• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.191-196
• /
• 2005

A full-bead of multi-layer-steel (MLS) engine head gasket is used to seal the combustion gas. Finite element analyses were conducted to assess the dependence of the sealing performance of full-bead on the forming process consisting of embossing and flatting operations. It is demonstrated that the sealing performance is enhanced with more severe deformation of the bead plate during the embossing, i.e., with the increase in the punching depth, the punch height, the punch width and the friction coefficient of the bead plate against the punch and die, and with the decrease in the width of die cavity. Meanwhile, the flatting process that is employed to adjust the height of the embossed full-bead has no influence on the sealing performance.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1637-1639
• /
• 2005

The measurement of magnetic field is performed about DC and AC magnetic field in test track of depot. The test point is cap, on the converter/inverter box, on the traction motor, on the APSE and on the line filter, the height of measurement is bottom and 50 cm height. In case of AC magnetic field, the selected specific frequency is measured on the converter/inverter box. The AC magnetic field is checked and analysis through RS-232C and notebook PC. The DC magnetic field is measured by using the Hall Probe, test result is saved and analysis by PXI system. On the line filter, the maximum value is 1.4 mT in case of DC magnetic field and 0.044 mT in case of AC magnetic field at 50 Hz.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2290-2295
• /
• 2005

In this paper, it is developed simulator system of 3 D.O.F parallel robot for educate of expertness. This simulator system is composed of three parts ? 3 D.O.F parallel robot, controller (hardware) and software. First, basic structure of the robot is 3 active rotary actuator that small geared step motor with fixed base. An input-link is connected to this actuator, and this input-link can connect two ball joints. Thus, two couplers can be connected to the input-link as a pair. An end-plate, which is jointed by a ball joint, can be connected to the opposite side of the coupler. A sub-link is produced and installed to the internal spring, and then this sub-link is connected to the upper and bottom side of the coupler in order to prevent a certain bending or deformation of the two couplers. The robot has the maximum diameter of 230 mm, 10 kg of weight (include the table), and maximum height of 300 mm. Hardware for control of the robot is composed of computer, micro controller, pulse generator, and motor driver. The PC used in the controller sends commands to the controller, and transform signals input by the user to the coordinate value of the robot by substituting it into equations of kinematics and inverse kinematics. A controller transfer the coordinate value calculated in the PC to a pulse generator by transforming it into signals. A pulse generator analyzes commands, which include the information received from the micro controller. A motor driver transfer the pulse received from the pulse generator to a step motor, and protects against the over-load of the motor Finally, software is a learning purposed control program, which presents the principle of a robot operation and actual implementation. The benefit of this program is that easy for a novice to use. Developed robot simulator system can be practically applied to understand the principle of parallel mechanism, motors, sensor, and various other parts.

• Annals of Clinical Neurophysiology
• /
• v.1 no.2
• /
• pp.118-125
• /
• 1999

Background and Aims : Nerve conduction study is invaluable in clinical neurology, especially for assessing peripheral neuropathies. Abnormal nerve conduction studies may result not only from peripheral nerve dysfunction itself, but also from other various mechanical, technical, and physiological factors such as age, sex, height and temperature. So we conducted this study to establish the our own normal values. Methods : In this study, from March. 1997 to July. 1998, 40 Korean adults among person came to Health Promotion Center over the age of 20 without any suspicion of neurological deficits were analysed to determine the effect of compound effects of several physiological factors. Results : The nerve conduction velocities of the upper extremity and proximal segments were faster than those of the lower extremity and distal segments. Physiological factors such as age, height and temperature affect the results of nerve conduction studies in multiple regression analysis. The sex difference is recognized over peroneal motor nerve. There are no sex differences in amplitude transformed into normal distribution. The significant physiological factor affecting the amplitude of nerve conduction is age, whereas height and temperature play no role. Conclusions : In multiple regression analysis, height is widespread variable for the nerve conduction velocities and temperature is important variable for lower extremities. The parametric statistical analysis cannot be applied to the amplitude of the compound muscle or nerve action potentials because of marked left shift in distribution. Sqareroot transformation of the CMAP and CNAP may be useful in normalizing the distribution. The most significant physiological factor affection the amplitude is age. Sex differences are not seen in nerve conduction study.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.574-575
• /
• 2010

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.11 no.1
• /
• pp.29-35
• /
• 2017

It was hard for a conventional care-bed to be realized to a low-floor position due to a complex actuation mechanism installed under the mattress support platform. In this paper a mechanism design to set a low-floor position as well as to adjust back- and leg-rest angles was proposed. A dual motor was applied to the back- and leg-rest mechanism of which design parameters were determined by an optimal method. An elevation mechanism was also designed to enlarge a limited stroke range up to two times of its original stroke using a pulley mechanism. An evaluation test was performed by five healthy subjects ($24.4{\pm}0.5yrs.$) when going up from a floor position to a preset best position which was set to the 240mm height for a prototype low-floor bed and to the 600mm height for a conventional bed. As a result, the moving distance was 38% lower than the conventional bed when the subject used the low-floor bed. It showed that the low-floor care-bed reduced physical burdens and was effective to assist activities of daily living of the elderly people.

