• Nuclear Engineering and Technology
• /
• v.45 no.1
• /
• pp.53-60
• /
• 2013

Bentonite is generally used as a buffer material in high-level radioactive waste disposal facilities and consists of 50% quartz by weight. Quartz strongly affects the behavior of bentonite over very long periods. For this reason, quartz dissolution experiment was performed under high-pressure and high-alkalinity conditions based on the conditions found in a high-level radioactive waste disposal facility located deep underground. In this study, two quartz dissolution experiments were conducted on 1) quartz beads under low-pressure and high-alkalinity conditions and 2) a single quartz crystal under high-pressure and high-alkalinity conditions. Following the experiments, a confocal laser scanning microscope (CLSM) was used to observe the surfaces of experimental samples. Numerical analyses using the finite element method (FEM) were also performed to quantify the deformation of contact area. Quartz dissolution was observed in both experiments. This deformation was due to a concentrated compressive stress field, as indicated by the quartz deformation of the contact area through the FEM analysis. According to the numerical results, a high compressive stress field acted upon the neighboring contact area, which showed a rapid dissolution rate compared to other areas of the sample.

• Journal of Soil and Groundwater Environment
• /
• v.29 no.1
• /
• pp.1-9
• /
• 2024

As part of monitoring technology aimed at verifying the stability of CO₂ geologic storage and mitigating concerns about leakage, a method for measuring the pH and alkalinity of high-pressure fluid samples was established to obtain practical technology. pH measurement for high-pressure samples utilized a high-pressure pH electrode, and alkalinity was measured using the Gran titration method for samples collected with a piston cylinder sampler (PCS). Experimental samples, referencing CO₂-rich water and CO₂ geologic storage studies, were prepared in the laboratory. The PCS controls the piston, preventing CO₂ degassing and maintaining fluid pressure, allowing mixing with KOH to fix dissolved CO₂. Results showed a 6.1% average error in high-pressure pH measurement. PCS use for sample collection maintained pressure, preventing CO₂ degassing. However, PCS-collected sample alkalinity measurements had larger errors than non-PCS measurements, limiting PCS practicality in monitoring field settings. Nevertheless, PCS could find utility in preprocessing for carbon isotope analysis and other applications. This research not only contributes to the field of CCS monitoring but also suggests potential applications in studies related to natural analogs of CCS, CO₂-rock interaction experiments, core flooding experiments, and beyond.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.865-871
• /
• 2018

The 3-way valve have been used as a valve for opening and closing the valve by the flow control in the pressure system of the cryogenic and high pressure environment. In this paper, numerical analysis and experimental study on fracture nipple of 3-way ultra high pressure valve applied to space launch vehicle was carried out. We have developed a 3-way valve numerical simulation modeler of cryogenic environment using commercial software ANSYS 18.2. As results of numerical analysis, optimum nipple condition was derived. In addition, a 3-way valve prototype was fabricated and the fracture test was performed and compared with the numerical analysis results.

• Fire Science and Engineering
• /
• v.27 no.1
• /
• pp.52-59
• /
• 2013

In this study, tests were conducted to establish a fire engine of relay waterproof and utilization in order to maintain the pressure in a situation that require high-pressure water-resistant such as a high-rise building fire, etc. As a result of test on the change of a relay waterproof pressure, the measurement result with the hydrant intake of a fire engine opened has reduced approximately 20 % compared to the measurement result with the hydrant intake closed. Similar efficiency showed in the test result that change the pressure of 2 fire engines respectively to use them more efficiently at a fire fighting activity site. A fire engine operation and utilization is proposed based on this study result in order to cope effectively with a fire site requiring high-pressure stream in a high-rise building fire, etc. by using a fire engine held at present because there is no fire pump with high-pressure stream ability arranged at the fire station and there is no regulation on high-pressure fire-fighting pumps in a type approval and verification technology criterion for a fire engine.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.267-272
• /
• 2010

High pressure x-ray diffraction patterns of ${\alpha}$-cristobalite gallium phosphate ($GaPO_4$) were acquired up to 8.9 GPa at room temperature using Mao-Bell type diamond anvil cell with high flux synchrotron radiation. Starting orthorhombic phase (phase-I) shows the splitting of peak which is possibly resulted from the pressure induced orientation disorder of the framework structure of tetrahedra. This is designated as phase-I'. This phase transforms to the orthorhombic high pressure phase-III between 2 and 3 GPa. Present phase transition sequence is not in accord with the recent high pressure X-ray diffraction results performed on the same starting sample (Ming et al., 2007). X-ray pattern of the unloaded sample to ambient pressure shows that the structure retains that of the high pressure phase prior to decompression.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.148-153
• /
• 2004

