• 산업기술연구
• /
• 제21권B호
• /
• pp.287-294
• /
• 2001

This study is aimed to evaluate the springback characteristics of automotive steel sheets through the S-rail forming test and to find the process condition under which springback can be reduced. Die set for the S-rail test has been made according to the dimension of the NUMISHEET '96 benchmark model. Experiment and finite element analysis have been performed on two kinds of automotive steel sheets: mild steel, SPCEN and high strength steel, SPRC. The test results show that the amount of springback is larger on the high strength steel SPRC than on the mild steel SPCEN, and decreases with increasing blank holding force as the case of material flow. And the reduction of friction has the effect of lowering the blank holding force in view of punch force and material flow. It is shown that the strain distribution over the whole specimen and along the specified sections calculated from the finite element analysis coincides with the measured data except local differences.

• 소성∙가공
• /
• 제29권6호
• /
• pp.338-346
• /
• 2020

A V-bending test was performed in order to predict springback of high-strength steel sheets under various conditions. The results of V-Bending test were analyzed with artificial neural networks and FE-simulation, respectively, for the tool design. The results of design are discussed. The bending test result using the tool designed with artificial neural networks was about 92˚. However, the bending test result using the tool designed FE-simulation was about 94.5˚. Artificial neural networks are a useful tool along with FE-simulation in predicting springback.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.42-62
• /
• 1997

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. Recently, automobile industries are trying to replace partly steel sheets with aluminum alloy sheets. Among currently produced aluminum alloys, Al alloy sheets of Al-Mg-Si(6000 series) are being tested. Especially, 6000 series are the most probable substitute in view of strength and weldability. In this paper, an attempt was made to apply resistance spot welding to joining of dissimilar sheet metals (KS6383+SCPZn or KS6383+SHCP). An effort was made to balance heating rate in the Al alloy with that in the steel sheets by increasing electrode tip diameter. Although resistance spot welding of Al alloy sheet and sheet metals does not produce desirable nugget, it proved to have reasonable strength if optimal weld condition is found by tensile-shear strength and fatigue life test. Since spot weld joints in automobile are always experiencing repeated load, spot welding methodology proposed in this paper is found to be not suitable to automobile body manufacturing.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.305-311
• /
• 2005

The die development of the high-strength steel sheet has big difference on the formability compared with the general panels. Especially, the springback after stamping of the high-strength steel sheets shows big problem. In this study, for the die development of the high-strength steel sheets, write about examples reducing the lead time and the expense of the die development after CAD modification with the result of the springback analysis after finding the best design planning as several times stamping analysis.

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.141-147
• /
• 2008

Hot-dip galvannealed sheet (GA) with high strength of 590MPa grade in tensile strength, has developed for automotive applications. However, for a successful application, the microstructure and galvannealing behavior of galvannealed TRIP steel sheets must be strictly controlled. High silicon contents steel has problems with weld-ability, zinc coating and reduction of retained austenite volume fraction after galvannealing process. The main purpose of this study is to solve the problem as indicated above.

• 한국산학기술학회논문지
• /
• 제11권9호
• /
• pp.3155-3160
• /
• 2010

최근 자동차 산업은 고효율 자동차의 개발에 박차를 가하고 있으며 이에 따라 차체 경량화 및 내식성 방지를 위한 고강도강 및 도금강의 사용이 증가하고 있다. 이에 따라 본 연구에서는 자동차 차체에 쓰이는 3종의 다른 강판에 대하여, 겹침 순서에 따른 용접 특성을 시뮬레이션 기법을 이용하여 분석하였다. 자동차 차체에 많이 사용되는 EDDQ 급의 도금강판 0.7t와 인장강도 440 MPa급의 440R 1.2t, 그리고 AHSS (Advanced High Strength Steel)인 DP 590 0.2t 판재에 대하여 겹치기 순서에 따른 용접 특성을 시뮬레이션 하였고, 너겟 성장 곡선 및 전류에 따른 너겟의 크기로 그 용접성을 분석하였다. 또한 용접 시 발생되는 각 접촉부의 접촉저항을 이용하여 겹침순서에 따른 너겟의 크기를 분석하였으며, 이를 통해 최적의 겹치기 순서를 제안할 수 있었다.

