• Journal of Advanced Marine Engineering and Technology
• /
• 제41권3호
• /
• pp.202-208
• /
• 2017

최근 개발된 선박용 주기관은 추진효율 향상과 연료소비율 저감기술이 요구됨에 따라 과거에 비해 높은 비틀림진동 기진력 특성을 갖고 있다. 따라서 이를 제어하기 위해 기본적으로 엔진 선단에 점성 댐퍼나 점성-스프링댐퍼를 장착한다. 점성댐퍼의 경우 댐퍼 내부에 채워진 실리콘 오일이 탄성적인 연결이 없다고 가정하고 댐퍼설계를 하여 왔으나 고점도 실리콘 오일은 높은 점도에 따른 비틀림 강성이 존재할 뿐만 아니라 작동온도와 주파수에 따라 비선형적인 동특성을 갖는다. 본 논문에서는 고점도 실리콘 오일이 적용된 점성댐퍼의 동특성을 확인하고 해당 댐퍼가 장착된 축계의 비틀림진동 특성을 검토하였다. 이를 위해 점성댐퍼의 최적 동특성을 이론적으로 해석하는 방법을 검토하였고, 고점도 실리콘 오일로 채워진 점성댐퍼로 해당축계의 비틀림진동 제어를 하는 경우 댐퍼 작동온도 및 경년변화를 고려한 추진축계 최적 설계 방안에 대해서 검토하였다.

• Korean Chemical Engineering Research
• /
• 제48권4호
• /
• pp.462-469
• /
• 2010

기체와 액체가 만나는 2상 공정들은 화학공학, 생명화학공학, 환경공학, 식품공학 등에 두루 존재한다. 위와 같은 공정의 최적화를 위해서는 거품의 움직임과 형태에 대한 정확한 파악이 필요하다. 액체 내부에서 거품의 움직임은 액체의 밀도, 점도, 표면장력과 거품의 크기와 속도에 영향을 받는다. 본 논문에서는 고점도 실리콘 오일 내부에서의 거품의 움직임과 형태를 관찰하였다. 또한 국외 논문 및 저서에서 정립된 거품의 에너지 수지 식, 항력계수와 변형계수를 이용하여 거품의 종말속도, 항력계수, 변형계수, 형태를 예측해 보고 이를 실험결과와 비교해 보았다. 실험 결과 거품의 속도는 점도가 낮을 경우가 더 빨랐고, 거품의 항력계수는 점도가 클 때 더 컸다. 거품의 형태는 점도가 클 때 덜찌그러진(구형에 가까운) 형태였다. 실험결과와 국외 논문 및 저서에서 정립된 항력계수와 변형계수를 이용한 예측결과를 비교해 본 결과 Batchelor가 제시한 이론이 가장 정확한 예측을 하는 것으로 나타났다. Batchelor가 제시한 거품의 에너지 수지식, 항력계수와 변형계수를 사용하여 예측한 거품의 2차원 측면 형태는 실험에서 관찰된 거품의 2차원 측면 형태와 유사하였다.

• Tribology and Lubricants
• /
• 제26권2호
• /
• pp.136-141
• /
• 2010

In an oil hydraulic vane pump for an automobile, it is very important that the vane doesn't separate from the camring inner race during the operation of the vane pump. The vane generally has not only the oil hydraulic force acting on the bottom face to contact to camring inner race but there is also an inertial force and viscous force. Because the oil hydraulic force is much larger than the other forces, the contact state between the vane tip and the camring inner race is sufficient. However, the contact state between the vane tip and the camring inner race is only affected by the inertial and viscous forces during the delivery of the vane pump, because the oil hydraulic force acting on the vane is in equilibrium. If the inertial force is larger than the viscous force, which happens when the vane is separated from the camring inner race, the delivery of the vane pump can become unstable or the volume efficiency can become decrease rapidly. Therefore, in this paper, the state of the contact between the vane and the camring is considered. The results show that the rotating speed of the shaft, the operating temperature of the oil, the clearance between the vane and the rotor, and the mass of the vane exert a great influence on the state of the contact between the vane and the camring.

• 동력기계공학회지
• /
• 제1권1호
• /
• pp.98-105
• /
• 1997

In general, crankshafts which are used in internal combustion reciprocating engines are subjects to high torsional vibration. Therefore, a damper is often used to minimize the torsional vibration in reciprocating engines. In this paper, in order to investigate damping performance of viscous damper, the real effective viscosity and complex damping coefficient of silicone oil, and the effective inertia moment of inertia ring are calculated considering the relative motion between damper casing and inertia ring. Based on these results multi-cylinder shaft is modeled into equivalent 2-degree of freedom system and optimum condition is estimated by calculating the amplification factor of viscous damper. Also the test damper was manufactured according to the result of theoretical investigation, the performance and durability was ascertained through experimental examination.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.59-63
• /
• 2001

A high-impulse, low-power, continuous-shot microthruster has been developed using low boiling temperature liquid-propellant with high viscous fluid-plug. The viscous friction force of the fluid-plug increases the blast pressure and the low boiling temperature liquid-propellant is intended to reduce input power consumption. The three-layer microthruster has been fabricated by surface micromachining as well as bulk micromachining in the size of $7{\times}13{\times}1.5mm^{3}$. A continuous output impulse bit of $6.4{\times}10^{-8}N{\cdot}sec$ has been obtained from the fabricated microthruster using perfluoro normal hexane (FC72) propellant and oil plug, resulting in about ten times increase of the impulse bit using one hundredth electrical input energy compared to the conventional continuous microthruster.

