• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.8-8
• /
• 2009

알루미늄 합금 Al 6082-T6는 최근에 개발되어 북유럽 등의 선진국에서는 그 뛰어난 해양 내식성과 우수한 강도로 인하여 해양구조물의 헬리데크(Helideck), 타워 갱웨이(Tower gangway), 알루미늄 피팅류(Aluminium fitting)등의 해양구조물과 플랫폼(Flatform), 알루미늄 래더(Aluminium ladder)등의 선박부품, 차량, 기계부품 분야에서 전 세계적으로 널리 사용되기 시작하였다. 그러나 전통적으로 용접금속의 기공은 결함으로 분류 되고, Rakesh Kumar 등의 논문에 따르면 용접 시 용접금속 내에 발생되어진 미세기공이 기계적 성질에 악영향을 미치는 것으로 보고되어졌다. 따라서 용접금속내의 발생하는 기공을 방지하는 용접공정의 개발이 반드시 필요하다. 본 연구의 목적은 Al 6082-T6 고속 MIG용접에서 기공방지를 위한 용접공정을 개발하는 것이다. Al 6082-T6의 7t 플레이트에 Al 5356의 와이어를 사용하여 아크길이 변경 및 용접속도를 60cpm과 120cpm으로 변경하여 실험하였고, 용접속도 120cpm의 고속 MIG용접에서 토치 진행각을 변경하여 실험을 진행하였다. 용접공정 파라메터 변경에 따른 기공율 측정은 이미지 분석 소프트웨어를 사용하여 정량적으로 분석하였다.

• Journal of Welding and Joining
• /
• v.33 no.6
• /
• pp.36-41
• /
• 2015

In the automotive industry, TWB hot stamping process is broadly adapted to reduce weight of the car and improve fuel efficiency. However, the process faces a problem of weakened strength of the welded zone after hot stamping process, due to the fact that Al-Si elements of the coating layer penetrating the welded zone. In this study, filler wires with high percentages of carbon and manganese is adapted during laser welding process to secure the strength of the fusion zone. In addition, wire feeding speed and laser welding speed are optimized by sample test.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1299-1306
• /
• 2007

The combination of laser beam and electric arc sharing common weld pool has widely been investigated since the late seventies, but it is beginning of the industrial uses. Recently, laser-GMA hybrid welding process showed possibility to overcome the tight gap tolerance with improved productivity. The laser-arc hybrid welding process is inherently complex because it has three kinds of process parameters: arc welding, laser welding and hybrid welding parameters. In this study, the optimum range of the process parameters were determined by high speed image analysis which could unveil the welding phenomena in laser-arc hybrid welding. The laser-arc hybrid welding was applied for position welding from the flat position to the overhead position and the welding characteristics were investigated.

• Journal of Welding and Joining
• /
• v.26 no.5
• /
• pp.66-73
• /
• 2008

Welding work in pre-erection or erection stage of shipbuilding construction to be carried out in flat and vertical upward position mostly and Electrogas welding(EGW) is actively applied especially for vertical butt joint of thicker steel plate recently. In this study considered how to develope and improve mechanical properties of weld metal and HAZ in high heat input welding processes such as EGW and Electroslag welding(ESW) with its welding equipment in order to extend the application range to the longitudinal members and hatch coaming parts of container ship. Some components of welding system and parameters were modified to get the faster travel speed and reduce weld heat input, and also by adding additional filler rods or tubes increase the amount of deposited weld metal. With the test get some good date can apply to actual fabrication work and recommend items to manufacture welding materials make better. Above all things it's a fruition that to prepare the possibility of application of ESW to shipbuilding construction which fill up the gap of stoppage days of more than 20 years.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.195-202
• /
• 2006

High-speed machining (HSM) with excellent quality and dimensional accuracy has been widely used to create 3D structures of metal and plastics. However, the high-speed machining process is not suitable for the rapid realization of 3D thin-walled product because it consumes considerably long time in fixturing process of a work piece. In this paper, an effective rapid manufacturing process is proposed to fabricate 3D thin-walled products directly using HSM, phase change filling and ultrasonic welding. The filling process is useful to hold the thin-walled product during the machining step. The ultrasonic welding process is introduced to make one piece product from two piece parts that are machined by HSM and filling process. The proposed rapid manufacturing (RM) process has been shown that the RM process enables to fabricate the 3D thin-walled products using ABS plastics and aluminum metals from 3D CAD data to functional parts.