• 소성∙가공
• /
• 제27권3호
• /
• pp.145-153
• /
• 2018

Magnesium material could be widely used in the automotive industry because of its high strength to weight ratio, but the electric resistance spot welding process of magnesium sheets is difficult because of its low electric resistance and high thermal conduction and thermal expansion. For this reason, an electric resistance surface friction spot welding process using rotating dies is suggested for the spot welding of magnesium metal sheets. This welding method can be characterized by three heating methods: (1) electric resistance heating on contacted surface, (2) surface friction heating by rotating dies, and (3) thermal conduction heating from heated steel electrodes, for the fusion of metal at the interfacial zone between the two magnesium sheets. This welding process also has variables to explore, such as welding currents, diameters of the steel electrode, and rotating dies. It was found that the welding strength could reach industrial requirements by applying a welding current of 11.0kA, with steel electrodes of 12mm diameter, with rotating dies of 4.4 mm diameter, under the condition of a revolution speed of 1200rpm of rotating dies, for the surface friction spot welding process of AZ31 magnesium alloy sheets of 1.4mm thickness.

• Corrosion Science and Technology
• /
• 제10권2호
• /
• pp.47-51
• /
• 2011

Main issues in the automotive industry are the reduction of vehicle body weight for energy savings and improvement of crashworthiness for passenger safety. In order to address both these issues, there has recently been increasing application of galvannealed advance high strength steel (GA AHSS) sheets for automobiles. However, GA AHSS sheets have some surface defects such as coating bare spots due to the addition of solid-solution strengthening elements, which result in the deterioration of the galvannealing reaction. In this study, the effects of galvannealed manufacturing conditions on surface and mechanical properties, resistance spot weldability on a laboratory scale, and GA 980 MPa steel sheets produced by commercial continuous galvannealing line (CGL) were investigated.

• 대한기계학회논문집A
• /
• 제26권1호
• /
• pp.147-152
• /
• 2002

Effect of lip shape on the hole flangeability of high strength steel sheets is investigated. Circular plates of various hole sizes are tested and the variation of lip length as well as the variation of thickness on the sectional views of the finished lip were studied. The conventional hole flanging process is limited to a certain limit hole diameter below which failure will ensue during the hole expansion. The intention of this work is to examine the effect of lip shape on the flangeability of TRIP steel and Ferrite-Bainite duplex steel and find out major parameters which can affect flanging shape of high strength hot rolled steels. Over the ranges of conditions investigated, the minimum hole diameter of F+B steel is better than TRIP steel. while, the lip-shape accuracy of TRIP steel is better than that of F+B steel. although the tensile strength and elongation of %P steel are superior than those of Ferrite-Bainite duplex steel, the flangeability is found to be not so strongly sensitive to the tensile properties but sensitive to displacement on the circumferential direction of hole edge.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 제4회 박판성형 심포지엄
• /
• pp.35-40
• /
• 2003

In order to develope springback control technology for high-strength steel sheets, some studies have been conducted: dome stretching test, stepped s-rail forming and springback measurement, and optimally shaped initial blank design. First, to find out the formability of TRIP60, dome stretching test was performed. Next the stepped s-rail die, which was designed to form a channel type panel with large twist and wall curl, was manufactured and used to know the effect of controlling forming variables, such as blank holding force and flange amount on the springback. Furthermore, new measurement method of the springback was introduced to define wall curl and twist in geometrically complex panels. Finally, the optimally shaped initial blank was employed to verify one of the best ways to control the springback in channel type, high strength sheet panels.