• 한국세라믹학회지
• /
• 제42권10호
• /
• pp.678-684
• /
• 2005

Sick house syndrome comes from VOCs that is harmful to health. To reduce VOCs, the cause of sick house syndrome, several materials have been developed and use. One of this materials, VOCs absorption paint was developed. VOCs absorption paint contains ceramic binder and zeolite powder. In the present study, eco-ceramics paint has been successfully fabricated by high-speed mixer using ceramic binder and filler powders. The eco-ceramics paint thus obtained have a deodorization rate with about 95.7$ \%$ and the bacteria decreasing rate is about 99.6$\%$. Moreover, the eco-ceramics paint showed excellent VOCs interception properties due to effect of ceramics layer and zeolite which exist in surface of paint.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -2
• /
• pp.914-918
• /
• 2000

In this paper, a next generation high speed QPSK transmitter is designed based on 1.8${\mu}$m design rule. The designed transmitter supports the MPEG2-TS coded packed data for the DAVIC standard. Transmitter is composed of the convolutional coder, the shortened Reed-Solomon coder, and QPSK modulator. The coded packets are modulated in APSK with an RC filter. Especially, Galois Field multiplier with a standard basis is designed with the pipelined parallel architecture. Also, in the QPSK modulator, the RC filter and mixer are simplified into the ROM table, which can improve the performance of the transmitter. The total number of gates for the implemented baseband transmitter is 26,875.

• 제어로봇시스템학회논문지
• /
• 제20권11호
• /
• pp.1103-1111
• /
• 2014

The results of control law design for a tilt-rotor unmanned aerial vehicle that has a nacelle mounted wing extension (WE) are presented in this paper. It consists of a control surface mixer, stability and control augmentation system (SCAS), hold mode for altitude / speed / heading, and a guidance mode for preprogram and point navigation which includes automatic take-off and landing. The conversion corridor and the control moments derivatives between the original tilt-rotor and its variant of the nacelle mounted WE were compared to show the effectiveness of the WE. The nacelle conversion of the original tilt-rotor starts when the airspeed is greater than 30 km/h but its WE variant starts at 0 km/h in order to reduce the drag caused by the high incidence angle of the WE. The stability margins of the inner loop are presented with the optimization approach. The outer loops for the hold mode are designed with trial and error methods with linear and nonlinear simulation. The main control parameter for altitude control of the helicopter mode is thrust command and it is transferred to the pitch attitude command in airplane mode. Otherwise, the control parameter for the speed of the helicopter mode is the pitch attitude command and it is transferred to the thrust command in airplane mode. Therefore the speed and altitude hold mode are coupled to each other and are engaged at the same time when an internal pilot engages any of the altitude or speed hold modes. The nonlinear simulation results of the guidance control for the preprogrammed mode and point navigation are also presented including automatic take-off and landing in order to prove the full control law.

• 전자공학회논문지A
• /
• 제33A권6호
• /
• pp.99-107
• /
• 1996

When GPS (global positioning system) is used as synchronous signal in CDMA digital cellular base station system and high speed digital synchronous communication network, antenna cable length is increased, comparing with other GPS application such as positioning or car navigation. In this paper, it is proposed that a type of new GPS antenna system including RF stage for reduction of cable loss in case of long cable.The antenna system with TMPA(truncated-corners microstrip patch antenna) is designed and fabricated because GPS signal has RHCP (right-hand circular polarization), consequently antenna size can be made small size. LNA (low noise amplifier) is designed by using HEMT(high electron mobility transistor)which has lower noise figurae and better AGC characteristics at low voltage than GaAs FET, and we equiped mixer, in GPS antenna unit, which converts from 1575.42MHz to 75.42MHz. As result of comparing between typical system and proposed system when cable length is 60m, 63dB, 55dB and 25dB gain are obtained for RG-316/U, RG-58C/U and RG-213/U, and better characteristics are achieved than typical system as far as cable length is longer.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권6호
• /
• pp.286-295
• /
• 2006

This paper presents a design of a real-time software GPS receiver which runs on a PC. The software GPS receiver has advantages over conventional hardware based receivers in terms of flexibility and efficiency in application oriented system design and modification. In odor to reduce the processing time of the software operations in the receiver, a shared memory structure is used with a dynamic data control, and the byte-type IF data is processed through an Open Multi-Processing technique in the mixer and integrator which requires the most computational load. A high speed data acquisition device is used to capture the incoming high-rate IF signals. The FFT-IFFT correlation technique is used for initial acquisition and FLL assisted PLL is used for carrier tracking. All software modules are operated in sequence and are synchronized with pre-defined time scheduling. The performance of the designed software GPS receiver is evaluated by running it in real-time using the real GPS signals.

