• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1998년도 제13차 학술회의논문집
• /
• pp.95-99
• /
• 1998

We introduce an autonomous flying system using a model-helicopter. A feature of the helicopter is that autonomous flight is realized on the low-cost compact model-helicopter. Our helicopter system is divided into two parts. One is on the helicopter, and the other is on the land. The helicopter is loaded with a vision sensor and an electronic compass including a tilt sensor. The control system on the land monitors the helicopter movement and controls. We firstly introduce the configuration of our helicopter system with a vision sensor and an electronic compass. To determine the 3-D position and posture of helicopter, a technique of image recognition using a monocular image is described based on the idea of the sensor fusion of vision and electronic compass. Finally, we show an experiment result, which we obtained in the hovering. The result shows the effectiveness of our system in the compact model-helicopter.

• Journal of Biosystems Engineering
• /
• 제35권5호
• /
• pp.302-309
• /
• 2010

Aerial application using an unmanned agricultural helicopter would allow precise and timely spraying. The attitude of a helicopter depends on a number of dynamic variables for roll-balanced flight. Laterally tilting behavior of a helicopter is a physically intrinsic phenomenon while hovering and forwarding. In order to balance the fuselage, the rotor should be counter-tilted, resulting in the biased down-wash. The biased spraying toward right side causes uneven spray pattern. In this study, a raised tail rotor system for the roll-balanced helicopter was studied. Thrust of the tail rotor system was measured and theoretically estimated for the fundamental database of the roll-balanced helicopter design. The estimated tail thrust and roll-moment would be used to design the raising height of tail rotor and roll balancing dynamics. The unmanned agricultural helicopter required the tail rotor thrust of about 39.2 N (4.0 kgf) during hovering with a payload of 235.4 N (24 kgf). A raised tail rotor system would compensate for the physical tilt phenomena. A further attitude control system of helicopter would assist roll-balanced aerial spray application.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1504-1508
• /
• 1996

In this paper, we derive dynamic equation of helicopter and design controller based on variable structure system. It is difficult to control helicopter because it has non-linear coupling between input and output of system and is MIMO system. The design of control law is considered here using variable structure methodology giving the robustness to parameter variations and invariance to some subsets of external disturbance. However we derive dynamic equations of helicopter and design stabilizing variable structure controller. Also, simulation results are given in this paper.

• 한국항행학회논문지
• /
• 제17권6호
• /
• pp.798-803
• /
• 2013

본 논문에서는 헬기운항안전 향상을 위한 북미대륙의 활동들을 소개하였다. 북미지역에서는 2009년 기준으로 전세계 민간헬기의 49%가 운용되고 있어, 이 지역에서의 헬기 운항안전을 위한 개발동향은 여타 헬기 운용지역에도 상당한 영향을 미칠 것으로 예상된다. 대규모 헬기가 운용되는 멕시코만의 헬기 운항안전을 위한 개발 사례와 미국 연방항공청(FAA, Federal Aviation Administration)의 NextGen 프로그램 및 국제민간항공기구 (ICAO, International Civil Aviation Organization)의 항공시스템블록업그레이드(ASBU, Aviation System Block Upgrades) 계획 실행을 위한 캐나다 계획 분석을 통해 헬기 관련 인프라 구축 동향 및 향후 헬기 운항안전 증진을 위해 나아갈 바와 기대효과에 대해 정리하였다.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 1999년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.281-284
• /
• 1999

Ground truth measurement system using RC helicopter is very useful to measure BRDF. The helicopter is operated human operator but it can keep its position by GPS aided hovering system. We developed the measurement system and have done ground truth in Mongolia in the summer of 1999 and have made sure the system can measure BRDF expectedly.

• Journal of Biosystems Engineering
• /
• 제33권2호
• /
• pp.94-100
• /
• 2008

Present chemical application method using a power sprayer has been labor intensive, costly and ineffective. Therefore, a small agricultural unmanned helicopter was suggested to replace the conventional spray system. In this study, conceptual design for developing the helicopter and a consequential prototype were reported. The overall conceptual design was initiated by deciding the type of agricultural helicopter, as the single rotor helicopter with a tail system. As the first step of the designing, an air-cooled, 2-stroke engine was selected and a prototype transmission was designed by determining the rotating speed of main rotor shaft. A 'pusher' type tail rotor system was adapted to balance the reaction torque and reduce the power use. The tail boom length was designed to avoid the rotating trajectory of the main rotor. The RF console consisted of the engine control, attitude control, and emergency control modules. Assembling the prototype concluded the mechanical development of the agricultural helicopter.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 춘계학술대회 논문집
• /
• pp.168-171
• /
• 2003

We introduced a small-sized automatic model helicopter for using in the remote sensing. The feature of our helicopter system is that the helicopter system is realized using commercialized radio-controlled model helicopter, whose payload is 1.5 kg. Therefore, our system has may benefits when apply our system to practical tasks. The compactness and light-weight of our system is realized by the introduction of our original technique to suppress the vibration noise using a slimy material as well as the introduction of latest sensors and semiconductor products. Submerging the acceleration sensor into a slimy material, moise ratio is highly improved. In this paper, we show an experimental results for the effect of our orignal technique to remove the vibration noise of helicopter. The result of hovering flying test shows the effectiveness of our system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1136-1141
• /
• 2008

The helicopter rotor system generates lift, thrust, maneuvering force and moment to the helicopter with the torque and pitch control force transferred from the main rotor hub/control. And the tail rotor system generates the thrust for yaw axis control of the helicopter with the torque and pitch control force transferred from the tail rotor hub/control. Ground whirl test shall be performed to verify the compliance of requirement performance test and dynamic test of rotor blade and hub/control. This paper describes a design of whirl tower test facility for helicopter rotor system test and evaluation. Design results are summarized and compared with design requirements.

• 대한임베디드공학회논문지
• /
• 제6권5호
• /
• pp.303-309
• /
• 2011

In this paper, an intelligent force control technique is applied to an autonomous helicopter. Although most research on the autonomous helicopter system is about navigation and control, force control of an autonomous helicopter system is quite new and not presented yet. After controlling the position of the helicopter by the LQR method, force control is applied. The adaptive impedance force control algorithm is introduced and tested to regulate the desired force under unknown location and stiffness of the environment. To compensate for uncertainty from outer disturbance, a neural network is added to form an intelligent force control framework. Simulation studies show that the proposed force control algorithm works well.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.484-489
• /
• 2011

In this paper, it was described the current technology status of bearingless rotor hub system for helicopter which is one of major rotor hub system. Also, a conceptual study on the new bearingless rotor hub system of helicopter was described. First, the advantages and disadvantages of major helicopter rotor hub system are described in comparison to each other types of rotor hub system. The unique characteristics of bearingless rotor hub system are described compared to other types of rotor hub systems. Next, the main function, role and characteristics of the sub-components of bearingless rotor hub system are described. Recent helicopters which adopt this bearingless rotor hub system are described and introduced. This conceptual study shows that double-H sectional construction and rectangular construction of flexbeam are the most effective candidates of this new bearingless rotor system. This bearingless rotor hub system can be used for 7,000lbs class helicopter. Now, a further trade-off study will show.