
• pp.149-155
• /
• 2003

The development of railway vehicles involves the proper selection of design parameters not only to achieve high speed but also to reduce the vibration of the train. In this study an analytical model of a freight car is developed to find the critical speed. The freight car can generate the snake motion of the lateral and yawing motion of the car body, the bogie, and the wheelset. Numerical analysis for the nonlinear equation motions with 17 degrees of freedom showed the running stability and critical speed due to the snake motion. Also, the vibration modes of the freight car was calculated using ADAMS/RAIL, which showed that the critical speed have the yawing modes of the car body and the bogie. Finally this paper shows that the snake motion of the vehicle can be controlled with the modifications of the design parameters.

• 한국철도학회논문집
• /
• 제17권1호
• /
• pp.28-34
• /
• 2014

본 논문에서는 레일형 초고속 열차의 개념 설계안을 제안하고 동역학 해석을 통해 주행 동특성을 예측하고자 한다. 초고속 열차에는 단일 윤축세트가 포함된 새로운 형태의 대차가 적용되었으며, 기존의 일체형 차축 대신 독립차륜이 적용되었다. 초고속 열차의 동특성을 파악하기 위하여 먼저, 차량에 대한 동역학 수치해석모델을 개발하고 고유치 해석을 통해 해석 모델의 기본적인 타당성을 검증하였다. 또한, 임계속도 해석을 통하여 기존 고속철도 HEMU-430X 차량에 비해 향상된 성능을 확인하였으며, 7000R 곡선선로에서 550km/h 주행해석을 통하여 횡압, 탈선계수 등을 예측하고 초고속 열차 개념 설계안의 적용 가능성을 파악하였다.

• 한국정밀공학회지
• /
• 제34권3호
• /
• pp.205-210
• /
• 2017

Critical speed analysis was conducted for a active steering bogie prototype, developed to improve the curving performance of railway vehicles. The critical speed for the design concept was about 169.2k m/h. To validate the analysis result, we performed a critical speed test for the prototype bogie using a roller-rig tester. The test results showed that the critical speed for the prototype bogie was about 165 km/h. From the analysis and test results, The critical speed for the prototype bogie was determined to be 165 km/h. Considering the maximum operating speed of the test vehicle is 100 km/h, the prototype bogie is considered stable.

• 한국산학기술학회논문지
• /
• 제21권12호
• /
• pp.880-887
• /
• 2020

본 연구는 고속열차가 개활지와 터널을 운행할 때, 풍압과 교행 등에 의한 외력이 차량에 가해질 때 고속열차의 주행안정성에 대해 고찰하기 위하여 진행되었다. 고속열차 교행에 의한 외력이 없을 때, 400 km/h 속도로 주행 시 8량 1편성의 고속열차의 주행안정성을 검토한 결과 윤중 감소량, 횡압, 탈선계수는 국내 법규인 고속철도차량 기술기준의 주행 안전 부분을 만족하였다. 선로중심 간격 4.6 m일 경우 터널 내, 개활지 강풍이 없을 때 고속열차 교행에 의한 외력의 영향은 차체의 횡가속도에 조금 영향을 주나 윤중 감소율, 횡압, 탈선계수에는 크게 영향이 없고, 고속철도차량 기술 기준에서 허용하는 기준치 이내였다. 선로중심 간격이 4.6~5.0 m이고, 열차가 400 km/h로 주행 시 개활지 강풍 20 m/s 및 교행에 의한 외력이 있을 때 윤중 감소율, 횡압 및 탈선계수는 허용치 이내이고, 강풍 30 m/s 및 교행에 의한 외력이 있을 때 윤중 감소율 및 횡압은 허용치를 초과하고, 탈선계수는 허용치 이내였다. 이 결과로 400 km/h급 고속열차는 풍속이 20 m/s 정도까지 안전하게 운행할 수 있으며, 풍속이 30 m/s에서는 감속 운행이 이루어져야 할 것으로 예측되었다.

