• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.8-14
• /
• 2013

Hydrogen-natural gas blends(HCNG) engine is optimizing technology of performance and emission characteristics with use of hydrogen's fast flame speed and wide flammability limit. As lean-burn limit is extended, the improvement in thermal efficiency and harmful emissions can be achieved. However, the extension of lean-burn limit under a wide open throttle operation point could be realized with the increase in boosting capacity in a lean-burn engine with turbo-charging system. In the present study, the power output characteristics of HCNG engine with turbo-charger change is assessed and feasibility of the increase in boosting capacity is evaluated. The turbo-charger design with high efficiency at higher flow rate rather than higher boosting pressure makes efficient operation possible at relatively rich mixture condition.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Journal of the Korean Magnetics Society
• /
• v.26 no.1
• /
• pp.24-30
• /
• 2016

MFL (Magnetic flux leakage) type nondestructive testing has been used for inspection of underground gas pipelines to find metal defects by detecting magnetic leakage signal. Because the underground gas pipeline is exposed by environment such as high pressure with great humidity, external defects are easily formed on the surface of pipelines and they are being grouped respectively. These adjacent defects cause the signal distortion of leakage flux so that it is hard to estimate the shape information of defects. In this paper, we performed to study of the signal distortion and compensating method for multiple defects in MFL type nondestructive testing system by using 3D FEM simulation. This paper proposes the basic algorithm of defect signal analysis on multiple defects on the surface of 30 inch diameter pipeline.

• Corrosion Science and Technology
• /
• v.20 no.1
• /
• pp.26-36
• /
• 2021

Pipes operating in the seawater environment faces cavitation degradation and corrosion of the metallic component, as well as a negative synergistic effect. Cavitation degradation shows the mechanism by which materials deteriorate by causing rapid change of pressure or high-frequency vibration in the solution, and introducing the formation and explosion of bubbles. In order to rate the cavitation resistance of materials, constant conditions have been used. However, while a dynamic cavitation condition can be generated in a real system, there has been little reported on the effect of ultrasonic amplitude on the cavitation resistance and mechanism of composites. In this work, 3 kinds of epoxy coatings were used, and the cavitation resistance of the epoxy coatings was evaluated in 3.5% NaCl at 15 ℃ using an indirect ultrasonic cavitation method. Eleven kinds of mechanical properties were obtained, namely compressive strength, flexural strength and modulus, tensile strength and elongation, Shore D hardness, water absorptivity, impact test, wear test for coating only and pull-off strength for epoxy coating/carbon steel or epoxy coating/rubber/carbon steel. The cavitation erosion mechanism of epoxy coatings was discussed on the basis of the mechanical properties and the effect of ultrasonic amplitude on the degradation of coatings.

• Journal of Lipid and Atherosclerosis
• /
• v.7 no.2
• /
• pp.98-109
• /
• 2018

Objective: To examine the effects of sodium intake on the correlations between the saltsensitive gene ${\alpha}$-adducin 1 (ADD1) and inflammatory cytokines in Korean childhood obesity. Methods: A total of 2,070 students aged 8-9 years old participated in this study. The anthropometrics, serum biochemistry profile, inflammatory cytokines, and three-day dietary assessment were analyzed according to sex, obesity degree, and ADD1 polymorphism. Results: The obesity prevalence was higher in boys (15.6%) than in girls (11.9%). Boys also showed higher values in anthropometrics; lipid, glucose, and insulin profiles; total calorie intakes, as well as those of sodium and calcium compared with those of the girls. The more obese were boys and girls, the higher were the anthropometrics and the blood levels (total cholesterol, triglyceride, low-density lipoprotein cholesterol, fasting blood sugar, and insulin), but the lower was high-density lipoprotein cholesterol. The obese boys had significantly higher sodium and Na/K intakes, while the obese girls had higher visfatin level and Na/K intake. In addition, an increase in the risk factors for blood pressure and obesity in ADD1 variants was identified. Serum tumor necrosis $factor-{\alpha}$($TNF-{\alpha}$) significantly increased with increasing sodium intake in the ADD1 W allele carriers, regardless of sex. The presence of obesity with the ADD1 W allele induced inflammatory accelerators such as $TNF-{\alpha}$ or C-reactive protein(CRP) with higher sodium intake. Conclusion: Obese children with an ADD1w allele can experience a more complex form of obesity than non-obese when exposed to an obesity-inducing environment and need to be controlled sodium intake in the diet.

• Horticulture, Environment, and Biotechnology : HEB
• /
• v.59 no.6
• /
• pp.827-833
• /
• 2018

Plasma lighting systems have been engineered to simulate sunlight. The objective of this study was to determine the effects of plasma lighting on tomato plant growth, photosynthetic characteristics, flowering rate, and physiological disorders. Tomato plants were grown in growth chambers at air temperatures of $25/23^{\circ}C$ (light/dark period), in a $16h\;day^{-1}$ light period provided by four different light sources: 1 kW and 700 W sulfur plasma lights (1 SPL and 0.7 SPL), 1 kW indium bromide plasma light, and 700 W high pressure sodium lamp (0.7 HPS) as a control. The totaldry weight and leaf area at 0.7 SPL were approximately 1.2 and 1.3 times greater, respectively, than that of 0.7 HPS at the 62 days after sowing (DAS). The maximum light assimilation rate was observed at 1 SPL at the 73 DAS. In addition, the light compensation and saturation points of the plants treated with plasma lighting were 98.5% higher compared with HPS. Those differences appeared to be related to more efficient light interception, provided by the SPL spectrum. The percentage of flowering at 0.7 SPL was 30.5%, which was higher than that at 0.7 HPS; however, there were some instances of severe blossom end rot. Results indicate that plasma lighting promotes tomato growth, flowering, and photosynthesis. Therefore, a plasma lighting system may be a valuable supplemental light source in a greenhouse or plant factory.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.1
• /
• pp.20-29
• /
• 2021

