• 한국주조공학회지
• /
• 제42권6호
• /
• pp.392-397
• /
• 2022

In order to compliant the stringent exhaust emission regulations, higher fuel efficiency and cleaner exhaust gas in combustion engines have been required. To improve combustion efficiency, an exhaust gas temperature is increasing, therefore higher temperature resistance is required for components in exhaust system, especially turbine wheel in turbocharger. IN100 looks quite attractive candidate as it has high temperature properties with low density, however it has low castability due to poor ductility at high temperature. In this study, the balance of Al and Ti composition was optimized from the base alloy IN100 to improve the high temperature ductility by expanding the γ single phase region below the solidification temperature, while obtaining the high temperature strength by maintaining the volume fraction of γ' phase equivalent to IN100 around 1000℃. Furthermore, the high temperature creep rupture life increased by adding a small amount of Ta. The alloy developed in this study has high castability, low density and high specific strength at high temperature.

• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.238-245
• /
• 1999

For the optimal design of plasma facing components of a fusion reactor, thorough understanding of thermal behavior of high heat. nux components are required. The purpose of this research is to investigate the characteristics of heat flow and thermal stress in divertors which are exposed to high heat load varing with time and space-Numerical simulations of heat now and thermal stress for three types of diverter are performed using finite volume method and finite element method. Respectly, commercial FLUENT code are used in the heat flow simulation, and maximum surface temperature, temperature distribution and cooling rate are calculated. Commercial ABQUS code are used for calculating temperature distribution. thermal stress, strain and displacement. Through this computer simulation. design data for cooling system and Structural provided.

• Journal of Ginseng Research
• /
• 제9권2호
• /
• pp.170-178
• /
• 1985

Korean red ginseng tails was extracted with solutions having various ethanol concentration at the temperature range of 70-100 $^{\circ}C$. Extraction was carried out for 1-5 times of 8 hours at given temperature. The results obtained on physicochemical properties of yields, saponins, sugars, minerals, color and viscosity were analyzed statistically to find the correlation with extracting conditions. A very high positive correlation was found between extraction time and cumulative values of yields of chemical components. Increase in ethanol concentration affected negatively on viscosity, absorbencies and yields of soluble solids and minerals. Some of the properties also showed a high correlation with temperature increase. Equations were also derived from the significant results on correlation analysis.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.108-111
• /
• 2007

It's important to measure quantitative properties about thermal-nano variation conduct of polymer for producing high quality components using NIL process. NanoScale indents can be used ad cells for molecular electronics and drug deliver, slots for integration into nanodevices, and defects for tailoring the structure and properties. In this study, it's to evaluate mechanical characteristic of polymer such as PMMA and PC at high temperature for manufacture of nano/micro size of polymer using indenter at high temperature. At high temperature mechanical properties of polymer have extreme variation. Because heating the polymer, it becomes softer than room temperature. In this case it is especially important to study for mechanical properties of polymer at high temperature.

• Nuclear Engineering and Technology
• /
• 제53권7호
• /
• pp.2407-2417
• /
• 2021

A structural integrity evaluation program (STEP) was developed for the high temperature reactor design evaluation according to the ASME Boiler and Pressure Vessel Code (ASME B&PV), Section III, Rules for Construction of Nuclear Facility Components, Division 5, High Temperature Reactors, Subsection HB. The program computerized HBB-3200 (the design by analysis procedures for primary stress intensities in high temperature services) and Appendix T (HBB-T) (the evaluation procedures for strain, creep and fatigue in high temperature services). For evaluation, the material properties and isochronous curves presented in Section II, Part D and HBB-T were computerized for the candidate materials for high temperature reactors. The program computerized the evaluation procedures and the constants for the weldment. The program can generate stress/temperature time histories of various loads and superimpose them for creep damage evaluation. The program increases the efficiency of high temperature reactor design and eliminates human errors due to hand calculations. Comparisons that verified the evaluation results that used the STEP and the direct calculations that used the Excel confirmed that the STEP can perform complex evaluations in an efficient and reliable way. In particular, fatigue and creep damage assessment results are provided to validate the operating conditions with multiple types of cycles.

