• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.19-24
• /
• 2004

The laser welding and its analysis of thin-sheet carbon steels were carried out with high power $CO_{2}$ laser. The main factor of weld quality of laser welding is gap and edge quality. This work was preformed to focus on the gap tolerance problem during laser welding. First, bead on plate welding of thin sheet was examined to investigate the effect of laser welding variables, and to obtain optimum welding condition. Butt welding was also carried out to show the effect of gap on the laser weldability of thin sheet. In order to investigate the effect of gap on formability of welded thin sheet, LDH test was caried out. At high welding speed, the partial penetration was obtained by low heat input. Otherwise, porosity was formed in the bead at low weld speed because of too much heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. The maximum gap tolerance on laser welding was observed to be about 0.2mm. This gap size has good relationship with beam size of laser spot(about 0.3mm). The formability of welded sheet was about $80{\%}$ value of base metal and the gap size has not affected on the formability, although weld quality is dependent on the gap size.

• 한국생산제조학회지
• /
• 제25권5호
• /
• pp.373-379
• /
• 2016

Low carbon steel is usually used as the outer panel with low base metal resistance compared to the inner reinforced panel made with high strength steel, which makes it difficult to form a robust nugget. To overcome welding problems of a dissimilar three-sheet combination made of SGACEN, DP980 and CP1180, a cover plate was inserted between the upper electrode and SGACEN. The quality of the nugget was analyzed by comparing the welding signals and cross sectional images under maximum heat input both with and without the cover plate. To analyze the mechanical of weld properties, a hardness test analysis was conducted. To enhance the reliability of experimental results, temperature distributions were obtained using a simulation program. The method of inserting a cover plate led to a change in the heat input, which induced a larger nugget size between SGACEN and DP980.

• 한국해양공학회지
• /
• 제16권2호
• /
• pp.72-79
• /
• 2002

In this study, time-dependent distributions of temperature and stresses, in the box-column welded from ultra thick plates with center segregation, has been analyzed by the commercial finite element package SYSWELD+, for several types and angles of groove. The major points of investigation are the optimum type and angle of groove that minimize weld stress specially at the center segregation, as well as temperature distribution, residual stresses and changes in the mechanical properties. The results can be summarized as follows; 1) Generally the thermal cycle at the root of groove exhibits relatively rapid cooling pattern, however, most of the other part weldment have a slow cooling pattern in all groove types. 2) Most of the micro-structures of weldment are composed of ferrite and pearlite, meanwhile we could find martensite and bainite locally a the root of the groove. 3) Optimum groove type for high heat input welding of box-column corner is a double groove type, and the optimum angle for the groove is 30~$45^{\circ}$ that minimize deformation and weld stress at the center segregation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.365-372
• /
• 2004

1)고강도강 BOP 시험 결과 강종에 차이 없이 용접속도에 따라 유사한 비드 형상을 가지는 것으로 나타났다. 한편 1.2t 시험편의 적정 용접속도는 $4\~8m/min$으로 나타났다. 2) 용접속도가 빠를수록 비드폭은 작아지며, 경도값은 높게 나타났다. 그리고, 최고 경도값은 강의 성분(Ceq)에 비례하는 것으로 나타났음, 그 결과 TRIP80(Ceq=0.53)의 경우 최고 520Hv이상의 경도값을 가지고 있었다. 3) LDH test 결과 DP강의 모재대비 용접부의 성형성이 약 $90\%$ 정도로 나타났으며, TRIP 및 일반 고강도강은 약 $80\%$의 성형성을 갖는 것으로 확인되었다. 4) He을 보호가스로 사용시 기공의 형성은 크게 억제되었다. 그리고 Ar 사용시에는 기공 형성이 He에 비해 많이 형성되는 것으로 나타나 사용시 주의가 필요한 것으로 보인다. 기공 형성은 TRIP > 60C/45R > DP 순서로 나타나 DP강이 가장 좋은 레이저 용접성을 가지고 있었다.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.80-86
• /
• 2015

The purpose of this study is to establish the predictive method of the angular distortion caused by the line heating process with high frequency induction heating. In order to do it, the heat input model for the high frequency induction heating system was established through comparing the temperature evaluation results obtained by both FEA and experiment. The critical heating conditions to prevent the degradation of the work piece with various thicknesses were identified by FEA and microstructure test results. Under the critical heating conditions, the extensive line heating tests were performed. According to the test results, it was found that the angular distortion behavior of the heated plates could be defined as the function of heat intensity and the rigidity of heated plate. In addition, it was clarified that the angular distortion strongly depended on the size of test specimen such as the length and the width of the heated plate. Based on these results, the predictive equation for the angular distortion was established with the function of heat intensity, bending rigidity and size of heated plate.

