• 한국산학기술학회논문지
• /
• 제9권6호
• /
• pp.1529-1534
• /
• 2008

최근, 교반기는 화학물질의 교반 및 탈포를 위해 디스플레이, 반도체 업체에서 광범위하게 사용되고 있다. 교반기는 일반적으로 축, 교반조, 감속기어 및 구동 모터로 구성되어 있다. 교반기 설계시의 주요 사항은 회전시의 동적 특성을 평가하는 것이다. 회전시의 동적특성은 진동, 소음 및 열방출로 나타난다. 본 논문은 고속 교반기의 동적 특성을 실험적으로 규명하였다. 진동을 유발하는 주 인자는 회전체의 불균형에 기인한 것임을 알 수 있었으며, 교반 용기 부위의 온도가 전체온도에서 상대적으로 제일 높음을 알 수 있었다.

• 상하수도학회지
• /
• 제13권3호
• /
• pp.107-115
• /
• 1999

The general objectives of this study are to develop a new biofilm reactor equipped with agitating mixer and to evaluated the treatment efficiency of the reactor. The experimental tests were conducted to estimate the oxygen transfer rate of agitating mixer system. Results are as follows. 1. The oxygen transfer coefficient, KLa, was $8.94hr{-1}$ and $7.50hr{-1}$ at 500rpm and 250rpm of agitating mixer speed, respectively. When the agitating mixer was used in the biofilm reactor, 22.5% and 18.8% of oxygen transfer rates were increased at 500rpm and 250rpm, respectively. 2. The removal rate of BOD and CODcr was decreased by 5.0% when the agitating mixer speed was varied from low (250rpm) to high level (500rpm). 3. The concentration of attached biomass had a difference of 5.0% to 7.3%, whereas that of suspended biomass had a difference of about 15.0%, depending upon variation of the agitating mixer speed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.445-452
• /
• 2001

Generally, OPC(ordinary portland cement) is used for grouting in Korea, and bentonite has usually been added to prevent the deposition of cement particles. The dispersion of CB(cement bentonite) grout is influenced by variable factors i.e. water to cement ratio, particle size of cement, kind of bentonite, adding volume, methods of adding, viscosity of CB grout materials and curdling time. Among variable factors, the viscosity of CB grout materials is influenced by the dispersion, and dispersion is improved as increasing the mixing speed. In this paper, described a suitable mixing speed of the High Speed Mixer in field, engineering characteristics of CB grout materials vary with the water to cement ratio and the mixing speed as well as confirming the state of dispersion.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.549-552
• /
• 2006

Generally the ultra-high strength steel reinforced concrete has rich mix composition composed of high-strength type mineral admixtures and as a result of very low water-binder ratio(about under w/b=25%), it reveals ultra-high compressive strength(about over 100Mpa). Also, in order to obtain sufficient toughness after construction, we usually mix a large quantity steel fiber with ultra-high strength steel reinforced concrete therefore we must use proper mixer for workability. When we make the ultra-high strength steel reinforced concrete we need more long mixing time or much super-plasticizer than when we manufacture normal concrete. These bring about economical problems and performance deterioration. Therefore, in this study, in order to manufacture easily ultra-high strength steel reinforced concrete we develope a dedicated mixer for ultra-high strength steel reinforced concrete with high speed type. It carried out the examination for comparison between the dedicated and general type mixer, the analysis and counterplan of the point at issue when we manufacture ultra-high strength steel reinforced concrete by the dedicated mixer.

• 한국정밀공학회지
• /
• 제30권5호
• /
• pp.544-551
• /
• 2013

Recently high speed mixer, which is mixing, grinding, dispersion for liquid-liquid material, has been widely used several industries such as food, cosmetics, pharmaceuticals, fine chemicals, electronic material. This high speed mixer has a core element part called particle separation device. Particle separation device, which makes mixed liquid and liquid material using shear forces from a rotor and a stator, is a decisive factor in the distributed parts. In this study, we examined the velocity distribution of the two models of particle separation device using computation fluid dynamics, so that we were able to see the difference of the velocity distribution according to the shape. Also, by experiment, we observed that the use of rotor-screen type is deemed more suitable in case of accurately considering the effect of improving of the dispersibility through the circulation of the future.

