• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.2
• /
• pp.153-159
• /
• 2010

This work focuses on finding a method to reduce the noise of a hermetic reciprocating compressor during start-up using an acoustical analysis. The noise of compressor during start-up, which is a higher level than that of a normal operating condition, has transient and non-stationary characteristics. The acoustical analysis of compressor cavity is performed to find an effective method to reduce the noise level. In the acoustical analysis, the shape variations of frequency response function in the neighborhood of resonances are tested for three parameters: the height of remained oil, the suction position of refrigerant and the position of driving part. As a conclusion of this result, to reduce the emission noise of compressor during start-up, the height of remained oil should be kept at 16 mm, the refrigerant should be sucked at the cross point of nodal lines of X and Y directional cavity modes, and the driving part should be positioned in the center of cavity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.2
• /
• pp.25-32
• /
• 1994

The characteristics of the R-22 two-stage compression refrigeration systems were investigated. The apparatus consisted of 0.5HP and 1HP hermetic reciprocating compressors for the high and low stage sides respectively, a condenser, an evaporator, a heat exchanger, four expansion valves, and two intercoolers. The experiments covered a range of refrigerant flow rates from 24 to 84kg/h, and the inlet temperature of cooling water in the condenser and heat source water in the evaporator ranged from 20 to 30$^.\circ}C$The results Showed that the refrigerant flow rate had greater effect on the refrigerating capacities, the compression efficiency and the coefficient of performance of two-stage compression systems than the inlet temperature of heat source water. And all these values were decreased with increasing inlet temperatures of the cooling water. The pressure drops in the evaporator of two-stage compression systems were decreased in proportion to the increase in the inlet temperature of the heat source and cooling water, but it was increased by the refrigerant flow rate.

• Restorative Dentistry and Endodontics
• /
• v.41 no.2
• /
• pp.148-153
• /
• 2016

Tooth transposition is a disorder in which a permanent tooth develops and erupts in the normal position of another permanent tooth. Fusion and gemination are developmental disturbances presenting as the union of teeth. This article reports the nonsurgical retreatment of a very rare case of fused teeth with transposition. A patient was referred for endodontic treatment of her maxillary left first molar in the position of the first premolar, which was adjacent to it on the distobuccal side. Orthopantomography and periapical radiography showed two crowns sharing the same root, with a root canal treatment and an associated periapical lesion. Tooth fusion with transposition of a maxillary molar and a premolar was diagnosed. Nonsurgical endodontic retreatment was performed. At four yr follow-up, the tooth was asymptomatic and the radiolucency around the apical region had decreased, showing the success of our intervention. The diagnosis and treatment of fused teeth require special attention. The canal system should be carefully explored to obtain a full understanding of the anatomy, allowing it to be fully cleaned and obturated. Thermoplastic techniques were useful in obtaining hermetic obturation. A correct anatomical evaluation improves the set of treatment options under consideration, leading to a higher likelihood of esthetically and functionally successful treatment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.1
• /
• pp.31-38
• /
• 2022

TR module using in satellite must consider discriminative electrical and mechanical requirements compare to the one using in ground and aircraft system since not only the environment level of vibration and shock during the launch stage but also the level of radiation, vacuum and thermal variation from orbit environment are more severe than atmosphere condition. This paper describes the environmental conditions of launch and the orbit and, suggests design method of TR module applying GaN to satisfy the unique environmental requirements of satellite systems by especially focusing on parts selection, derating design, RF budget design, manufacturing process design, and thermal design of TR module.

• Tribology and Lubricants
• /
• v.36 no.3
• /
• pp.139-146
• /
• 2020

Global warming has led to an increase in demand of eco-friendly vehicles, such as electric cars, for reducing greenhouse gas emissions, and especially, regulating carbon dioxide generation. In addition, electric vehicles are equipped with an electric drive-type hermetic scroll compressor and a refrigerant, which exhibit current and future trends of using environmentally friendly refrigerants, including R-1234yf. In this study, polyol ester-based refrigeration oils are prepared via condensation esterification of polyol and fatty acids. The oils can be combined with R-1234yf refrigerant for applications in air conditioning and cooling systems of electric vehicles. The structure of synthetic polyol esters is confirmed via ¹H-NMR and FT-IR spectrum analysis, and the composition of the polyol ester is analyzed via gas chromatogram analysis. Furthermore, kinematic viscosity, viscosity index, total acid value, pour point, and color are analyzed as fundamental physical properties of the synthetic polyol esters. The compatibility and chemical stability of the synthetic polyol ester combined with the R-1234yf refrigerant are obtained via high temperature and high pressure oil-resistant refrigerant tests. The changes in the oil color and catalyst activity are observed before and after the experiment to determine whether it is suitable as a refrigerator oil.

