• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.919-928
• /
• 2010

연속주조 시에 폭변경 속도를 향상시키기 위해 폭조정의 4 가지 패턴에 대해 연구하였다. 주요 사항은 폭변경 장치의 구동력을 최소화하고, 몰드 내의 응고막의 변형해석 모델을 개발하고, 폭변경 속도 상승을 제한하는 주요인자를 도출하는 것이다. 폭변경 실험을 근간으로 4 개 패턴의 주요 특징을 도출하였고, 각 패턴에 대한 힘을 비교하였다. 실험은 각 패턴의 구동력 비교를 위해 동일한 주조속도에서 수행하였다. 응고막변형 해석모델의 변수를 조정하기 위해 실험결과를 모델에 적용하였다. 폭변경 속도를 상승시키고, 구동력을 저감시키기 위해 패턴의 변수를 제어하였다. 가장 효율적인 패턴은 고속패턴이었으며, 구동력을 저감하기 위한 주요인자는 구동장치가 이동할 때의 기울기였다.

• 한국기계가공학회지
• /
• 제6권1호
• /
• pp.43-49
• /
• 2007

Multi-function and miniaturization of the medical equipment and tele-communication systems need small and high precision machined parts. For the economic machining of the small size workpiece it should be machined by small and high precision machine tools with high speed machining. The belt type driving system in turning lathe has a limitation of spindle speeds because of the vibrations from driving mechanism, built-in type of driving mechanism is used to reduce the vibration. However, the main spindle of the built-in motor is connected directly to the motor, so the heat generation of the motor and bearing makes bad influence of the accuracy of machine tools. In this study, the analysis of heat generation from motor and bearings supporting main spindle and experiment were carried out. The results of theoretical simulation of temperature and deformation of the main spindle are good agreement with those of measured.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.23-31
• /
• 2015

Stainless steel is used in automobile muffler and exhaust systems. However, in comparison with other steels it has a high thermal expansion rate and low thermal conductivity, and undergoes excessive thermal deformation after welding. To address this problem, we evaluated the use of arc brazing in place of welding for the processing of an exhaust system, and investigated the parameters that affect the joint characteristics. Muffler parts STS439 and hot-dipped Al coated steel were used as test specimens, and CuAl brazing wire was used as the filler metal for the cold metal transfer (CMT) welding machine, which is a low heat input arc welder. In addition, a Box-Behnken design of experiment was used, which is a response surface methodology. The main process parameters (current, speed, and torch angle) were used to determine the appropriate welding quality and the mechanical properties of the brazing part was evaluated at the optimal welding condition. The optimal processing condition for arc brazing was 135A current, 51cm/min speed and $74^{\circ}$ torch angle. The process was applied to an actual exhaust system muffler and the prototype was validated by thermal fatigue, thermal shock, and endurance limit tests.

• 소성∙가공
• /
• 제21권7호
• /
• pp.441-446
• /
• 2012

A sequential coupled field analysis of electromagnetic free bulging was performed by using FEM. A 2D axi-symmetric electromagnetic model based on the magnetic vector potential is proposed for the calculation of magnetic field and Lorentz's forces. The Newmark integration method is used to calculate the transient dynamic plastic deformation of sheet during free bulging. In the finite element model, the effect of sheet deformation on the electromagnetic field analysis is taken into consideration. In order to confirm the sequential electromagnetic-mechanical coupling analysis, an experiment with an electromagnetic forming apparatus was conducted. The results showed that the final bulge height of the sheet predicted from the proposed method is in good agreement with experimentally measured height.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.566-569
• /
• 2008

Recently, the biolistic process is emerging as an effective needle-free drug delivery technique to transfer adequate concentrations of pharmacologic agents to soft living tissues with minimum side effects. We have started developing an effective method for delivering drug coated particles using laser ablation. A thin metal foil with deposited micro-particles on one side is irradiated with laser beam on the opposite side so that a shock wave is generated. This shock wave travels through the foil and is reflected, which causes and instantaneous deformation of the foil. Due to such a sudden deformation, the micro-particles are ejected at a very high speed. Here we present the experimental results of direct and confined laser ablation, which correspond to the initial stage of the whole experiment.