• 항공우주시스템공학회지
• /
• 제13권5호
• /
• pp.39-48
• /
• 2019

회전-고정자 혼합기 내의 난류 유동은 고속으로 회전하는 회전자와 고정자의 상호작용에 의해 발생되는 전단특성을 기반으로 한다. 본 연구에서는 유화연료 관련 회전-고정자 혼합기 시제품 모델에서 회전자와 고정자간의 상호작용에 의한 비정상상태 유동 특성 분석을 ANSYS FLUENT $k-{\varepsilon}$ (RKE) 난류 모델을 MRF 및 SMM에 적용하여 수행하였다. 회전자와 고정자의 경계에서 발생하는 유동 입자들의 거동과 전단 특성 그리고 설계 파라미터에 따른 속도분포와 난류와류소산 등의 경향을 전산유체역학 해석을 통해 예측 비교하여 모델의 효율성을 검증하였다.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2002년도 종합학술발표회 논문집 Vol.12 No.1
• /
• pp.16-20
• /
• 2002

This paper describes the resistive FET mixer with low IF for the 4-Ch DBF(Digital Beam Forming) receiver with LNA(Low Noise Amplifier). This DBF receiver based on the direct conversion method is generally suitable for high-speed wireless mobile communications. A radio frequency(RF), a local oscillator(LO) and an intermediate frequency(IF) considered in this research are 2.09 ㎓, 2.08 ㎓ and 10㎒, respectively. The RF input power, LO input power and Vgs are used -10㏈m, 6㏈m and -0.4 V, respectively. In the 4-Ch resistive FET mixer with LNA, the measured IF and harmonic components of 10㎒, 20㎒, 2.09㎓ and 4.17㎓ are about -12.5 ㏈m, -57㏈m, -40㏈m and -54㏈m, respectively. The IF output power observed at each channel of 10㎒ is about -12.5㏈m and it is higher 27.5 ㏈m than the maximum harmonic component of 2.09㎓. Each IF output spectrum of the 4-Ch is observed almost same value and it shows a good agreement with the prediction.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.1-6
• /
• 2013

In many technical fields including electronics and display manufacturing processes, properties of coating liquids could be greatly enhanced by adding nanopowders and it requires efficient mixing techniques to achieve uniform dispersion of nanoparticles in liquids. This paper presents the three-dimensional CFD simulations on the flowfields of a highly viscous liquid in the large scale industrial mixer of impeller type. The effects of several important design and operation parameters such as impeller geometry, rotational speed, and degree of liquid viscosity are investigated to appreciate the mixing performance by examining the computational results for flow pattern of rotationally stirred liquid of high viscosity in the mixer.

• Journal of electromagnetic engineering and science
• /
• 제2권2호
• /
• pp.117-123
• /
• 2002

This paper describes the design for the resistive FET mixer with low If for the 4-Ch DBF(Digital Beam Forming) receiver This DBF receiver based on the direct conversion method is generally suitable for high-speed wireless mobile communications. A radio frequency(RF), a local oscillator(LO) and an intermediate frequency(If) considered in this research are 2.09 GHz, 2.08 CHz and 10 MHz, respectively. This mixer is composed of band pass filter, a low pass filter and a DC bias circuit. Super low noise HJ FET of NE3210S01 is considered in design. The RE input power, LO input power and Vcs are used -10 dBm, 6 dBm and -0.4 V, respectively. In the 4-Ch resistive FET mixer, the measured If and harmonic components of 10 MHe, 20 MHz and 2.087 CHz are about -19.2 dBm, -66 dBm and -48 dBm, respectively The If output power observed at each channel of 10 MHz is about -19.2 dBm and it is higher 28.8 dBm than the maximum harmonic component of 2.087 CHz. Each If output spectrum of the 4-Ch is observed almost same value and it shows a good agreement with the prediction.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.929-930
• /
• 2012