This study developed a smartwatch and a wind speed system in accordance with the necessity of a device that provides the information required in marine leisure. Based on a marine leisure smartwatch with a multi-sensor, a gyro box, and a wind speed system, external data such as GPS, motion, humidity, temperature, air pressure, and heart rate can be collected. In addition, the collected external environment data can be managed through an application on a smartphone, which is an Android-based mobile device. The developed smartwatch and wind speed system are expected to contribute to increasing accessibility and revitalization of the marine leisure industry. In addition, in terms of safety and education, the need for a device that provides marine information is large, so it is expected to increase the possibility of entering the high value-added market and improve the product localization rate.

• Structural Engineering and Mechanics
• /
• v.77 no.2
• /
• pp.167-177
• /
• 2021

Due to various benefits such as unlimited degrees of freedom, environment adaptability, and safety for humans, engineers have used soft materials with hyperelastic behavior in various industrial, medical, rescue, and other sectors. One of the applications of these materials in the fabrication of bending soft actuators (SA) is that they have eliminated many problems in the actuators such as production cost, mechanical complexity, and design algorithm. However, SA has complexities, such as predicting and monitoring behavior despite the many benefits. The first part of this paper deals with the prediction of SA behavior through mathematical models such as Ogden and Darijani, and its comparison with the results of experiments. At first, by examining different geometric models, the cubic structure was selected as the optimal structure in the investigated models. This geometrical structure at the same pressure showed the most significant bending in the simulation. The simulation results were then compared with experimental, and the final gripper model was designed and manufactured using a 3D printer with silicone rubber as for the polymer part. This geometrical structure is capable of bending up to a 90-degree angle at 70 kPa in less than 2 seconds. The second section is dedicated to monitoring the bending behavior created by the strain sensors with different sensitivity and stretchability. In the fabrication of the sensors, silicon is used as a soft material with hyperelastic behavior and carbon fiber as a conductive material in the soft material substrate. The SA designed in this paper is capable of deforming up to 1000 cycles without changing its characteristics and capable of moving objects weigh up to 1200 g. This SA has the capability of being used in soft robots and artificial hand making for high-speed objects harvesting.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.1
• /
• pp.9-17
• /
• 2022

As the COVID-19 pandemic situation worsens, the time spent indoors increases, and the exposure to indoor environmental pollution such as indoor air pollution and noise also increases, causing problems such as deterioration of human health, stress, and discord between neighbors. This paper designs and implements a system that measures and monitors indoor air quality and noise, which are representative evaluation criteria of the indoor environment. The system proposed in this paper consists of a particulate matter measurement subsystem that measures and corrects the concentration of particulate matters to monitor indoor air quality, and a noise measurement subsystem that detects changes in sound and converts it to a sound pressure level. The concentration of indoor particulate matters is measured using a laser-based light scattering method, and an error caused by temperature and humidity is compensated in this paper. For indoor noise measurement, the voltage measured through a microphone is basically measured, Fourier transform is performed to classify it by frequency, and then A-weighting is performed to correct loudness equality. Then, the RMS value is obtained, high-frequency noise is removed by performing time-weighting, and then SPL is obtained. Finally, the equivalent noise level for 1 minute and 5 minutes are calculated to show the indoor noise level. In order to classify noise into direct impact sound and air transmission noise, a piezo vibration sensors is mounted to determine the presence or absence of direct impact transmitted through the wall. For performance evaluation, the error of particulate matter measurement is analyzed through TSI's AM510 instrument. and compare the noise error with CEM's noise measurement system.

• International Journal of Computer Science & Network Security
• /
• v.22 no.10
• /
• pp.57-66
• /
• 2022

The aim of the article is to investigate socio-political processes in Ukraine on the basis of institutional and behavioral approaches, in particular their regulatory and informational support. Methodology. To determine the nature and content of sociopolitical processes, the following approaches have been used: 1. Institutional approach in order to analyze the development of Ukraine's political institutions. 2. The behavioral approach has been used for the analysis of socio-political processes in Ukraine in the context of political behavior of citizens, their political activity which forms the political culture of the country. Results. The general features of the socio-political situation in Ukraine are as follows: the formed model of government, which can be conditionally described as "presidential"; public demand for new leaders remains at a high level; the society has no common vision of further development; significant tendency of reduction of real incomes of a significant part of the society and strengthening of fiscal pressure on businessmen will get a public response after some time. Increasing levels of voice, accountability, efficiency of governance and the quality of the regulatory environment indicate a slow change in the political system, which will have a positive impact on public sentiment in the future. At the same time, there has been little change in the quality of Ukraine's institutions to ensure political stability, the rule of law and control of corruption. There are no cardinal changes in the development of the institution of property rights, protection of intellectual rights, changes in the sphere of ethics and control of corruption. Thus, Ukraine's political institutions have not been able to bring about any change in the social-political processes. Accordingly, an average level of trust and confidence of citizens in political institutions and negative public sentiment regarding their perception and future change can be traced in Ukraine.