• 한국정밀공학회지
• /
• 제12권7호
• /
• pp.46-52
• /
• 1995

This paper proposes methodologies for the development of radiation thermometer using InSb photo-detector of which spectral sensitivity is excellent over the wave length range of 2 .mu. m .approx. 5 .mu. m. The proposed radiation thermometer has broad measurement range from normal to high, up to more than 1000 .deg. C, with high accuracy, and can measure temperature on the material surface or heat emission noncontactely with high speed. Optical system was consisted of two convex lens with foruslength of 15.2mm for infrared lay focusing, Ge filter to cut the short wave length components and sapphire filter to cut the long wave length components. The cold shielded was installed in the whole surface of the light-absorbing element to remove the error- mometer, calibration using black body furnace which has temperature range of 90 .deg. C .approx. 1100 .deg. C was carried out, and temperature calaibration curve was obtained by exponential function curvefitting. The result shows maximum error less than 0.24%(640K .+-. 1.6K) over the measurement range of 90 .deg. C .approx. 700 .deg. C, and from this result the usefulness of the developed thermometer has been confirmed.

• 한국연초학회지
• /
• 제27권1호
• /
• pp.127-133
• /
• 2005

This study was conducted to determine the aroma and volatile component changes from a different stalk positions of Korean flue-cured tobacco. Eight different stalk positions of flue-cured leaf tobaccos harvested in 2001 were used for this study. Thermal extraction method at two different treatment temperature($50\;amp;\;80^{\circ}C$) was applied for this experiment. Forty eight kinds of aroma and volatile components such as 2,4-heptadienal, hexadecane, 1-methyl-1H- pyridine, 2,5-dimethyl-1H-pyrrole were analyzed by using thermal extraction method. All of aroma and volatile components of leaf tobaccos were changed from a different stalk positions and treatment temperature. Leaf tobaccos in middle stalk position have a higher concentration of aroma and volatile components such as norsolanidione, 4-pyridinecarboxaldehyde, 4-methyl-4-OH-2-pentanone, acetic acid, propylene glycol, 1-methyl-2-pyrrolidinone, 2,5-dimethyl-1H-pyrrole. Also, Megastigmatrienone 1, 3-oxo-[alpha]­ionol, 6,10,14-trimethyl-2-pentadecanone, heptadecane, 6-methyl-2-isohexyl-l-heptene concentration were low in the middle stalk position and high in both bottom and upper position. Treatment temperature affected on the changes of many aroma and volatile components in leaf tobacco. Most of aroma and volatile components such as, 2,4-Heptadienal, dodecanoic methylester, famesol isomer and 3-acetylpyridine were sharply increased as increasing treatment temperature. This results can be used to estimate the aroma characteristics of cigarette blend using a different stalk position of leaf tobacco.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 1997년도 추계학술발표회 논문집
• /
• pp.86-100
• /
• 1997

• 한국공작기계학회논문집
• /
• 제17권6호
• /
• pp.28-34
• /
• 2008

Mg alloy is widely used for the IT, auto and consumer electronics industries. Semi-solid casting(SSC) of magnesium alloys is used to produce high quality components. SSC process is analogous with the injection molding of plastics. The high strength and low weight characteristics of magnesium alloys render the high-precision fabrication of thin-walled components with large surface areas. To produce thin-walled magnesium alloy parts, SSC process parameters on the quality of the finished product should be clearly studied. In this paper, to select optimal process parameters, Taguchi method is applied to the optimal design of the process parameters in the SSC process. The die temperature, injection velocity and barrel temperature of the SSC process are selected for the process parameters. The effectiveness of the optimal design is verified through the CAE software.

• 한국해양공학회지
• /
• 제13권3호통권33호
• /
• pp.92-99
• /
• 1999

High temperature and pressure materials in power plant are degraded by creep damage, if they are exposed to constant loads for long times, which occurs in load bearing structures of pressurized components operationg at elevated temperatures. Many conventional measurement techniques such as replica method, electric resistance method, and hardness test method for measuring creep damgage have been used. So far, the replica method is mainly used for the inspection of high temperature and pressure components. This technique is, however, restricted to applications at the surface of the testpieces and cannot be used to material inside. In this paper, ultrasonic evaluation for the detection of creep damage in the form of cavaties on grain boundaries or intergranular microcracks were carried out. And the absolute measuring method of quantitative ultrasonic velocity technique for Cr-Mo material degradation was analyzed. As a result of ultrasonic tests for crept for specimens, we founded that the sound velocity was decreased as increase of creep life fraction(${phi}c$) and also, confirmed that hardness was decreased as increase of creep life fraction(${phi}c$).