• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.329-329
• /
• 2017

In this study attempted to evaluate the stability of the protection methods by examining hydraulic characteristics of the area around the point in which marine cable protector is installed such as surf zone occurrence point of shore-end submarine cables suitable for coastal marine environmental conditions, flow rate t the tope of the protector and maximum wave height, and to provide basic data for the selection of the optimal protection method. In performing hydraulic model experiments, the topography of submarine cable installation location was reproduced in 2-D sectional channel, and models appropriate for experimental scale and similitude law were produced and installed for each condition of submarine cables and protectors. Since the topography and submarine cable protectors were reproduced and installed in 2-D sectional channel, the exact reproduction of surf and transformation in shallow water zone was possible, and thus the physical properties could be clearly analyzed. For stability review, an experiment to examine the stability was conducted using a wave maker with 50-year frequency design waves as target, and wave height and cycles were applied based on the approximate lowest low water level(Approx. L.L.W), which is the most dangerous in submarine cable protection methods. As for experimental time, typhoon passing time in summer (about 3 hours) was applied, and wave patterns and deviation ratio of the submarine cable protector were investigated after making irregular waves corresponding to design waves. In addition, current meter and wave height meter were installed at the installation location of the submarine cable protector, and the flow rates and wave height at the top of the protector were measured and analyzed to review hydraulic properties.

• Journal of Environmental Health Sciences
• /
• v.41 no.5
• /
• pp.277-288
• /
• 2015

Objectives: There are many hazardous agents at livestock farms. In particular, gases can be detrimental to both workers and animals. This study evaluated ammonia and hydrogen sulfide concentrations in broiler hen barns and beef cattle barns according to sampling location and height. Methods: Three broiler hen barns and three beef cattle barns were selected for gas monitoring in this study. Ammonia and hydrogen sulfide concentrations were measured using a direct-reading instrument which could measure the target gases simultaneously. Gas monitoring was conducted at human breathing height and animal breathing height at three points in each livestock farm. Results: Ammonia concentrations at the broiler hen barns ranged from 3.3 to 12.5 ppm by sampling location and height, but hydrogen sulfide was not detected. In the beef cattle barns, ammonia ranged from 3.1 to 16.3 ppm and low concentrations of hydrogen sulfide were detected at some animal breathing heights. The gas concentrations detected at each livestock farm were significantly higher in the animal breathing zones than in human breathing zones (p<0.0001). Conclusions: We found a difference in gas concentrations between human breathing zones and animal breathing zones. Gas monitoring should be conducted to improve the related environment considering both workers' and animals' health and safety.

• Industrial Engineering and Management Systems
• /
• v.3 no.2
• /
• pp.129-133
• /
• 2004

Studies on the optimal location of retail store have been made in case of no obstacle(Minagawa etal. 1999). This paper deals with the location problem of retail store considering obstacles (e.g. rivers, railways, highways, etc.) and obstacle-overcoming points (e.g. bridges, railway crossings, zebra crossings, overpasses, etc.). We assume that (1) commercial goods dealt here are typically convenience goods, (2) the population is granted as potential demand, (3) the apparent demand is a function of the maximum migration length and the distance from the store to customers, (4) the scale of a store is same in every place and (5) there is no competitor. First, we construct the basic model of customers' behavior considering obstacles and obstacle-overcoming points. Analyzing the two dimensional model, the arbitrary force attracting customers is represented as a height of a cone where the retail store is located on the center. Second, we formulate the total demand of customers and determine the optimal location that maximizes the total demand. Finally, the properties of the optimal location are investigated by simulation.