• Journal of Welding and Joining
• /
• v.24 no.5
• /
• pp.37-42
• /
• 2006

The robotic arc welding is widely employed in the fabrication industry fer increasing productivity and enhancing product quality by its high processing speed, accuracy and repeatability. Basically, the bead geometry plays an important role in determining the mechanical properties of the weld. So that it is very important to select the process variables for obtaining optimal bead geometry. In this paper, the possibilities of the Infrared camera in sensing and control of the bead geometry in the automated welding process are presented. Both bead width and thermal images from infrared thermography are effected by process parameters. Bead width and isotherm radii can be expressed in terms of process parameters(welding current and welding speed) using mathematical equations obtained by empirical analysis using infrared camera. A linear relationship exists between the isothermal radii producted during the welding process and bead width.

• Laser Solutions
• /
• v.5 no.1
• /
• pp.33-42
• /
• 2002

In order to investigate the characteristics of the plasma induced by lap-joint CO$_2$ laser welding of automotive steel sheets, the effects of welding speed, shield gas flow rate, gap size, and laser beam defocus to plasma intensity emitted from keyhole have been investigated. The plasma light is measured by fiber and photodiode. Also, the plasma images were captured by the high speed digital camera in 1000frames/sec in order to correlate the plasma light signal with plasma pattern. From the results, it is observed that the difference of the plasma intensity for between the deep penetration and partial penetration exists from 1.2 to 2 times. The plasma light intensity decreased in case of the deep penetration Is observed due to the exhausting of the plasma gas under the sheet. On the other hand, under the conditions of the deep penetration, the plasma intensity is significantly increased by controling the conditions decreasing the penetration depth. It was specially founded that the effect of 0.3mm gap size at partial penetration condition is approximately similar to deep penetration in 0mm gap. It is concluded that the plasma intensity is able to evaluate the penetration depth in lap-joint welding and appears to offer the most straightforward correlation to the welding process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.45-51
• /
• 2013

Friction stir welding using aluminum alloys has been widely applied for transportation vehicles because of the light specific weight, which can be used to obtain sound joint and high mechanical properties. This study shows the effects of rotation speed, welding speed, welding load, and tool shape on defect formation with extruded AA6005, which is used for railway vehicle structures of non-uniform thickness welded by friction stir welding using load control systems. Optical microscopy observations and liquid penetrant testing of each FSW joint were carried out in order to observe defect formation. Two kinds of defects, that of probe wear and that of lack of penetration in the bottom of the welded zone, were observed. In the case of using a taper shaped tool, the defect free zone is very narrow, within 100 kgf; however, in case of using a cylindrical shape tool, the defect free zone is wider.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.36-42
• /
• 2009

In the present day, new performances are demanded for automobile body steel sheet for example, light weight, durability, resistance corrosion and environmental protection. For an improvement of resistance corrosion, European automobile companies developed pre-sealed steel in 1990's. Pre-sealed steel have organic coated layer upper zinc coated layer. Evaluating a resistance spot weldability of pre-sealed steel plate is important because resistance spot welding is used mainly in automobile body joining process. In this study, evaluating a weldability of pre-sealed steel plate was carried out using lobe diagram, dynamic resistance and high-speed image. Usually, Pre-sealed steel has poor weldability than GA steel's. To improve a weldability of pre-sealed steel sheet, pre-current was applied to welding process. Pre-current is applied prior to base-current. In conclusion, the weldability of pre-sealed steel has been improved than GA steel's by applying pre-current.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.9
• /
• pp.1166-1174
• /
• 2000

This work presents a two-dimensional quasi-steady state model to study the fluid flow and heat transfer in high-power density welding process of thin AISI-304 stainless steel plates. The enthalpy method and the finite volume method were used for a numerical analysis of the mushy region phase change as well as the heat flow at the weld pool and the heat-affected zone. The results show that the mushy region distributed around the weld pool becomes wider downstream and the surface heat losses by convection and radiation can be significant factors in welding process especially when a welding speed is relatively low.