• Journal of Biosystems Engineering
• /
• v.5 no.1
• /
• pp.33-42
• /
• 1980

This study was carried out to investigate the actual environmental paddy storage conditions in conventional Korean farm warehouses. The paddy storage conditions by the locations and sizes of warehouses were figured out. The effectiveness of the small insulated box for storing paddy was also examined. Observations were made at sixteen different warehouses located in Moonsan-Myeon, Jinyandg-gun, Gyungnam Province from July lst to September 28 th, the period which was considered to be the worst for storing grains. The results are as follows ; 1. the average temperatures of rough rice and air inside the warehouse were 0.9 and 0.7$^\circ$ higher than the outside air temperature. 2. The average relative humidity in warehouses was 1.5percent higher than that of the atomosphere. This fact resulted in the increased moisture content of grains. Therefore, the ventilation for equalizing the relative humidity of inside and outside of warehouses was required. 3. The dry matter of stored rough rice was decreased by 1.1 percent in average druing the observation period. In order to reduce the dry matter loss, application of new grain storing method ;hermetic storage or filling inert gas storage, was highly recommended. 4. Environmental conditions for storing rough rice in a warehouse located in a sloping site are, in general , better than those of a warehouse located in a flat site. But as far as the dry matter of rough rice was concerned, above situation is not always satisfactory. Because it is fairly frequent to observe the higher rate of moisture absorption by grains stored in a warehouse located in a sloping site. 5. Environmental conditions for storing rough rice in a large-scale warehouse were better than those in a small size warehouse. Therefore, it is advisible for farmers to store their grins in the large-scale warehouses commonly used by villagers. 6. It was undesirable to store rough in a insulated box.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.17-24
• /
• 1998

압축기의 종류는 크게 dynamic type과 positive displacement type으로 우선 나눌 수 있다. 전자는 제트엔진에 사용되는 압축기에서 보는 바와 같이 기체의 속도를 변화시켜 동압을 정압으로 바꾸어 압력을 얻는 경우이다. 후자는 기체를 둘러싼 체적을 줄여서 압력을 얻는데 가전제품에 쓰이는 냉각용 압축기의 대부분의 종류가 이에 해당된다. 압축 기체의 종류에 따라 공기 압축기, 가스 압축기, 냉각용 압축기로도 나눌 수 있겠다. 냉각용 압축기는 다시 여러 가지 방법으로 분류할 수 있겠지만, 구동 모타의 용량이나 냉각 용량에 따라, 대형, 소형으로 분류하거나, 압축기를 둘러싼 셀의 구조에 따라 밀폐형과 반 밀폐형으로 나눌 수 있다. 밀폐형은 냉매를 반 영구적으로 보충할 필요가 없도록 용접형 셀을 가진 구조로 압축기를 다시 열어서 보수할 수가 없다. 냉장고나 냉방기 같은 가전 제품에 쓰이는 압축기는 대부분 소형 밀폐형이 되겠다. 산업용의 중,대형 압축기는 보수의 목적으로, 자동차 냉방용 압축기는 동력이 엔진축에서 공급되는 구조 상의 이유로 반 밀폐형이 채택된다. 보수가 사실상 불가능한 밀폐형의 구조 상 소형 냉장용 압축기는 거의 무한 수명을 감안한 설계를 요하게 되고, 이것이 압축기의 보수적인 설계 및 개발 성향에 어느 정도 영향을 주었다고 볼 수 있다. 이런 소형 밀폐형 압축기(positive displacement, fractional horsepower, hermetic compressor)에 관한 연구의 소개가 이 글의 주 관심이 되겠다. 압력을 얻기 위해 체적을 변화시키는 mechanism도 여러 가지가 있는 바, 왕복동식 피스톤(reciprocating piston) 압축기가 가장 오랫동안 사용되어 온 구조이다. 회전식으로 압축을 얻는 방식으로는 로타리 피스톤식, 스크류식, 스크롤식 압축기가 있다. 로타리 피스톤(rotary piston)식 압축기는 약 20여년 전 부터 냉방용 압축기에서부터 널리 쓰이게 되었다. 약 10여년전부터 상용화 된 스크롤(scroll) 형 압축기도 현재 상대적으로 용량이 큰 가정용 냉방기를 중심으로 많이 쓰이고 있다. 스크류형 압축기는 보통 중대형 상업용에 주로 쓰인다.