• Steel and Composite Structures
• /
• v.50 no.1
• /
• pp.1-13
• /
• 2024

The objective of this research is to study experimentally and numerically the behavior of steel beam columns with openings. Although the presence of openings in the beam columns is inevitable, finding ways to maintain strength is crucial. The studied parameters are opening shape, the ratio between opening height to specimen height, the percentage of opening location from support to beam column length, and web slenderness. Experimental tests are conducted including twelve specimens to study the effect of these parameters and record failure load, load deflection curve, and stress strain curve. Two failure modes are observed: local and flexural buckling. Interaction curves plotted from finite element model analysis are also used to expand the parametric study. Changing the location of the opening can decrease failure load by up to 7% and 60% in both normal and moment ratios respectively. Increasing the opening dimension can lead to a drop in the axial ratio by up to 29% and in the moment ratio by up to 74%. The weakest beam column behavior is noticed in specimens with rectangular openings which results from uneven and concentrated stresses around the opening. The main results of this research illustrate that the best location for opening is at 40% - 50% from beam column support. Also, it is advisable to use circular openings instead of rectangular openings in specimens having slender webs because moment ratios are raised by 85% accompanied by a rise in normal ratios by 9%.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.5
• /
• pp.340-352
• /
• 2011

This study was carried out to analyze the change of wind filed and heat island according to the location of the high rise building using micrometeorology numerical model Envi-met3.0. In this study, the real urban planning of Jeonju city was used as input for the location and height of buildings. Modeling was performed for two conditions as input data. Case 1 is that wind direction is SSE and case 2 is W. To analyse the change of wind filed, wind speed results were used. To analyze the change of heat island, temperature results were used. Below the building height, wind speed increased 0.2~2.5 m/s at the inflow area and decreased 0.5~2.0 m/s at the area between the buildings. Above the building height, wind speed decreased 0.1~0.8 m/s near the building complex. On the other hand, wind speed increased 0.2~0.4 m/s in the outside area of the building complex. In the case of temperature, below the building height, temperatures increased $0.01{\sim}0.1^{\circ}C$ in the building complex and leeward area. On the other hand, temperature decreased $0.01{\sim}0.005^{\circ}C$ in the outside area of the building complex. Above the buildings height, temperatures decreased $0.05{\sim}0.2^{\circ}C$ in most of the area.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.726-733
• /
• 2016

In this study, a computer simulation of the three types of air distribution systems, open type system, aisle partition system and aisle containment system, to evaluate the applicability of the aisle partition system on a data center server room. The variables of the simulation were the height and location of the partition fixed on the top server rack. The energy efficiency of the air distribution systems were confirmed to be excellent in the order of the aisle containment system, aisle partition system, and open type system. In the cold aisle partition system, the height of the partition that can be effective in saving cooling energy by obstructing sufficient air recirculation was found to be more than 0.9m. In the hot aisle partition system, the height of the partition was found to be more than 0.8m.

• Korean Journal of Ecology and Environment
• /
• v.49 no.3
• /
• pp.236-243
• /
• 2016

It was a case study to use as a basic data for efficient the preservation and management of subalpine coniferous forest in national parks. It is based on inhabitation condition of 210 individuals of Abies koreana Wilson that was found through local investigation in the sub-alpine zone of Jirisan National Park and Songnisan National Park. It analyzed the effect of the geographical location and topographical features, which are the basics of location environment, on the growth of A. koreana. The variables related to the growth of A. koreana are tree height and diameter at breast height. Topographical features include geographical longitude, altitude above sea level, slope of the mountains, aspect that describes the direction in which a slope faces and topographical wetness index. Topographical features were extracted through GIS spatial analysis. It used canonical correlation analysis to estimate whether the two variables groups have related to each other and how much they are related, if any, and estimated the effect of the geographical and topographical features on the growth structure of A. koreana using multiple regression analysis. The tree height and diameter at breast height that represent the growth structure of A. koreana show greater relation to geographical latitude distribution than topographical feature and the geographical and topographical factors show greater relation to diameter at breast height than tree height. The growth structure's variable and geographical and topographical variable of A. koreana have meaningful relation and the result shows that geographical and topographical variables explain 18.1% of the growth structure. The variables that affect the diameter at breast height of A. koreana are geographical latitude, topographical wetness index, aspect and altitude, which are put in order of statistical significance. The higher the latitude is, the smaller the diameter at breast height. Depending on the topographical feature, it becomes bigger. The variable that affects the tree height is topographical wetness index, which was the only meaningful variable. Overall, the tree height and diameter at breast height that are related to the growth structure of A. koreana are affected by geographical and topographical feature. It showed that the geographical feature affected it the most. Especially the effect of water among the topographical features is expected to be bigger than the other topographical factors. Based on the result, it is expected that geographical and topographical feature is an important factor for the growth structure of A. koreana. Even though it considered only the geographical and topographical features and used spatial analysis data produced by GIS, the research results will be useful for investigating and researching the growth environment of coniferous forest inhabiting in sub-alpine zone of national parks and are expected to be used as basic data for establishing measures to efficiently manage and preserve evergreen needleaf tree such as A. koreana.

