• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.48-57
• /
• 1996

A study was made to examine the characteristics of base metal and stress relief cracking(SRC) of heat affected zone(HAZ) for HY-100 and Cu-bearing HSLA-100 steels. The Gleeble thermal/mechanical simulator was used to simulate the SRC/HAZ. The details of mechanical properties of base plate and SRC tested specimens were studied by impact test, optical microscopy and scanning electron microscopy. The specimens were aged at $650^{\circ}C$ for HSLA-100 steel and at $660^{\circ}C$ for HY-100 steel and thermal cycled from $1350^{\circ}C$ to $25^{\circ}C$ with a cooling time of $\Delta$t_${800^{circ}C/500^{circ}C}$=21sec. corresponds to the heat input of 30kJ/cm. The thermal cycled specimens were stressed to a predetermined level of 248~600MPa and then reheated to the stress relief temperatures of $570~620^{\circ}C$. The time to failure$(t_f)$ at a given stress level was used as a measure of SRC susceptibility. The strength, elongation and impact toughness of base plate were greater in HSLA-100 steel than in HY-100 steel. The time to failure was decreased with increasing temperature and/or stress. HSLA-100 steel was more susceptible to stress relief cracking than HY-100 steel under same conditions. It is thought to be resulted from the precipitation of $\varepsilon$-Cu phase by dynamic self diffusion of solute atoms. By the precipitation of $\varepsilon$-Cu phase, the differential strengthening of grain interior relative to grain boundary may be greater in the Cu-bearing HSLA-100 steel than in HY-100 steel. Therefore, greater strain concentration at grain boundary of HSLA-100 steel results in the increased SRC susceptibility. The activation energies for SRC of HSLA-100 steel are 103.9kcal/mal for 387MPa and 87.6kcal/mol for 437MPa and that of HY-100 steel is 129.2kcal/mol for 437MPa.

• 한국화재소방학회논문지
• /
• 제16권4호
• /
• pp.15-19
• /
• 2002

BaTiO$_3$계 PTC 서미스터의 조성개발을 위해 (Ba$_{0.95-x}$S $r_{0.05}$C $a_{x}$)$TiO_3$-$0.01TiO_2$-$0.01SiO_2$-$\alpha$MnCO_3$-$\beta$Nb_2$o_{5}$와 같은 실험조성식을 설정한 후 최적 조건하에서 적층형 PTC시편을 제작하여 실험하였다. 실험 결과, 시편제조시의 최적 소결온도와 냉각속도는 각각 $1350^{\circ}C$-2 hour및 $100^{\circ}C$/h였다. 또한 상온저항을 낮추는 효과가 있는 Dopant로서의 Ca와 Mn 그리고 피크(peak)저항값을 높일 수 있는 Nb를 Ca:5 mol%, Mn:0.08 mol%, Nb:0.18 mol%로 함으로써 비교적 낮은 상온저항과 높은 피크(peak)저항 및 양호한 온도계수 특성이 나타났으며, 화재감지센서로서의 활용 가능성을 확인하였다.다.다.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.97-103
• /
• 1999

Ships, structures on the ocean, bridges, and other structures tend to be large by the development of industry. These ultra thick plate were welded with large heat input, which causes welding stresses, deformation and buckling, so it has to be considered the weld design, safety, reliability. The welded residual stresses were produced and redistributed due to the effect of large heat input. The mechanical phenomenon has not been surely identified yet. In spite of the lack of the study on the box column, there are various types of steel frame such as I type, H type, + type and $\bigcirc$ type, used in high story building. In this study, we performed computer simulation with two dimensional heat conduction and plane deformation thermal elasto-plastic finite element computer program as changing the plate thickness to 100mm, 150mm and groove angle to $60^{\circ}C$, $45^{\circ}C$, $30^{\circ}C$ of corner joint in box column. And then, to identify mechanical phenomenon such as the phenomenon of thermal distribution, welding residual stresses and deformation and to decide optimum groove angle and welding condition. The main conclusion can be summarized as follows: 1) Since the groove angle has became cooling down rapidly due to its smaller value, the temperature slope was steeped somewhat. 2) The tensile stress within the welding direction stresses was somewhat decreased at the weld metal and HAZ, increasing of the groove angle. 3) The local stress concentration of the groove angle $60^{\circ}C$ was appeared smaller than groove angle $30^{\circ}$.