• 동력기계공학회지
• /
• 제13권5호
• /
• pp.11-17
• /
• 2009

A numerical study of unsteady mixed convection in a cavity with high viscous fluid is presented. Finite volume method was employed for the discretization and PISO algorithm was used for calculating pressure term. The parameters governing the problem are the Rayleigh number ($10^3\;{\leq}\;Ra\;{\leq}\;10^5$), the Reynolds number (0 < Re $\leq$ 1), and the aspect ratio (0.5 $\leq$ AR $\leq$ 2). The fluid used is silicon oil, a high prandtl number fluid, Pr = 909.1. The results show velocity vectors and temperature distributions. It is found that the periodic flows in a cavity are observed at very low Reynolds numbers, and the period of periodic flow decreases with increasing Reynolds and Rayleigh numbers, and increases with increasing aspect ratio. Also, the Reynolds number range of periodic flow increases with increasing Rayleigh numbers and aspect ratio.

• 설비공학논문집
• /
• 제29권3호
• /
• pp.127-133
• /
• 2017

Performance analysis has been carried out on a high side scroll compressor that had a fixed scroll equipped with a circular oil groove on its thrust surface. Oil was supplied to the oil groove through an intermittent opening from a high pressure oil reservoir formed inside the orbiting scroll hub. Oil in the groove was then delivered to both suction and back pressure chambers by pressure differentials and viscous pumping action of the orbiting scroll base plate. Mathematical modeling of this oil groove system was incorporated into a main compressor performance simulation program for an optimum oil groove design. The study findings were as follows. Pressure in the oil groove can be controlled by changing its configuration and the oil passage area. With an enlarged oil passage, the pressure in the oil groove heightens due to an increased flow rate, but the pressure elevation in the back pressure chamber is small, resulting in reduced friction loss at the thrust surface between the two scrolls. On the other hand, by increasing the oil passage area, the oil content in the refrigerant flow increases. Considering all these factors, the energy efficiency ratio could be improved by about 3.6% under the ARI condition by an optimal oil groove design.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.7-14
• /
• 2000

Nowadays, the viscous damper using high viscosity oil was much to be used for engine shafting system to reduce the excessive additional stress by torsional vibration. In general, it was assumed that the viscous damper could be modelled having only damping coefficient, that is to say, whose stiffness be ignored. But it is found that there exists a jump phenomenon, as a kind of non-linear vibration, in the actual engine shafting system with a damper of high viscosity. Therefore the damper ring and the casing are modelled as two mass elastic system with a complex viscosity. Also, to analyze a non-linear phenomenon, it is assumed that the viscous damper has a linear stiffness coefficient in proportion to the angular amplitude and a non-linear stiffness coefficient in proportion to cube of the angular amplitude. For the analysis, Quasi-Newton method with BFGS(Broyden-Fletcher-Goldfarb-Shanno) formula is used. Both calculated and measured values are provided in this paper which confirm the possibility of applying non-linear theory to engine shafting system with viscous damper.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제10권6호
• /
• pp.471-481
• /
• 2005

Heavy crudes (bitumen) are extremely viscous and contain high concentrations of asphaltene, resins, nitrogen and sulfur containing heteroaromatics and several metals, particularly nickel and vanadium. These properties of heavy crude oil present serious operational problems in heavy oil production and downstream processing. There are vast deposits of heavy crude oils in many parts of the world. In fact, these reserves are estimated at more than seven times the known remaining reserves of conventional crude oils. It has been proven that reserves of conventional crude oil are being depleted, thus there is a growing interest in the utilization of these vast resources of unconventional oils to produce refined fuels and petrochemicals by upgrading. Presently, the methods used for reducing viscosity and upgradation is cost intensive, less selective and environmentally reactive. Biological processing of heavy crudes may provide an ecofriendly alternative or complementary process with less severe process conditions and higher selectivity to specific reactions to upgrade heavy crude oil. This review describes the prospects and strengths of biological processes for upgrading of heavy crude oil.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.44-51
• /
• 2003

By blending of various low boiling point oxygenated agents to lower grade fuels, significant improvements were simultaneously obtained in smoke, CO, PM, SOF and BSEC. Especially, our trends were remarkably obtained by retarding injection timing, by decreasing boiling point and increasing blending contents of additives in case of oxygenated agents rather than non-oxygenated agents. Also, it was revealed that when 20vo1.% DMM added to high viscosity fuels and injection timing was retarded, NOx-smoke trade off relationship was much better than that of ordinary diesel fuel. Thus, lower grade fuels with high viscosity could be expected to be used efficiently and cleanly in diesel operation by blending low boiling point oxygenates.