• Journal of Korean Society of Forest Science
• /
• v.99 no.2
• /
• pp.204-212
• /
• 2010

This study was performed in 22 unthinned Larix olgensis plantations in northeast China. Data were collected on 95 sample trees of different canopy positions and the diameter at breast height ($d_{1.3}$) ranged from 5.7 cm to 40.2 cm. The individual tree models for the prediction of vertical distribution of live crown, branch and needle biomass were built. Our study showed that the crown, branch and needle biomass distributions were most in the location of 60% crown length. These results were also parallel to previous crown studies. The cumulative relative biomass of live crown, branch and needle were fitted by the sigmoid shape curve and the fitting results were quite well. Meanwhile, we developed the crown ratio and width models. Tree height was the most important predictor for crown ratio model. A negative competition factor, ccf and bas which reflected the effect of suppression on a tree, reduced the crown ratio estimates. The height-diameter ratio was a significant predictor. The higher the height-diameter ratio, the higher crown ratio is. Diameter at breast height is the strongest predictor in crown width model. The models can be used for the planning of harvesting operations, for the selection of feasible harvesting methods, and for the estimation of nutrient removals of different harvesting practices.

• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.281-286
• /
• 2022

In this study, the effects of Elasto-hydrodynamic lubrication pressure on the critical shoulder height of raceway in an angular contact ball bearing were investigated. Both 3D contact analyses using an influence function and the EHL analysis were conducted for the contact geometry between the ball and raceways. The pressure distributions by 3D contact analysis and EHL analysis for an example bearing were compared. The effect of ellipse truncation on the minimum film thickness also investigated from EHL analysis. The critical shoulder height in the dry contact and the EHL state were compared for various applied loads. It is shown that when the ellipse truncation occurs, the pressure spike for the EHL conjunction is higher than that for the dry contact, and its location moves more inward of the contact center. The steep pressure gradients would increase the flow rate, so in order to maintain flow continuity a significant reduction in film thickness and an abrupt rise in pressure occurs in the edge of shoulder. Significant reduction of the minimum film thickness occurs near the edge of shoulder. The critical shoulder heights in the EHL state are calculated as higher values compared with in the dry contact. This results shows that the determination of critical shoulder height by the EHL analysis is more proper.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2670-2680
• /
• 1996

Effeccs of porous wind fence on surface-pressure around 2-dimensional prism model of triangular cross-section were investigated experimentally. The pressure data were obtained at a Reynolds number based on the model height of Re=2.1*10$^{5}$ . Flow visualization also carried out to investigate the flow structure qualitatively. The mean velocity and turbulent intensity profiles measured at fence location were well fitted to the neutral atmospheric surface boundary layer over the open terrain. Various fences with different porosity and height were tested to investigate their effects on the surface pressure acting on a prism model at different locations. As the results, porous fence with porosity 40 ~ 50% is most effective for abating wind erosion. With decreasing porosity of the fence, pressure fluctuations on the model surface are increased. The mean pressure coefficients are decreased only when the fence height is greater than the model height. The effect of distance between wind fence and triangular prism was not significant, compared to that of the fence porosity and height.