• 마이크로전자및패키징학회지
• /
• 제24권1호
• /
• pp.45-50
• /
• 2017

본 연구에서는 Sn-0.7Cu-xZn 무연솔더와 OSP 표면처리 된 솔더접합부의 전단강도를 Zn 함유량에 따라 평가하였다. 다섯 종류의 Sn-0.7Cu-xZn (x=0, 0.5, 1.0, 1.5, 2.0 wt.%) 솔더페이스트를 제작한 뒤, OSP(organic solderability preservative) 표면처리 한 PCB(printed circuit board) 기판의 전극에 리플로우 공정으로 180 um 직경의 솔더볼을 형성하였다. 전단강도는 두 가지 조건의 전단속도(0.01, 0.1 m/s)로 고속전단시험(high speed shear test)을 통해 측정하였고, 고속전단시험 시에 측정된 F-x(Force-distance) curve를 통해 파괴에너지(fracture energy)를 계산하였다, SEM(주사전자현미경, scanning electron microscopy)과 EDS(energy dispersive spectroscopy) 분석을 통하여 단면과 파단면을 관찰하였고, 금속간 화합물(intermetallic compound, IMC) 층을 분석하였다. Zn 함유량이 증가함에 따라 금속간 화합물 층의 두께는 감소하였고, Zn 함유량이 0.5 wt.%일 때 가장 높은 전단 강도(shear strength)를 나타내었다. 전체적으로 높은 전단속도 조건의 전단강도 값이 낮은 전단속도 조건의 전단강도보다 높았다.

• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.392-399
• /
• 2009

The paper concerns the description of the step by step development process of the new fixed blade runner called "Mixer" suitable for the uprating of the Francis turbines units installed at the older low head hydropower plants. In the paper the details of hydraulic and mechanical design are presented. Since the rotational speed of the new runner is significantly higher then the rotational speed of the original Francis one, the direct coupling of the turbine to the generator can be applied. The maximum efficiency at prescribed operational point was reached by the geometry optimization of two most important components. In the first step the optimization of the draft tube geometry was carried out. The condition for the draft tube geometry optimization was to design the new geometry of the draft tube within the original bad draft tube shape without any extensive civil works. The runner blade geometry optimization was carried out on the runner coupled with the draft tube domain. The blade geometry of the runner was optimized using automatic direct search optimization procedure. The method used for the objective function minimum search is a kind of the Nelder-Mead simplex method. The objective function concerns efficiency, required net head and cavitation features. After successful hydraulic design the modal and stress analysis was carried out on the prototype scale runner. The static pressure distribution from flow simulation was used as a load condition. The modal analysis in air and in water was carried out and the results were compared. The final runner was manufactured in model scale and it is going to be tested in hydraulic laboratory. Since the turbine with the fixed blade runner does not allow double regulation like in case of full Kaplan turbine, it can be profitably used mainly at power plants with smaller changes of operational conditions or in case with more units installed. The advantages are simple manufacturing, installation and therefore lower expenses and short delivery time for turbine uprating.

• 한국항행학회논문지
• /
• 제1권1호
• /
• pp.23-34
• /
• 1997

다채널 디지털 GPS 수신기를 구현하기 위하여 RF-to-IF엔진 (엔진 1), 신호처리 엔진 (엔진 2), 항법 소프트웨어를 개발하였다. 고속 SiGe HBT률 이용한 LNA, 믹서, VCO 등의 하이브리드 IC를 COB형태로 구현하여 엔진 1 보드에 부착하였다. 6채널 디지털 상관기를 클락 및 마이크로프로세서 인터페이스와 함께 Altera Flex 10K FPGA 및 ASIC 기술로 구현하였다. 항법 소프트웨어는 GPS 신호의 트래킹 및 획득을 위한 상관기 제어, 메시지 저장, 위치 계산 등을 수행한다. 개발된 GPS수신기는 단일 채널 신호를 발생하는 STR2770 시뮬레이터를 이용하여 테스트하였는데, 성공적인 항법 신호획득 및 위치 계산 결과를 확인하였다.

• 한국컴퓨터정보학회논문지
• /
• 제7권4호
• /
• pp.115-120
• /
• 2002

본 논문은 Field Programmable Gate Array (FPGA)와 디지털 신호처리 소자를 이용한 IS-95 CDMA신호 처리기 FPGA와 고속의 ADC/DAC를 이용한 기저대역과 중간주파수(IF)의 디지털 변환기 그리고 주파수 상·하향 변환기를 구현하였다. IS-95 CDMA 채널 처리기는 짧은 PN 코드 발생기와 왈쉬 코드 발생기로 파일롯 채널의 신호를 발생시킨다. 디지털 IF는 FPGA, 디지털 송·수신 신호처리 소자와 고속의 ADC/DAC로 구성하였다. 주파수 상·하향 변환기는 필터, 믹서, 디지털 감쇠기와 PLL로 구성되어 중간주파수(IF)와 RF 주파수를 변환하였다. 이 구현된 시스템은 IS-95 CDMA 기지국 장비 등에 장착할 수 있다.

• 한국통신학회논문지
• /
• 제31권1A호
• /
• pp.58-64
• /
• 2006

900 MHz 대역의 ISO-18000-6B형 표준의 수동형 RFID 리더용 트랜시버를 개발하였다. 송신부의 ASK 변조회로는 GaAs SPST 스위치를 이용하여 고속 저전력 변조 회로로 구성하였으며, 수신부에서는 이중 평형 믹서와 비교기를 이용하여 복조회로를 구성하였다. LO 신호에 대한 우수 고조파 성분들을 억압하고 수신기의 선형성을 향상시키기 위하여 연산 증폭기를 이용한 복조회로와 전압 플로워 및 비교기를 사용하여 회로의 복잡성을 개선하였다. 개발된 트랜시버는 $900{\sim}916\;MHz$ 대역에서 6 dBi의 상용 안테나를 사용하여 5 m의 인식 거리를 얻었다.