• Journal of Welding and Joining
• /
• 제33권5호
• /
• pp.31-34
• /
• 2015

Microstructure and tensile property in the weld heat-affected zone (HAZ) of austenitic Fe-Mn-Al-C low density steels were investigated through transmission electron microscopy analysis and tensile tests. The HAZ samples were prepared using Gleeble simulation with high heat input welding condition of 300 kJ/cm, and the HAZ peak temperature of $1200^{\circ}C$ was determined from differential scanning calorimetry (DSC) test. The strain- stress responses of base steels showed that the addition of V improved the tensile and yield strength by grain refinement and precipitation strengthening. Tensile strength and elongation decreased in the weld HAZ as compared to the base steel, due to grain growth, while V-added steel had a higher HAZ strength as compared than V-free steel.

• 대한기계학회논문집
• /
• 제10권5호
• /
• pp.661-669
• /
• 1986

In this study, the resistance spot welding process of an aluminum alloy was analyzed through the numerical simulation including the electric contact resistance and the heat generation in the electrode. The finite element model was used to solve the electro-thermal responses in weld cycles. The resistance of the contact area was represented as the contact element modeling, but the thermal resistance between the contact surfaces was neglected. Welding tests of Alclad 2024-T3 aluminum alloy were made not only to get the input data for the numerical simulation, but also to compare the numerical results. The contact resistance was determined initially by the contact resistance tests and assumed to decay exponentially up to the solidus temperature. The temperature distributions and dynamic resistance obtained numerically were in good agreement with the experimental results. Numerical results revealed that nugget growth depends mainly on the heat generated in the workpiece and its contact area. The heat generated in the electrode has, however, only a little effect on the nugget growth, and the heat generation in the electrode-workpiece interface is initially high but decrease repidly.

• Journal of Welding and Joining
• /
• 제22권4호
• /
• pp.65-72
• /
• 2004

The aim of this study is to investigate the optimum drawing parameter for BAS111 welded tubes. The BAS111 aluminium alloy tubes with 25.4mm in external diameter and 1.5mm in thickness for heat-exchangers were manufactured by high frequency induction welding with the V shaped convergence angle 6.8$^{\circ}$ and power input 50㎾. With increasing the reduction of area (1.6, 5.8, 11.5, 14.2, 18.5, 22.5%) by drawing, tensile strength was increased and elongation was decreased. With increasing the reduction of area by drawing, hardness in weld metal increased rapidly, while that of base metal increased slowly. In the specimen with the outer diameter smaller than 22mm, hardness of weld metal was higher than that of base metal. The optimum drawing parameter of area reduction was estimated about 15% because of the work hardening of welds.

• 한국태양에너지학회 논문집
• /
• 제35권3호
• /
• pp.65-71
• /
• 2015

A solar thermal simulator is suitable for indoor experiments of solar receivers and reactors when solar insolation and weather conditions are not favorable. Moreover, due to the easy control of electric power input, the solar thermal simulator allows the adjustment of power input incident on solar receivers and reactors and thus the implementation of accurate experiments. We manufactured a solar simulator, which is comprised of three sets of a xenon lamp and an elliptical reflector. In order to serve as a test facility, optical characterization of the solar simulator via radiation heat flux measurement is a critical prerequisite. We applied the flux mapping method to measuring the heat flux distribution of the three lamps. We presented the measurement results in terms of the heat flux distribution, the peak heat flux, the power distribution, the maximum power, and the efficiency for electric power conversion into radiation power. Characterization results show that our solar simulator provides the peak heat flux of $3,019kW/m^2$, the maximum power of 16.9 kW, and the conversion efficiency of 45%, additionally with a 10% operation margin for output increase.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권8호
• /
• pp.1076-1082
• /
• 2012

오늘날 LNG선의 용접에는 아크와 플라즈마가 사용되고 있으나 아크용접은 에너지 밀도가 낮아 후판에 대해서 다층용접이 불가피하며, 고밀도 열원인 레이저 용접에 비하여 용접속도에도 한계가 있다. 따라서 후판 용접시 다층용접에 의한 용접부의 조직적 결함이나 과대 입열로 형성된 열영향부 등의 문제를 해소하기 위하여 키홀용접에 의한 원패스 용접이 고려되고 있다. 키홀용접이 가능한 열원은 레이저, 전자빔, 플라즈마가 있으며, 현재 플라즈마 용접이 아크를 대체하여 LNG선 카고탱크의 멤브레인 용접에 적용되고 있다. 최근에는 멤브레인의 용접에 레이저를 적용하기 위한 많은 연구가 진행 중에 있다. 본 연구에서는 LNG선용 스테인리스강에 대한 파이버 레이저 및 플라즈마 아크 용접의 용접성, 기계적 성질 및 미세조직을 비교하였다. 그 결과 레이저 용접이 더 빠른 용접속도에서 좁은 용접부와 열영향부를 얻을 수 있었다. 따라서 LNG선의 용접에서는 파이버 레이저가 보다 우수한 용접법이라는 것을 알 수 있었다.