• Journal of Biomedical Engineering Research
• /
• v.32 no.1
• /
• pp.45-54
• /
• 2011

Cuff electrodes have a benefit for chronic electroneurogram(ENG) recording while minimizing nerve damage. However, the ENG signals are usually contaminated by electromyogram(EMG) activity from the surrounding muscle, the thermal noise generated within the source resistance, and the electric noise generated primarily at the first stage of the amplifier. This paper proposes a new cuff electrode to reduce the interference of EMG signals. An additional middle electrode was placed at the center of cuff electrode. As a result, the proposed cuff electrode achieved a higher signal-to-interference ratio compared to the conventional tripolar cuff. The cuff electrode was then assembled together with closure, headstage, and hermetic case including electronic circuits. This paper also presents a lownoise amplifier system to improve signal-to-noise ratio. The circuit was designed based on the noise analysis to minimize the electronic noise. The result shows that the total noise of the amplifier was below $1{\mu}V_{rms}$ for a cuff impedance of $1\;k{\Omega}$ and the common-mode rejection ratio was 115 dB at 1 kHz. In the current study, the performance of nerve cuff electrode system was evaluated by monitoring afferent nerve signals under mechanical stimuli in a rat animal model.

• Advances in Energy Research
• /
• v.7 no.1
• /
• pp.1-19
• /
• 2020

Energy consumption of air-conditioning and refrigeration systems is responsible for about 25 to 30% of the energy demand especially in hot seasons. This equipment is mostly electricity dependent and their use in principle affects negatively the environment. Enhancing the energy efficiency of the existing equipment is important as one of the measures to reduce environment impacts. This paper reports the results of an experimental study to evaluate the impacts of the use electronic expansion valve and variable velocity compressor on the performance of vapor compression refrigeration system. The experimental rig is composed of two independent circuits one for the vapor compression system and the other is the secondary fluid system. The vapor compression system is composed of a forced air condenser unit, evaporator, hermetic compressor and expansion elements, while the secondary system has a pump for circulating the secondary fluid, and an air conditioning heat exchanger. The manufacturer's data was used to determine the optimal points of operation of the system and consequently tests were done to evaluate the influence of variation of the compressor velocity and the opening of the expansion device on the performance of the refrigeration system. A fuzzy logic model was developed to control the rotational velocity of the compressor and the thermal load. Fuzzy control model was made in LabVIEW software with the objective of improving the system performance, stability and energy saving. The results showed that the use of fuzzy logic as a form of control strategy resulted in a better energy efficiency.

• Journal of Plant Biotechnology
• /
• v.30 no.4
• /
• pp.387-397
• /
• 2003

During the first half of twentieth century, even though the importance of non-calorie essential micronutrients of 13 vitamins and 17 minerals has been known to alleviate nutritional disorder; the primary objective of agriculture and plant breeding programs has been to increase the productivity and seed yields, and macronutrients of proteins, fats, and carbohydrates made up the bulk of foodstuff which were used primarily as an energy source. In the last decade it has been found that non-essential micronutrients encompass a vast group of phytochemicals including antioxidants that are not strictly required in the diet but when present at sufficient levels work as health-promoting chemicals. Nowadays agricultural crops are grown for health rather than for food or fiber, and modifying the nutritional compositions of plant foods has become an urgent health issue. To ensure an adequate intake of essential vitamins and minerals, and to increase the consumption of health-promoting phytochemicals, the researches on plant secondary metabolism have been made. The attempt to improve nutritional quality of crops has been blocked by a lack of basic knowledge of plant metabolism. The advent of genomics era enabled new approaches to make crossing regardless of species, family, or phylum barriers, and the accumulation in our basic knowledge on plant secondary metabolism during the coming decade would be tremendous. As the major staple crops contain insufficient amount of many micronutrients, fortification strategy will be a necessary practice. Elevated intake of specific vitamins, C, E, and $\beta$-carotene, mineral selenium, antioxidants, and phytochemicals significantly reduces the risk of chronic disease such as cancer, cardiovascular disorder, diabetis, and other degenerative disease associated with aging. As the attempt to improve the nutritional quality of crops requires the basic knowledges on plant metabolism, plant biochemistry, human physiology, and food chemistry, strong interdisplinary collaboration among plant biotechnologists, human nutritionists, and food scientists will be needed. Inhibition of cancer, cardiovascular disease, and other degenerative disorder may be the biggest goal facing nutritional plant breeders. But the assumption that simply increasing dietary level of any compound will necessarily improve human health is a dangerous idea because many plant secondary products and dietary contaminants have paradoxical (hermetic) effects. Before biotechnical manipulation is undertaken to elevate or reduce any individual constituent of crops, the contribution of the micronutrient to human health must first be investigated.