• 전기학회논문지
• /
• 제62권12호
• /
• pp.1820-1823
• /
• 2013

An overhead catenary system is the one of the main subjects for increasing speed in electric railway. When a vehicle increases the speed over 350km/h, vibrations and wave propagation reflections occur severely. Therefore, the system suitable for the speed are needed. A wave propagation speed of contact wire is the main criteria to determine the tension for the system. Therefore, a train speed is restricted below 70% of wave propagation speed of it in European railway code. In this study, we measured a strain and uplift of contact wire while HEMU-430X tain is operated for the speed-up trial test in Kyungbu high-speed railway. The measured strain and uplift are analyzed with wave propagation speed according to the speed-up. The more a train speed reaches to a propagation speed, the more measured strain is high. Through the study, an experimental approach is performed about the code which a train speed is restricted below 70% of wave propagation speed of it.

• 한국분무공학회지
• /
• 제23권3호
• /
• pp.128-135
• /
• 2018

In this study, the following conclusions could be obtained from the analysis of emissions contribution rates and features for contaminated emissions by 13,456 gasoline vehicles passed in the vehicle load test (ASM-idle) under the inspection year 2013 to 2017. It was confirmed that the contamination of the CO, HC, NOx by the displacement is reduced on over 3L engine. As a result of comparing the exhaust gas in the low speed idle mode and the AS2525 mode, the exhaust gas in the low speed idle mode was measured high. It is estimated that if ISG function is applied, emissions from idle condition will be reduced. NOx emissions were reduced when the engine power was above 200HP. It has been confirmed that the amount of exhaust emissions are significantly reduced for vehicles manufactured after 2004. As a result of analyzing the exhaust gas according to the season, it is judged that there is a correlation between HC and NOx according to the ambient temperature. The concentration of exhaust emission in vehicles with high accumulated distance increases, which is considered to be the result of aging of the vehicle.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.28-34
• /
• 2010

Railway wheel and axle is the most critical components in railway system. A wheel and axle failure can cause a derailment with its attendant loss of life and property. The service conditions of railway vehicles have become severe in recent years due to a general increase in operating speeds. Therefore, more precise evaluate of wheelset strength and safety has been desired. Fracture mechanics characteristics such as dynamic fracture toughness, fatigue threshold and charpy impact energy with respect to the tread, plate, disc hole of wheel and the surface of press fitted axle are evaluated. This paper describes the difference of fracture toughness, fatigue crack growth and fatigue threshold at the locations of wheel and axle. The results show that the dynamic fracture toughness, $K_{ID}$, is obviously lower than static fracture toughness, $K_{IC}$ and the fracture mechanics characteristics are difference to the location of wheel tread and hole.

• 한국군사과학기술학회지
• /
• 제24권1호
• /
• pp.84-98
• /
• 2021

The hydrodynamic characteristics of amphibious assault vehicles are investigated using commercial CFD code, STAR-CCM+. Resistance performances of a displacement-type vehicle and a semi-planing type vehicle are analyzed in calm water. The self-propelled model is also computed for the semi-planing type vehicle. All computations are performed using an overset mesh system and a RANS based flow-solver coupled with a two-degree of freedom equations of motion. A moving reference frame is applied to simulate revolutions of impeller blades for a waterjet propulsion system. Grid dependency tests are performed to evaluate discretization errors for the mesh systems. The numerical analysis results are compared with the experimental results obtained from model tests. It is shown that RANS is capable of investigating the resistance and self-propulsion characteristics of high-speed amphibious assault vehicles. It is also found that a fully covered side skirt, which is covering tracks, reduces resistance and stern trim, besides increasing propulsive efficiency.

• Journal of Electrical Engineering and Technology
• /
• 제7권2호
• /
• pp.200-206
• /
• 2012

In order to develop a deep-underground great train express (GTX) in South Korea, the specifications decision and development of a traction control system (including an inverter and a traction motor), which considers a variety of route conditions, must be advanced. In this study, we examined the running resistance properties of a high-speed traction system based on a variety of tunnel types and vehicle organization methods. Then, we studied the power requirements necessary for the traction motor to maintain balanced speed in the high-speed traction system. From this, we determined the design criteria for the development of a high-speed traction system for use in the deep-underground GTX. Finally, we designed a linear induction motor (LIM) for a propulsion system, and we used the finite element method (FEM) to analyze its performance as it travelled through deep-underground tunnels.