• Journal of Trauma and Injury
• /
• v.37 no.1
• /
• pp.67-73
• /
• 2024

Purpose: Posttraumatic stress disorder (PTSD) is prevalent and is associated with protracted recovery and worse outcomes after injury. This study compared PTSD prevalence using the PTSD Checklist for DSM-5 (PCL-5) with the prevalence of PTSD risk using the Injured Trauma Survivor Screen (ITSS). Methods: Adult trauma patients at a level I trauma center were screened with the PCL-5 (sample 1) at follow-up visits or using the ITSS as inpatients (sample 2). Results: Sample 1 (n=285) had significantly fewer patients with gunshot wounds than sample 2 (n=45) (8.1% vs. 22.2%, P=0.003), nonsignificantly fewer patients with a fall from a height (17.2% vs. 28.9%, P=0.06), and similar numbers of patients with motor vehicle collision (40.7% vs. 37.8%, P=0.07). Screening was performed at a mean of 154 days following injury for sample 1 versus 7.1 days in sample 2. The mean age of the patients in sample 1 was 45.4 years, and the mean age of those in sample 2 was 46.1 years. The two samples had similar proportions of female patients (38.2% vs. 40.0%, P=0.80). The positive screening rate was 18.9% in sample 1 and 40.0% in sample 2 (P=0.001). For specific mechanisms, the positive rates were as follows: motor vehicle collisions, 17.2% in sample 1 and 17.6% in sample 2 (P>0.999); fall from height, 12.2% in sample 1 and 30.8% in sample 2 (P=0.20); and gunshot wounds, 39.1% in sample 1 and 80.0% in sample 2 (P=0.06). Conclusions: The ITSS was obtained earlier than PCL-5 and may identify PTSD in more orthopedic trauma patients. Differences in the frequency of PTSD may also be related to the screening tool itself, or underlying patient risk factors, such as mechanism of injury, or mental or social health.

• Journal of Korean Neurosurgical Society
• /
• v.55 no.2
• /
• pp.73-77
• /
• 2014

Objective : The purpose of this study was to evaluate the efficacy of implant removal of percutaneous short segment fixation after vertebral fracture consolidation in terms of motion preservation. Methods : Between May 2007 and January 2011, 44 patients underwent percutaneous short segment screw fixation due to a thoracolumbar burst fracture. Sixteen of these patients, who underwent implant removal 12 months after screw fixation, were enrolled in this study. Motor power was intact in all patients, despite significant vertebral height loss and canal compromise. The patients were divided into two groups by degree of osteoporosis : Group A (n=8), the non-osteoporotic group, and Group B (n=8), the osteoporotic group. Imaging and clinical findings including vertebral height loss, kyphotic angle, range of motion (ROM), and complications were analyzed. Results : Significant pain relief was achieved in both groups at final follow-up versus preoperative values. In terms of vertebral height loss, both groups showed significant improvement at 12 months after screw fixation and restored vertebral height was maintained to final follow-up in spite of some correction loss. ROM (measured using Cobb's method) in flexion and extension in Group A was $10.5^{\circ}$ ($19.5/9.0^{\circ}$) at last follow-up, and in Group B was $10.2^{\circ}$ ($18.8/8.6^{\circ}$) at last follow-up. Both groups showed marked improvement in ROM as compared with the screw fixation state, which was considered motionless. Conclusion : Removal of percutaneous implants after vertebral fracture consolidation can be an effective treatment to preserve motion regardless of osteoporosis for thoracolumbar burst fractures.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.175-181
• /
• 2014

A four-link mechanism consisting of torsion bars is used for opening the trunk lid in most midsize sedans. When the weight of the lid is in equilibrium with the spring force exerted by torsion bars, the lid stops opening at a pop-up height. However, the actual pop-up height has large deviations from the specified height even with the same parts in the same car model, which leads to quality issues. Automotive manufacturers have experienced this deviation problem despite much effort to resolve it. In this research, we developed a multi-body dynamics model for the analysis of pop-up deviation of a trunk lid with torsion bars, which can simulate the actual pop-up motion of the trunk lid by considering kinematic constraints of the motion and friction forces in joints. We could also determine the most important factor that governs the pop-up height by sensitivity analysis of all parts. The developed system can be used for the analysis of other trunk lid systems to control the tolerance of parts.

• Physical Therapy Korea
• /
• v.8 no.1
• /
• pp.51-58
• /
• 2001

In children with cerebral palsy, bone density is decreased by disturbance of bone remodelling due to lack of normal weight bearing and muscle contraction through physical activity. Loss of bone density cause fracture, delays treatment with immobilization, and leads to functional limitation. The purpose of this study was to investigate bone mineral density of lumbar spine in children with spastic quadriplegia and diplegia. Six spastic quadriplegia and 14 spastic diplegia were evaluated in this study. QDR 4500 X-ray densitometer was used to measure bone density at lumbar spine (L1~L4). Children with cerebral palsy showed lower bone density than that of normal children. Bone density in children with spastic quadriplegia and diplegia was $-1.812{\pm}.962$, $-1.519{\pm}.935$, respectively. However, there was no significant differences in bone density between children with spastic quadriplegia and diplegia. There was no significant difference in bone density relation to motor development level, height, and weight. Further study is needed to find the appropriate interventions for preventing loss of bone density in children with cerebral palsy.