It is well-known that the mechanical behavior of fiber-reinforced composites under hydrostatic pressure environment is different from that of atmospheric pressure environment. It is also known that the mechanical behavior of fiber-reinforced composites is affected by a strain rate. In this work, we investigated the effect of strain rate on the compressive elastic modulus, fracture stress, and fracture strain of carbon/epoxy composites under hydrostatic pressure environment. The material used in the compressive test was unidirectional carbon/epoxy composites and the hydrostatic pressures applied was 270㎫. Compressive tests were performed applying three strain rates of 0.05％/sec, 0.25％/sec, and 0.55％/sec. The results showed that the elastic modulus increased with increasing strain rate while the fracture stress was little affected by the strain rate. The results also showed that the fracture strain decreased with increasing strain rate.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.4
• /
• pp.361-367
• /
• 1995

This study has been carried out to investigate the filteration performance of Electrostatically Stimulated Fabric Filter(ESFF) at high temperature condition. The electric field was maintained parallel to the fabric surface. The benefits of ESFF are lower residual pressure drop, improvement of fine particle removal efficiency and increasing reduced rate of pressure drop during a filteration cycle, stable operation at higher filtering velocities. According to the variance of filtering velocities and dust loadings, the results are summarized as follows; By imposing an electric field on the filter, the reduced rate of pressure drop was 7.sim.18% at room temperature, and when filtering velocity was 1.8m/min and dust loading was 1g/m$^{3}$, the value of reduced rate of pressure drop was shown the highest. Under the electric field around the filter, the reduced rate of pressure drop was 10.sim.35% at high temperature, and when filtering velocity was 1.8m/min and dust loading was 1g/m$^{3}$, the value of reduced rate of pressure drop was shown the highest. Most of all, at high temperature, the value of reduced rate of pressure drop was resulted to 25%. Also the collecting efficiency was shown clearly improved. By the SEM photo analysis, the number of penetrated particles at the Conventional Fabric Filter was approximately two times that of Electrostatically Stimulated Fabric Filter.

• Journal of People, Plants, and Environment
• /
• v.22 no.5
• /
• pp.445-454
• /
• 2019

This study was conducted to find out physical changes in the blood pressure and saliva cortisol of patients with high blood pressure and diabetes after participating in agro-healing activities. The saliva cortisol and blood pressure of 14 males and females aged 49.79±10.48 on average were measured after participating in agro-healing activities. The saliva collection system was used, and their satisfaction level for the program was also surveyed. Changes in the values before and after participating in the agro-healing activities were compared and analyzed. The cortisol concentration, a stress hormone, was reduced from 6.76nmol/L before the program to 4.86nmol/L after the program, down by 1.9nmol/L, which was a statistically significant difference (z=-3.170, p<.01). In addition, the cortisol concentration was gradually reduced through the entire program from Session 1 to Session 7. Changes in the blood pressure of subjects before and after participating in agro-healing activities were examined, and the total systolic and diastolic blood pressure continuously decreased after participating in agro-healing activities through the entire program from Session 1 to Session 7. Their systolic blood pressure was reduced statistically significantly (z=-1.947, p<.05). Also, participants' satisfaction was analyzed and it was found that more than 95% of participants answered 'satisfied' and 'very satisfied' with agro-healing activities. Therefore, these results indicate that agro-healing activities performed in the healing-farm had a positive impact on the cortisol concentration and blood pressure of patients with chronic diseases such as diabetes and high blood pressure. In addition, their high satisfaction for this program seemed to improve the psychological and physiological conditions of subjects.

• Journal of Korean Society for Atmospheric Environment
• /
• v.10 no.4
• /
• pp.245-251
• /
• 1994

We considered that characteristics of SO$_2$, concentration level and relations of the meteorological parameters and high pollution concentration from the data measured 7 air quality continuous monitoring stations during 4 years, from 1990 to 1993 in Pusan. The SO$_2$ concentration level showed decreasing trend yearly, it was maximum in Winter, minimum in Summer. The time of SO$_2$ peak concentration lagged from seashore to land because of break-down of the nocturnal inversion layer and seabreeze. Ihe correlations of daily SO$_2$, value between various air quality continuous monitoring stations were highest between Beomcheondong and Meongryundong, lowest between Daeyeondong and Sinpyeongdong because of difference of air Pollution emission sources characteristic. The meteorological parameters affecting SO$_2$ concentration level were minimum temperature, relative humidity, wind speed and air pressure. The SO$_2$ high pollution($\geq$95ppb) occurred almost in Winter, particulaly in such day showing lower wind speed and higher air pressure. Elementary SO$_2$ high Pollution Predictor were high pressure system and stability of lower atmosphere.

• Journal of the Korean Society of Combustion
• /
• v.12 no.3
• /
• pp.33-39
• /
• 2007

The present study is mainly motivated to investigate the vaporization, auto-ignition and combustion processes in high-pressure engine conditions. In order to realistically simulate the dimethyl ether (DME) spray dynamics and vaporization characteristics in high-pressure and high-temperature environment, the high-pressure vaporization model is utilized. The interaction between chemistry and turbulence is treated by employing the Representative Interaction Flamelet (RIF) model. The detailed chemistry of 336 elementary steps and 78 chemical species is used for the DME/air reaction. Numerical results indicate that the RIF approach, together with the high-pressure vaporization model, successfully predicts the essential feature of ignition and spray combustion processes.