• 공업화학
• /
• 제16권4호
• /
• pp.570-575
• /
• 2005

하수방류수 살균 소독에 이용되는 UV 램프를 기존의 전극용보다 효율을 높이고 수명이 긴 무 전극 UV 램프를 제작하고 그 성능을 알아보았다. 우선 활성물질을 변화시키면서 제조한 램프의 UV 강도 및 온도의 변화를 실험 하였다. 그 결과 활성물질이 Hg/In의 무게비 95/5로 만든 램프를 250 min간 운전한 결과 UV 강도 $300{\mu}W/cm^2$ 및 온도 $200{\sim}250^{\circ}C$로 가장 안정적인 결과를 나타내었다. 그러나 무전극 램프를 장시간 발광시켰을 경우 램프의 온도가 상승하기 때문에 이를 방지하기 위해 실제 하수처리공정에 적용할 수 있는 냉각이 가능한 이중관 형태로 제작하여 UV 강도와 온도 변화특성을 알아보았다. 또한 제작된 무전극 UV lamp를 하수 방류수의 살균 소독을 위하여 대장균(E-coli.)으로 실험한 결과에서도 99.9% 이상의 살균효율을 보였다.

• 한국태양에너지학회 논문집
• /
• 제34권5호
• /
• pp.73-80
• /
• 2014

This study introduces and analyzes the geothermal energy availability in Non-active volcanic region. Jeju island in Korea is situated in non-active volcanic region. The island is composed of rock with high pore and clinker, scoria geological layer formed by volcanic activity about two million ago. Volcanic geological layers with porous characteristics have air, vapor, water and a underground structure through which air or water can move easily. For this reason, it is probable that the mechanism of energy acquisition is by convective heat transfer. For this presumption, the availability of underground air as energy source has been studied here through theoretical analysis and experimental data. The energy output of our system ranged from 2,485,076 kJ/day to 4,060,978 kJ/day monitored using variable velocity air flow controller. Our system has capability to be a reliable energy source irrespective of environmental changes. Consequently, underground air can be utilized for energy source and provide the optimal design of heating/cooling system.

• 대한환경공학회지
• /
• 제28권5호
• /
• pp.543-548
• /
• 2006

본 논문은 Ba-Ti-Si형 고유전체 세라믹촉매방전관의 오존발생특성에 관해 연구이다. 기본적인 실험조건은 방전관의 외부직경 52 mm, 방전관 길이 350 mm, 전원 주파수 900 Hz, 냉각수 온도 $25^{\circ}C$, 유량 5, 10, 20 L/min, 방전관 내부 압력 1.2, 1.4, 1.6 atm 그리고 방전관과 전극 사이는 0.4, 0.6, 0.8 mm이다. 그리고 실험결과의 특성들은 오실로스코프상에 나타난 리사쥬 도형의 값을 환산한 소비전력으로 유량 20 L/min, 방전간격 0.6 mm, 압력 1.6 atm 그리고 반응기 내의 무성방전에 사용된 소비전력 150 W에서 최대 오존발생효율 175 g/kWh를 얻을 수 있었다. 그리고 최대 오존발생효율 영역은 1.6 atm 이하의 압력에서는 유량 20 L/min 이하에서 측정되었다. 또한 최대 오존발생효율의 영역은 1.6 atm 이상의 압력에서는 유량 20 L/min 이상인 경우에 오존발생 효율이 높아졌다.

• 한국주거학회논문집
• /
• 제20권6호
• /
• pp.39-46
• /
• 2009

It has been a serious problem to consume the energy of apartment while increasing to use of heating & cooling System because of residence environmental upgrades. Great attention has been shown to the problem of the rental apartment, so there are few reports of energy consumption about the rental apartment in korea. To solve the lack of housing, our country has supplied an enormous volume of apartments, and these days it occupies 75% of our buildings. As apartments occupy most of our housings, the rate of energy usage from them are also high. On this, setting apartment energy reduction as a target, by researching the actual conditions of energy consumption and drawing a basis data, we can apply this as a way of saving energy, rationalization of the scale of energy supply facilities and a standard when planning facilities. To grasp the present condition of energy usage of the urban rental apartment, this research analysed the use of electricity, gas and water monthly and annually of a rental apartment that is located in Daegu. The results showed that in 2003 the electricity usage was 1,198MWh but 1,315MWh in 2007, which means 9% of electricity usage increases every year. The average of water usage was $85,072\;m^2$ per year and typical energy consumption unit was $604.2\;MJ/m^2$ on $74.4\;m^2$ of area and $448.8\;MJ/m^2$ on $105.8\;M^2$. By showing the usage of energy and water of the urban rental apartment, understanding the tendency and preparing an typical energy consumption unit standard through this research, apartments should use energy more efficiently.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.752-757
• /
• 2010

