• 한국표면공학회지
• /
• 제31권4호
• /
• pp.223-230
• /
• 1998

The separator for a molten carbonate fuel cell(MCFC) is mode of stainless steel and known to the suscepibility to corrosion due to environments of high temperature molten carbonte electrolyte. Considering the sensitization of stainless steel in the temperature range of 425~$815^{\circ}C$, the separator is expected to be sensitized so that the interganular corrosion (IGC) occurs during the cell operation at about $650^{\circ}C$. In this study, EPR(electrochemical potentiokinetic reactivation) technique was examined by relating some elements(mainly C and Cr) to the degree of sensitization of austenitic stainless steels in the molten carbonate salt at $650^{\circ}C$and the possible mechanism of intergranular corrosion was analyzed.

• 한국수소및신에너지학회논문집
• /
• 제31권6호
• /
• pp.596-604
• /
• 2020

Solid oxide electrolysis cell (SOEC) attracts much attention because of its high energy efficiency among many water-electrolysis technologies. SOEC operates at temperatures above 700℃, so that the water required for water-electrolysis must be supplied in the form of steam. When the steam to be supplied to the SOEC is generated by the SOEC system itself, an enormous amount of latent heat is required to vaporize the water, so additional energy must be supplied to the SOEC system. On the other hand, if the steam can be supplied from the outside, a small amount of energy is required to raise the temperature of the low temperature steam, so that the SOEC system can be operated without additional energy supply from outside, which enables efficient water-electrolysis. In this study, we figure out the size of heat exchanger for various steam temperature and effectiveness of heat exchanger, and propose the energy efficiency of the system.

• 대한기계학회논문집B
• /
• 제41권2호
• /
• pp.109-115
• /
• 2017

전산유체해석(CFD) 기법을 이용하여 음극 지지체형 고체산화물 연료전지(SOFC)에 대한 수치해석을 수행하였다. 평판형 구조의 SOFC 에서 가스채널과 리브폭 변화에 따른 성능과 온도균일성에 관한 연구가 이루어졌다. 전산해석 툴로서는 공개소스 전산유체해석 툴박스인 OpenFOAM 을 이용하였다. 수치해석결과, 산소고갈이 일어나지 않는 범위 내에서 가스채널과 리브폭의 증가는 성능과 온도 균일성에 크게 영향을 미치지 않음을 알 수 있었다. 하지만 넓은 리브폭의 사용과 고전류밀도에서의 작동은 산소고갈로 인한 성능저하의 가능성이 있음을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제20권1호
• /
• pp.38-44
• /
• 2009

Recently, the research focused on fuel cell hybrid vehicles (FCHVs) is becoming an attractive solution due to environmental pollution generated by fossil fuel vehicles. The proper energy control strategy will result in extending the fuel cell lifetime, increasing of energy efficiency and an improvement of vehicle performance. Battery state of charge (SoC) is an important quantity and the estimation of the SoC is also the basis of the energy control strategy for hybrid electric vehicles. Estimating the battery's SoC is complicated by the fact that the SoC depends on many factors such as temperature, battery capacitance and internal resistance. In this paper, battery charging time estimated by SoC is studied by using the speed response and current response. Hybrid system is consist of a fuel cell unit and a battery in series connection. For experiment, speed response of vehicle and current response of battery were determined under different state of charge. As the results, the optimal battery charging time can be estimated. Current response time was faster than RPM response time at low speed and vice versa at high speed.

• 한국수소및신에너지학회논문집
• /
• 제22권3호
• /
• pp.305-312
• /
• 2011

The use of a separator to control stack temperature in a molten carbonate fuel cell was studied by numerical simulation using a computational fluid dynamics code. The stack model assumed steady-state and constant-load operation of a co-flow stack with an external reformer at atmospheric pressure. Representing a conventional cell type, separators with two flow paths, one each for the anode and cathode gas, were simulated under conditions in which the cathode gas was composed of either air and carbon dioxide (case I) or oxygen and carbon dioxide (case II). The results showed that the average cell potential in case II was higher than that in case I due to the higher partial pressures of oxygen and carbon dioxide in the cathode gas. This result indicates that the amount of heat released during the electrochemical reactions was less for case II than for case I under the same load. However, simulated results showed that the maximum stack temperature in case I was lower than that in case II due to a reduction in the total flow rate of the cathode gas. To control the stack temperature and retain a high cell potential, we proposed the use of a separator with three flow paths (case III); two flow paths for the electrodes and a path in the center of the separator for the flow of nitrogen for cooling. The simulated results for case III showed that the average cell potential was similar to that in case II, indicating that the amount of heat released in the stack was similar to that in case II, and that the maximum stack temperature was the lowest of the three cases due to the nitrogen gas flow in the center of the separator. In summary, the simulated results showed that the use of a separator with three flow paths enabled temperature control in a co-flow stack with an external reformer at atmospheric pressure.

• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5550-5558
• /
• 2015

최근 환경오염원의 배출이 적고, 에너지 효율이 높은 연료전지에 대한 관심이 높아지고 있으며, 특히 고온동작 연료전지의 경우 대용량 연료전지발전시스템(FCGS, Fuel Cell Generation System)으로 전력계통에 연계되고 있다. 그러나 대용량 FCGS는 계통의 각종외란(불평형전류, 고조파, 서지 등)에 의하여 보호기기의 오동작, 제어소자의 소손현상 및 제어신호 헌팅현상이 발생하여 이에 대한 대책이 요구되고 있는 실정이다. 따라서 본 논문에서는 전력분석장비를 이용하여 대용량 FCGS에서 발생하는 실 계통 문제점을 분석하고, PSCAD/EMTDC, ETAP, P-SIM 소프트웨어를 이용하여, FCGS설비 및 FCGS의 접지계통과 불평형전류, 고조파, 서지와 같은 계통외란현상의 모델링을 수행하였다. 또한, 각 계통외란에 대한 방지대책을 수립하기 위하여, 불평형전류를 줄이기 위한 중성점접지저항기(NGR, Neutral Ground Resister)운용알고리즘, 고조파를 기준 범위 이내로 줄이기 위한 고조파필터 설계알고리즘, 서지로부터 설비를 보호하기 위한 SPD(Surge Protective Device) 운용알고리즘, 적절한 접지계통을 적용하기 위한 접지계통 운용알고리즘을 제안하였다. 이를 검증하기 위하여 상기에서 제시한 모델링을 이용하여, FCGS의 주요 장해요인들을 모의한 결과, 본 논문에서 제안된 대용량 FCGS의 계통외란방지알고리즘의 유용성을 확인하였다.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.243-247
• /
• 2014

Spherical NiO-YSZ particles were synthesized by ultrasonic spray pyrolysis (USP). The morphology of the synthesized particles can be modified by controlling parameters such as precursor pH, carrier-gas flow-rate, and temperature of the heating zone. The synthesized spherical NiO-YSZ particles have rough surface morphology at high carrier-gas flow-rates due to rapid gas exhaustion and insufficient particle ordering. The Ni-YSZ cermet anode synthesized by ultrasonic spray pyrolysis at a flow rate of l L/min, with precursor solution at pH4, showed a higher maximum power density of 256 $mW/cm^2$ compared to a conventionally mixed Ni-YSZ anode (185 $mW/cm^2$) at $800^{\circ}C$. While the area-specific resistance of conventionally mixed Ni-YSZ anodes increases gradually with operation time (indicating performance degradation), the Ni-YSZ anode synthesized by USP does not exhibit any performance degradation, even after 500 h.

• 대한기계학회논문집B
• /
• 제32권9호
• /
• pp.683-694
• /
• 2008

The performance and durability of Polymer Electrolyte Fuel Cells (PEFCs) are strongly influenced by the uniformity of current density, temperature, species distributions inside a cell In order to obtain uniform distributions in them, the optimal design of flowfield must be a key factor. In this paper, the numerical study of land/channel flowfield optimizations is performed, using a multi-dimensional, multi-phase, non-isothermal PEFC model. Numerical simulations reveal more uniform current density and HFR(High Frequency Resistance) distributions and thus better PEFC performance with narrower land/channel width where the less severe oxygen depletion effect near the land region and more uniform contact resistance variation along the in-plane direction are achieved. The present study elucidates detailed effects of land/channel width and assist in identifying optimal flow-field design strategies for the operation of PEFCs.

• 한국세라믹학회지
• /
• 제49권5호
• /
• pp.404-411
• /
• 2012

The reliability of solid oxide fuel cells (SOFCs) particularly depends on the high quality of solid oxide electrolytes. The application of thinner electrolytes and multi electrolyte layers requires a more reliable characterization method. Most of the investigations on thin film solid electrolytes have been made for the parallel transport along the interface, which is not however directly related to the fuel cell performance of those electrolytes. In this work an array of ion-blocking metallic Ti/Au microelectrodes with about a $160{\mu}m$ diameter was applied on top of an ultrathin ($1{\mu}m$) yttria-stabilized-zirconia/gadolinium-doped-ceria (YSZ/GDC) heterolayer solid electrolyte in a micro-SOFC prepared by PLD as well as an 8-${\mu}m$ thick YSZ layer by screen printing, to study the transport characteristics in the perpendicular direction relevant for fuel cell operation. While the capacitance variation in the electrode area supported the working principle of the measurement technique, other local variations could be related to the quality of the electrolyte layers and deposited electrode points. While the small electrode size and low temperature measurements increaseed the electrolyte resistances enough for the reliable estimation, the impedance spectra appeared to consist of only a large electrode polarization. Modulus representation distinguished two high frequency responses with resistance magnitude differing by orders of magnitude, which can be ascribed to the gadolinium-doped ceria buffer electrolyte layer with a 200 nm thickness and yttria-stabilized zirconia layer of about $1{\mu}m$. The major impedance response was attributed to the resistance due to electron hole conduction in GDC due to the ion-blocking top electrodes with activation energy of 0.7 eV. The respective conductivity values were obtained by model analysis using empirical Havriliak-Negami elements and by temperature adjustments with respect to the conductivity of the YSZ layers.

• 한국연소학회지
• /
• 제19권3호
• /
• pp.44-52
• /
• 2014

Solid oxide fuel cell(SOFC) makes electric power using hydrogen or reformed from methane and emits high temperature products that contain flammable species like hydrogen, carbon monoxide and methane which varies with operation condition. SOFC/gas turbine integrated system which uses thermal and chemical energy of the discharges is more efficient than SOFC itself. Burning character of the SOFC products will affect the efficiency and stability of the system. Experiments were conducted to know the characteristics of the flame for two typical composition of SOFC products, i.e. start-up and steady state composition. When coflowing air temperature was higher than $600^{\circ}C$, auto-ignitin occurred for both fuels. Though start-up fuel has higher contents of hydrogen, it makes longer flame than steady state composition. It was inferred that the amount of oxidizer necessary to burn makes this phenomenon. Steady state composition fuel was unstable since it contains lots of water. Nozzle that had 6 holes, distance between each hole was 16.7 times of hole diameter, improved the stability of the flame.