• Advances in Computational Design
• /
• 제4권1호
• /
• pp.33-41
• /
• 2019

In this study, 2-mm Al/Cu bimetallic laminates were produced using asymmetric roll bonding (RB) process. The asymmetric RB process was carried out with thickness reduction ratios of 10%, 20% and 30% and mismatch rolling speeds 1:1, 1:1.1 and 1:1.2, separately. For various experimental conditions, finite element simulation was used to model the deformation of bimetallic Al/Cu laminates. Specific attention was focused on the bonding strength and bonding quality of the interface between Al and Cu layers in the simulation and experiment. The optimization of mismatch rolling speed ratios was obtained for the improvement of the bond strength of bimetallic laminates during the asymmetric RB process. During the finite element simulation, the plastic strain of samples was found to reach the maximum value with a high quality bond for the samples produced with mismatch rolling speed 1:1.2. Moreover, the peeling surfaces of samples around the interface of laminates after the peeling test were studied to investigate the bonding quality by scanning electron microscopy.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.84-92
• /
• 2005

This paper is concerned with optimum design of a center-pillar assembly induced by the high-speed side impact of the vehicle. In order to simulate deformation behavior of the center-pillar assembly, simplified finite element model of the center-pillar and a moving deformable barrier are developed based on results of the crash analysis of a full vehicle model. In optimization of the deformation shape of the center-pillar, S-shaped deformation is targeted to guarantee reduction of the injury level of a driver dummy in the crash test. Tailor-welded blanks are adopted in the simplified center-pillar model to control the deformation shape of the center-pillar assembly. The thickness of each part which constitutes the simplified model is selected as a design parameter. The thickness of parts which have significant effect on the deformation mechanism are selected as design parameters with sensitivity analysis based on the design of experiment technique. The objective function is constructed so as to minimize the weight and lead to an S-mode deformation shape. The result shows that the simplified model can be utilized effectively for optimum design of the center-pillar members with remarkable saving of computing time.

• 한국지반신소재학회논문집
• /
• 제11권4호
• /
• pp.1-8
• /
• 2012

본 논문에서는 실대형 실험을 통해 블록식 보강토옹벽에서 보강재의 타입에 따른 수평토압, 변위, 보강재의 변형률의 특성을 비교하였다. 본 연구를 통해 보강재의 타입에 따라 토압과 변위관계에서 서로 다른 거동특성을 보이고 있으며, 보강토체 내에 배치된 보강재가 연직토압 감소 및 변체변위 억제 효과 등 보강 성능이 있음을 확인할 수 있었다. 수평토압은 보강재의 특성과 변형에 따라 상단부와 하단부에서 주동토압이나 정지토압보다 크게 발생할 수 있으며, 수평토압과 벽체변위는 서로 상관성이 매우 높은 관계를 가지는 것으로 나타났다. 블록식 보강토 옹벽에서 보강재의 등고변형률선 분포는 중앙부분에서 가장 큰 변형이 발생하는 것을 확인하였다.

• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.43-53
• /
• 1990

The transient temperature distribution in the continuous friction welding 304 stainless steel bars is investigated by experimental and analytical methods. It is calculated by F.D.M. (finite difference method). The heating pressure, the rotational speed and friction coefficient obtained from experiment are used to determine the heat input at the contacting surface. Thermal properties of the workpiece are the function of temperature. The calculated temperature is well coincided with the measured value. The grain size at weld interface is extremely small due to the severe plastic deformation at high temperature, and result of this refined zone reveals higher hardness value. Because the HAZ is very narror about 2-3 mm, welding defects do not occure.

• 한국기계가공학회지
• /
• 제5권2호
• /
• pp.56-64
• /
• 2006

Rapid progress in many branches of technology has led to a demand on new materials such as high strength light weight alloys, powdered alloys and composite materials. The hydrostatic extrusion is essentially a method of extruding a clad rod through a die. In order to investigate the effect of the process conditions such as friction heat, deformation and clad thickness on the clad extrusion process, viscoplastic finite element simulations were conducted. A specific model for theoretical analysis used in this study is The single scalar variable version of Hart's model. An experiment also has been carried out using 1.5MN hydrostatic extruder with variable speed ram, LVDT and load cell for comparison. It is found that the hydrostatic extrusion pressure considering the effect of heat dissipation in this theoretical work was closer to the experimental pressure than the isothermal hydrostatic extrusion pressure.