• Transactions on Electrical and Electronic Materials
• /
• v.6 no.2
• /
• pp.73-77
• /
• 2005

In this study, we investigated response characteristics of liquid crystal display (LCD) with different operating mode of nematic liquid crystals (NLCs) such as 45 $^{circ} twisted nematic (TN), 67.3 $^{circ} TN and electrical controlled birefringence (ECB) on the rubbed polyimide (PI) surface with side chains. The pretilt angles generated on polyimide surfaces of the three kinds of LCD operating modes were about 12 $^{circ} that was higher than those of conventional TN-LCOs. Also, the Electro-optical (EO) performance of these LCOs showed stable condition. Low transmittance of the 45 $^{circ} TN and 67.3 $^{circ} TN cell on the rubbed PI surface were measured by using low cell gap d. The fast response time in ECB cell among the three kinds of LCD operating modes was achieved. Also, thermal ability of fast 90 $^{circ} TN-LCD was investigated. The threshold voltage and the response time of thermal stressed TN-LCOs showed the same performances on no thermal stressed TN-LCOs. There was little change of value in these TN cells. However, the transmittances of TN-LCOs on the rubbed PI surface decreased while increasing thermal stress time. Therefore, the thermal stability of TN-LCD was decreased by the high thermal stress for the long duration.

• Clinical and Experimental Reproductive Medicine
• /
• v.49 no.2
• /
• pp.149-158
• /
• 2022

Objective: Optimizing culture media for the incubation of immature oocytes is a vital strategy to increase the oocyte maturation rate during in vitro maturation (IVM) programs. This study evaluated the IVM and fertilization rates of human germinal vesicle (GV) and metaphase I (MI) oocytes using two different maturation media (commercial and homemade) with or without growth differentiation factor 9-β (GDF9-β). supplementation. Methods: Immature oocytes from intracytoplasmic sperm injection (ICSI) cycles were collected and assigned to one of two IVM culture media (commercial or homemade; cleavage-stage base). After maturation, MII oocytes were examined under an inverted microscope for the presence of the polar body, zona pellucida (ZP) birefringence, and meiotic spindle (MS) visualization after maturation in four conditions (commercial or homemade medium, with or without GDF9-β. ICSI was done for matured oocytes, and fertilization was confirmed by the visualization of two distinct pronuclei and two polar bodies. Results: No significant differences were found between the two culture media in terms of the time and rate of oocyte maturation or the rate of fertilization (p>0.05). Growth factor supplementation increased the 24-hour maturation rate for both GV and MI oocytes only in homemade medium. The maturation rate after 24 hours was higher for MI oocytes (p<0.05). Similar results were observed for MS visualization and ZP structure in both types of media (p>0.05). Conclusion: Higher rates of oocyte maturation and fertilization were observed after application of homemade medium supplemented with GDF9-β. Therefore, this combination may be recommended as an alternative for clinical IVM programs.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.8-14
• /
• 2023

In this study, basic research was conducted on manufacturing technology of thick-walled light guide a component that controls the light source of automobile lamps. As a preliminary study for manufacturing the final injection molded parts, a model for analyzing the influence of micro patterns on light guides is presented. The optical characteristics of the light guide were analyzed according to the change of the curvature radius of the micro-optical pattern, and the injection molding characteristics of the light guide according to the change of injection molding conditions were analytically evaluated. It was confirmed that the luminance uniformity improves as the R value decreases for changes in the micro-pattern R value, but it was confirmed that there are technical limitations in actual injection mold core processing and high-replication injection molding. Injection molding analysis showed that cooling channel design is very important compared to general injection molding due to thick-wall characteristics and thickness variation. It was also confirmed that the cooling channel has a great influence on the cycle time and birefringence result due to residual stress. As a result of analyzing the influence of filling time, holding condition, and cooling on shrinkage, it was found that the cooling water temperature has a significant effect on the shrinkage of ultra-fine light guide parts, and the holding condition also has a significant effect.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.139-147
• /
• 1994

Orthophosphate crystals were grown by the hydrothermal method and the properties of grown crystals were investigated by means of X-ray diffraction. Vickers hardness tester, etc. The starting powders of $AIPO_4 and GaPO_4 $were prepared as a single phase by the solid state reaction of stoichiometric mixture of $AI_2O_3 or Ga_2O_3$ and $NH_4H_2PO_4$ and the subsequently by the hydrothermal treatment. The hydrothermal conditions for high growth rates of the orthophosphate crystals are as follows: $AlPO_4$ crystal; temperature ranges, between $170$~$200^{\circ}C$; temperatures difference, $15$~$20^{\circ}C;$, hydrothermal solvent, 4m HCl, $GaPO_4 crystal; temperature ranges, between $210 and 240^{\circ}C;$; temperature difference, $25$~$30^{\circ}C; $, hydrothermal solvent, 4m HCl. Morphologies of grown crystals tended to be bounded by (1010), (1011) and (0111) faces at low temperatures, and grew with well developed (0001) faces by increasing the growth temperature. On the other hand, the properties of orthophosphate crystals $(AlPO_4/GaPO_4)$ were as follows: lattice parameters (nm); a=0.494, c=1.094/a=0.490, c=1.105, density (gcm-3); 2.62/3.56, Vickers hardness (Nm^2); $1.02{\times}10^1^0/7.06{\times}10^9$, refractive indices; $ne=1.529{\pm}0.003, no=1.519{\pm}0.003/ne=1.611{\pm}0.006, no=1.599{\pm}0.006, birefringence; {\pm}0.01/{\pm}0.012$, dielectric constant (Fm-1); 6/7.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.3
• /
• pp.93-98
• /
• 2005

The crystal growth of calcite at a low temperature range was carried out by the hydrothermal method using amorphous calcium carbonate which has excellent solubility in water. Amorphous calcium carbonate was prepared by the wet chemical reaction of a stoichiometric mixture of $CaCl_2\;and\;Na_2CO_3$. An important factor was the reaction temperature and time taken in preparation of the amorphous calcium carbonate. From the solubility results calculated by the weight loss method, $NH_4NO_3$ solutions were found to be the most promising solvents to grow calcite single crystals. The hydrothermal conditions for high growth rates of calcite single crystals were as follows: starting material: amorphous calcium carbonate, solvent: 0.01 m $NH_4NO_3$, temperature: $180^{\circ}C$, duration: 30 days. And properties of calcite single crystals were follows: dislocation density: $10^6{\sim}10cm^{-2}$, UV-visible transmittance: about 80% from 190 to 400 nm and birefringence: $0.17{\sim}0.18$. Also, it can be known from the FT-IR results that the absorption peak by injection of $HCO_3^-\;and\;OH^-$ ions was not shown.