소형위성발사체 (KSLV-I)의 발사 준비에는 다양한 규격의 질소 가스 및 초저온 액체 질소가 소요된다. 발사대 질소 공급 시스템은 고압의 질소 가스 생성, 추진제 충전 후 발사 대기 중인 발사체의 보호를 위한 공간 퍼지용 질소 가스 생성, 연료 및 산화제의 냉각을 위한 액체 질소 공급 기능을 수행하기 위하여 개발되었다. 대기 환경 조건에 따라 열전달 특성이 민감하게 변화하는 대기식 기화기의 운용 불안정성을 제거하기 위해 기화기의 병렬 설치 및 교대 운용 절차를 도입하였다. 이를 통하여 기후조건에 상관없이 항시적으로 운용이 가능한 시스템을 개발하였으며, 소형 위성 발사체의 비행 시험을 위한 발사대 운용을 성공적으로 수행하였다.

• 동아시아식생활학회지
• /
• 제26권6호
• /
• pp.517-530
• /
• 2016

This research was conducted on Seoul region elementary, middle, and high school nutritionists to analyze execution conditions of HACCP control standards, focusing on PHF and CCP 3~CCP 7, in order to determine more efficient methods for school meals' sanitation system settlement. All surveys were distributed and collected via email. A total of 305 survey papers were collected, and 300 school results were analyzed. The following percentage of nutritionists perceived the following foods as potentially hazardous foods(PHF): raw or cooked animal foods (94.7%), blossomed seed products (93.7%), packed pickled radish (36.7%), unopened mayonnaise (30.2%), and unopened snails & corn cans 54.8%. Exactly 51.2% of nutritionists believed that foods were properly supplied via CCP 3's food quality standard. Exactly 33.9% of nutritionists answered that they had never corrected the digital thermometer since there were no issues with the CCP 4's digital thermometer correction frequency level. As for CCP 5's chroline disinfection of green vegetables, 57.1% of nutritionists answered that vegetables were slightly softened while 36.2% said there were no changes at all. According to the nutritionists, the most difficult execution level of CCP levels (excluding CCP 3, CCP 4) was CCP 7 (37.1%), CCP 6 (16.4%), and CCP 2 (16.4%). For the above results, proper training/education must be enforced so that nutritionists can have a clear notion of the PHF. A solution must be developed enhancing the execution of CCP 4's digital thermometer correction frequency level. For CP 5's chroline disinfection of green vegetables, food characteristics must be considered to suggest an appropriate number and method of cleansing. Furthermore, cooking employees are needed that properly use and manage cooling & heating equipments to maintain heated foods above $57^{\circ}C$ under the CCP 7 standard.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.713-721
• /
• 2004

Variable air intake and variable exhaust nozzle of hypersonic engines are designed and tested in this study. Dimensions for variable geometry air intake, ram combustor and variable geometry exhaust nozzle are defined based on the requirements of a pre-cooled turbojet engine. Hypersonic Ramjet Engine is designed as a scaled test bed for each component. Actuation forces of moving parts for variable intake and variable nozzle are reduced by balancing the other force in the opposite direction. A demonstrator engine which includes variable intake and variable nozzle is designed and the components are fabricated. Composite material with silicone carbide is applied for high temperature parts under oxidation environment such as leading edge of the variable intake and combustor liner. Internal cooling structure is adopted for both moving and static parts of the variable nozzle. Pressure recovery and mass capture ratio of the variable intake at Mach 5 is obtained by a hypersonic wind tunnel test. Flow characteristics of the variable nozzle are obtained by a low temperature flow test. Wall temperature and heat flux of the nozzle at Mach 3 is obtained by a firing test. As results, the intake and the nozzle are proved to be used at designed pressure and temperature environment.